radiator RENAULT TWINGO 2009 2.G Chasiss Workshop Manual

Contents
Radiator mounting cross
member: Removal - Refitting 31A-51
Front anti-roll bar: Removal -
Refitting 31A-52
33A REAR AXLE COMPONENTS
Rear brake pads: Removal -
Refitting 33A-1
Rear brake hose: Removal -
Refitting 33A-4
Rear brake calliper: Removal
- Refitting 33A-7
Rear brake calliper
mounting: Removal -
Refitting 33A-9
Rear brake disc: Removal -
Refitting 33A-11
Rear brake disc: Description 33A-13
Rear brake lining: Removal -
Refitting 33A-14
Rear brake cylinder:
Removal - Refitting 33A-17
Rear brake drum: Removal -
Refitting 33A-19
Rear brake drum:
Description 33A-21
Rigid brake pipe: Removal -
Refitting 33A-22
Shock absorber: Removal -
Refitting 33A-24
Rear suspension spring:
Removal - Refitting 33A-28
Rear drum bear ing: Removal
- Refitting 33A-30
Rear stub axle carr ier:
Removal - Refitting 33A-32
Complete rear axle system:
Removal - Refitting 33A-37 31A FRONT AXLE COMPONENTS
35A WHEELS AND TYRES
Wheel: Removal - Refitting 35A-1
Wheel: Balancing 35A-4
Tyres: Identification 35A-7
Tyres: Removal - Refi tting 35A-8
Tyre pressure: Identification 35A-10
Wheel r im: Identifi cation 35A-11
36A STEERING ASSEMBLY
Steering box: Removal -
Refitting 36A-1
Track rod: Removal -
Refitting 36A-2
Axial ball joint linkage:
Removal - Refitting 36A-4
Steering column: List and
location of components 36A-6
Steering column: Removal -
Refitting 36A-7
Steering box gaiter: Removal
- Refitting 36A-16
Bulkhead seal: Removal -
Refitting 36A-17
Intermediate shaft: Removal
- Refitting 36A-18
Steering column adjustment
handle: Removal - Refitting 36A-21
Steering wheel: Removal -
Refitting 36A-23
36B POWER ASSISTED STEERING
Power-assisted steering
computer: Removal -
Refitting 36B-1

31A-46
FRONT AXLE COMPONENTS
Front axle subframe: Removal - Refitting
31A
-the subframe tie-rod bolts (10) ,
-the subframe tie-rods.
aRemove:
-the rear suspended engine mounting (11) (see
Lower engine tie-bar: Removal - Refitting) (19D,
Engine mounting),
-the acoustic tie-rod bolts (12) ,
-the acoustic tie rods.
aPosition the (Mot. 1390).
aRemove the left-hand tie-rod bolt (13) .aAttach the cooling radiator to the upper cross mem-
ber.
aRemove:
-the bolts (14) from the front end cross member,
-the subframe bolts (15) ,
-the « subframe - front driveshaft lower arm - steer-
ing box - front anti-roll bar » assembly with the
(Mot. 1390).
119335
132029
119336
Note:
This operation requires two people.

31A-48
FRONT AXLE COMPONENTS
Front axle subframe: Removal - Refitting
31A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the speed selection cable guide on the sub-
frame.
aRefit:
-the front driveshaft lower arms (see 31A, Front
axle components, Front driveshaft lower arm:
Removal - Refitting, page 31A-33) ,
-the front anti-roll bar (see 31A, Front axle compo-
nents, Front anti-roll bar: Removal - Refitting,
page 31A-52) ,
-the steering box (see 36A, Steering assembly,
Steering box: Removal - Refitting, page 36A-1) .
aRefit the « subframe - front driveshaft lower arm -
steering box - front anti-roll bar » assembly with the
(Mot. 1390).
aTighten to torque:
-the rear subframe bolts (105 Nm) (20) ,
-the front subframe bolts (62 Nm) (22) ,
-the front end cross member bolts (21 Nm) (21) .aRefit:
-the rear suspended engine mounting (see Lower
engine tie-bar: Removal - Refitting) (19D, En-
gine mounting),
-the acoustic tie rods.
aTighten to torque:
-the acoustic tie-rod bolts (21 Nm) (23) ,
-the acoustic tie-rod bolts (90 Nm) (24) .
aRefit the sub-frame tie-rods.
aTighten to torque:
-the subframe tie-rod bolts (21 Nm),
-the subframe tie-rod nuts (62 Nm).
aCheck the position of the gear selection cables in the
guide.
aFit the gearbox control gear lever arm.
aTorque tighten the gear lever arm nut (28 Nm).
aFit the gear lever arm rubber protector. K9K
Note:
Be careful with the guide of the lower or upper
radiator when fitting the subframe. There is a risk
of the radiator guides breaking.
119336
119335
K9K
JB1

31A-51
FRONT AXLE COMPONENTS
Radiator mounting cross member: Removal - Refitting31A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the front bumper ( (see Front bumper: Re-
moval - Refitting) ).
aAttach the radiator upper section.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the bolts (1) ,
-the radiator mounting cross member.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the radiator mounting cross member,
-the bolts (1) .
aTorque tighten the radiator mounting cross mem-
ber bolts (44 Nm).II - FINAL OPERATION.
aDetach the radiator upper section.
aRefit the front bumper ( (see Front bumper: Re-
moval - Refitting) ). Tightening torquesm
radiator mounting cross
member bolts44 Nm
121040