occurrence RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Workshop Manual

13B-151
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF196
PRESENT
OR
STOREDPEDAL SENSOR CIRCUIT GANG 1
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
1.DEF: Consistency between gang 1 and gang 2
NOTESPriorities when dealing with a number of faults:
– DF011 Sensor voltage supply no. 1
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after a series of full load / no load actions on the
accelerator pedal.
Special notes:
– engine torque limited,
– cruise control not authorised,
–the level 1 warning light is illuminated,
– idle speed is 1400 rpm,
Use bornier Elé. 1681 for any work on the computer connectors.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
CO.0
NOTESIf there is a simultaneous occurrence of fault DF198 Pedal
sensor circuit gang 2, check that the pedal sensor
connector is connected correctly.
Check the condition of the pedal sensor connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel
Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 921).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF196 / EDC16CP33_V1C_DF196 / EDC16CP33_V54_DF196 / EDC16CP33_V20_DF196 / EDC16CP33_V58_DF196 /
EDC16CP33_V5C_DF196 / EDC16CP33_V24_DF196 / EDC16CP33_V04_DF196 / EDC16CP33_V08_DF196 / EDC16CP33_V44_DF196 /
EDC16CP33_V4C_DF196 / EDC16CP33_V34_DF196 / EDC16CP33_V38_DF196 / EDC16CP33_V74_DF196 / EDC16CP33_V28_DF196 /
EDC16CP33_V62_DF196 / EDC16CP33_V26_DF196 / EDC16CP33_V60_DF196
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-155
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$073.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DF198
PRESENT
OR
STOREDPEDAL SENSOR CIRCUIT GANG 2
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
1.DEF: Consistency between gang 1 and gang 2
NOTESPriorities when dealing with a number of faults:
– DF012 Sensor supply voltage no. 2.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after a series of full load / no load actions on the
accelerator pedal.
Special notes:
– engine torque limited,
– cruise control not authorised,
–the level 1 warning light is illuminated,
– the idling speed is 1400 rpm.
Use bornier Elé. 1681 for any work on the computer connectors
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
CO.0
NOTESIf there is a simultaneous occurrence of fault DF196 Pedal
sensor circuit gang 1, check that the pedal sensor
connector is connected correctly.
Check the condition of the pedal sensor connector (see Wiring Diagram Technical Note, Laguna II ph2, Vel
Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 921).
Check the condition of the engine management computer connector (see Wiring Diagram Technical Note,
Laguna II ph2, Vel Satis ph2, Espace IV ph2, Mégane II ph2, Scénic II ph2, component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
EDC16CP33_V18_DF198 / EDC16CP33_V1C_DF198 / EDC16CP33_V54_DF198 / EDC16CP33_V20_DF198 / EDC16CP33_V58_DF198 /
EDC16CP33_V5C_DF198 / EDC16CP33_V24_DF198 / EDC16CP33_V04_DF198 / EDC16CP33_V08_DF198 / EDC16CP33_V44_DF198 /
EDC16CP33_V4C_DF198 / EDC16CP33_V34_DF198 / EDC16CP33_V38_DF198 / EDC16CP33_V74_DF198 / EDC16CP33_V28_DF198 /
EDC16CP33_V62_DF198 / EDC16CP33_V26_DF198 / EDC16CP33_V60_DF198
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74