warning lights RENAULT TWINGO 2009 2.G Chasiss ABS Workshop Manual

38C-9
MR-413-X44-38C000$188_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Function
EBD (electronic braking distribution):
The EBD optimises the brakeforce distribution between the front and rear axles. This function ensures vehicle
stability under braking.
ABS (anti-lock braking system):
The ABS prevents the wheels from locking when braking. This function allows the vehicle to be steered under
braking and ensures vehicle stability under braking.
MSR (engine torque control):
This is a function that enhances the ABS function. It prevents the drive wheels from spinning excessively when lifting
off the accelerator or changing down a gear on a low grip surface, by allowing the engine to regulate the driving
torque of the engine (resisting torque compensation) to "relaunch" the wheels.
The system also supplies the other computers with information on the vehicle speed via a wire connection for the
radio, the power steering and the electric sunroof, and via the multiplex network for the other computers. The ABS
computer supplies the multiplex network with the odometry for the instrument panel and navigation system. If heavy
braking produces very rapid deceleration, the ABS computer sends out a request to the UCH (passenger
compartment connection unit) via the multiplex network to ask it to switch on the hazard warning lights (depending
on the law in the relevant country).
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$188_eng.mif

38C-11
MR-413-X44-38C000$282_eng.mif
V1
38C
ANTI-LOCK BRAKING SYSTEM
Fault finding - Defect and safe modes
Fault finding warning lights programming
Instrument panel warning lightInstrument panel
messageMeaning
Brake faultsABS system STOPNo computer.
ABS flashing
at 8 Hz
(quickly)Tachometric index not
programmed.
ABS flashing
at 8 Hz
(quickly)SERVICETachometric index not
programmed and
versions not
programmed.
Brake faults
flashing at
2 HzABS flashing
at 2 Hz
(slowly)No messageABS computer is in fault
finding mode.
ABS system SERVICE Check the ABS ABS fault.
Brake faultsABS system SERVICE STOP Braking system fault EBD fault.
Note:
The STOP warning light is always accompanied by a single audible warning (1 beep).
MK70 ABS
Vdiag No: 04
MR-413-X44-38C000$282_eng.mif

38C-39
MR-413-X44-38C000$517_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
MK70 ABS
Vdiag No: 04
38C
DF098
PRESENT
OR
STOREDNO UCH MULTIPLEX SIGNAL
NOTESSpecial notes:
Even though it is stored in the computer, this fault does not cause the warning lights to
come on or a fault message, because the ABS system is not faulty.
Perform fault finding on the UCH (Passenger compartment connection unit) using the
diagnostic tool.
Note:
After repairing the fault in the UCH (Passenger compartment connection unit),
clear the fault memory in the ABS system.
Priority in the event of a number of faults:
Deal with fault DF152 Multiplex network
first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Check the UCH (Passenger compartment connection unit) using the diagnostic tool.
Run a multiplex network test (see 88B, Multiplex).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_DF098

38C-50
MR-413-X44-38C000$517_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
MK70 ABS
Vdiag No: 04
38C
DF311
PRESENT
OR
STOREDNO BVR MULTIPLEX SIGNAL
NOTESSpecial notes:
Even though it is stored in the computer, this fault does not cause the warning lights to
come on or a fault message, because the ABS system is not faulty.
Perform fault finding on the BVR (sequential gearbox) using the diagnostic tool.
Note:
After repairing the fault in the BVR (sequential gearbox), clear the fault memory
in the ABS system.
Priority in the event of a number of faults:
Deal with fault DF152 Multiplex network first if it is present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Check the gearbox type configuration with the diagnostic tool, using command LC008 Gearbox type.
If the configuration is not correct, configure the gearbox type present on the vehicle using configuration command
CF079 Gearbox type.
Check the BVR (sequential gearbox) using the diagnostic tool.
Run a multiplex network test (see 88B, Multiplex).
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_DF311