wheel RENAULT TWINGO 2009 2.G Air Conditioning Owner's Guide

62A-18
AIR CONDITIONING
Compressor: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).aDrain the refrigerant circuit using a refrigerant
charging station (see 62A, Air conditioning, Re-
frigerant circuit: Draining - Filling, page 62A-8) .
aDisconnect the battery (see ) (80A, Battery).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the accessories belt (see Accessories belt: Re-
moval - Refitting) (10A, Engine and peripherals).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolts (1) from the connecting pipes on
the compressor. Equipment required
refrigerant charging station
compressed air nozzle
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair:
- (see 62A, Air conditioning, Air conditioning:
Precautions for the repair, page 62A-1) ,
- (see Vehicle: Precautions for the repair) (01D,
Mechanical introduction).
Note:
Use blanking plugs for the fuel circuits with part
numbers 77 01 208 229 or 77 01 476 857 to plug
any openings exposed to the open air. They must
be clean. Do not use any which have already been
used to plug a fuel circuit.
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which are
open to the air.
WARNING
In order to avoid any refrigerant leaks, do not dam-
age (deform, twist, etc.) the pipe.
WARNING
Consult the device's operating manual to avoid
incorrect use.
121175

62A-20
AIR CONDITIONING
Compressor: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
aUse a compressed air nozzle to blow on the sur-
face and the seal of the connecting pipe.
aLubricate the surface of the connecting pipe and the
seal with air conditioning oil (see 62A, Air condi-
tioning, Air conditioning: Parts and consum-
ables for the repair, page 62A-2) .
aRemove the blanking plugs.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the compressor.
aConnect the compressor connector.
aPosition the compressor connecting pipes.
aRefit:
-the bolts of the connecting pipes on the compres-
sor,
-the bolt of the connecting pipe bracket on the com-
pressor.
III - FINAL OPERATION
aRefit:
-the accessories belt (see Accessories belt: Re-
moval - Refitting) (10A, Engine and peripherals),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aConnect the battery (see ) (80A, Battery).
aConsult the amount of refrigerant and oil required
before filling the air conditioning circuit (see 62A, Air
conditioning, Air conditioning: Parts and con-
sumables for the repair, page 62A-2) .
aFill the refrigerant circuit using a refrigerant charg-
ing station (see 62A, Air conditioning, Refriger-
ant circuit: Draining - Filling, page 62A-8) .
aIn the event of replacement, apply the after repair
procedure:
-Switch on the ignition,
-Check that the air conditioning is off,
-Switch the ventilation to speed 2,
-Put the temperature setting at minimum,
-Select the air recirculation position,
-Start the engine.
-Run the air conditioning in manual mode (in the
case of climate control do not press auto),
-Run the engine at idle speed for 3 minutes with air
conditioning,
-Switch off the engine.
aCheck for leaks (see 62A, Air conditioning, Refrig-
erant circuit: Check, page 62A-7) .
aCheck that the air conditioning system is operating
correctly (see 62A, Air conditioning, Air condi-
tioning: Check, page 62A-4) .
143882

62A-33
AIR CONDITIONING
Compressor - condenser connecting pipe: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDrain the refrigerant circuit using a refrigerant
charging station (see 62A, Air conditioning, Re-
frigerant circuit: Draining - Filling, page 62A-8) .
aDisconnect the battery (see ) (80A, Battery).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the pressure sensor connector (1) . Equipment required
refrigerant charging station
compressed air nozzle
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair:
- (see 62A, Air conditioning, Air conditioning:
Precautions for the repair, page 62A-1) ,
- (see Vehicle: Precautions for the repair) (01D,
Mechanical introduction).
Note:
Use blanking plugs for the fuel circuits with part no.
77 01 208 229 or 77 01 476 857 to plug any open-
ings exposed to the open air. They must be clean.
Do not use any which have already been used to
plug a fuel circuit.
WARNING
Consult the device's operating manual to avoid
incorrect use.
121174

62A-36
AIR CONDITIONING
Compressor - condenser connecting pipe: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aConnect the battery (see ) (80A, Battery).
aConsult the refrigerant and oil quantity values before
filling the circuit (see 62A, Air conditioning, Air
conditioning: Parts and consumables for the re-
pair, page 62A-2) .
aFill the refrigerant circuit using a refrigerant charg-
ing station (see 62A, Air conditioning, Refriger-
ant circuit: Draining - Filling, page 62A-8) .
aCheck for leaks (see 62A, Air conditioning, Refrig-
erant circuit: Check, page 62A-7) .
aCheck that the air conditioning system is operating
correctly (see 62A, Air conditioning, Air condi-
tioning: Check, page 62A-4) .

62A-37
AIR CONDITIONING
Compressor - intermediate pipe connecting pipe: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDrain the refrigerant circuit using a refrigerant
charging station (see 62A, Air conditioning, Re-
frigerant circuit: Draining - Filling, page 62A-8) .
aDisconnect the battery (see ) (80A, Battery).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the « expansion valve - intermediate
pipe » (1) connecting pipe on the « compressor - in-
termediate pipe » connecting pipe using the (Mot.
1410). Special tooling required
Mot. 1410Set of refrigerant pipe union
disconnection sockets.
(dimensions in inches): 5/16,
3/8, 1/2, 5/8, 3/4, 7/8.
Equipment required
refrigerant charging station
compressed air nozzle
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair:
- (see 62A, Air conditioning, Air conditioning:
Precautions for the repair, page 62A-1) ,
- (see Vehicle: Precautions for the repair) (01D,
Mechanical introduction).
Note:
Use blanking plugs for the fuel circuits with part no.
77 01 208 229 or 77 01 476 857 to plug any open-
ings exposed to the open air. They must be clean.
Do not use any which have already been used to
plug a fuel circuit.
WARNING
Consult the device's operating manual to avoid
incorrect use.
121180

62A-39
AIR CONDITIONING
Compressor - intermediate pipe connecting pipe: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
aClean the surface and seal of the pipe using EN-
GINE CLEANER (see Vehicle: Parts and con-
sumables for the repair) (04B, Consumables -
Products).
aUse a compressed air nozzle to blow on the sur-
face and the seal of the connecting pipe.
aLubricate the surface of the connecting pipe and the
seal with air conditioning oil (see 62A, Air condi-
tioning, Air conditioning: Parts and consum-
ables for the repair, page 62A-2) .
aRemove the blanking plugs.II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the « compressor - intermediate pipe » con-
necting pipe.
aFit the « compressor - intermediate pipe » connect-
ing pipe on the compressor.
aRefit:
-the bolt on the « compressor - intermediate pipe »
connecting pipe on the compressor,
-the bolt on the « compressor - intermediate pipe »
connecting pipe bracket on the compressor.
aCouple the « expansion valve - intermediate pipe »
connecting pipe to the « compressor - intermediate
pipe » connecting pipe.
III - FINAL OPERATION
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aConnect the battery (see ) (80A, Battery).
aConsult the refrigerant and oil quantity values before
filling the circuit (see 62A, Air conditioning, Air
conditioning: Parts and consumables for the re-
pair, page 62A-2) .
aFill the refrigerant circuit using a refrigerant charg-
ing station (see 62A, Air conditioning, Refriger-
ant circuit: Draining - Filling, page 62A-8) .
aCheck for leaks (see 62A, Air conditioning, Refrig-
erant circuit: Check, page 62A-7) .
aCheck that the air conditioning system is operating
correctly (see 62A, Air conditioning, Air condi-
tioning: Check, page 62A-4) .
143880
143882

62A-40
AIR CONDITIONING
Pressure sensor: Removal - Refitting
AIR CONDITIONING or CLIMATE CONTROL
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the pressure sensor connector (1) .
aRemove the pressure sensor.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the pressure sensor.
aConnect the pressure sensor connector.
II - FINAL OPERATION.
aRemove:
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres).
121174
Note:
An automatic shut-off valve isolates the circuit
from the outside during removal; do not drain the
refrigerant from the circuit.