instrument panel RENAULT TWINGO 2009 2.G Electrical Equipment - Airbags And Pretensioners Workshop Manual

88C-6
MR-413-X44-88C000$077.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - Introduction88C
5. FAULT FINDING LOG
You will always be asked for this log:
●when requesting technical assistance from Techline,
●for approval requests when replacing parts for which approval is mandatory,
●to be attached to monitored parts for which reimbursement is requested. The log is needed for warranty
reimbursement, and enables better analysis of the parts removed
.
6. SAFETY INSTRUCTIONS
Safety rules must be observed during any work on a component to prevent any damage or injury:
Check the battery voltage to avoid incorrect operation of computer functions.
During work on the airbag/seat belt pretensioner systems, it is vital that you lock the computer using the
diagnostic tool to prevent any risk of accidental triggering (all the trigger lines will be disabled).
The locked mode is indicated when the instrument panel warning light comes on.
If it is impossible to connect the diagnostic tool, switch off the ignition, remove the system power supply
fuse and wait at least 2 seconds for the discharge of the reserve power capacity.
Never measure the airbag or pretensioner trigger lines with any device other than XRBAG or CLIP's "Airbag
and pretensioner wiring harness check".
Before using a dummy ignition module, ensure that its resistance is between 1.8 and 2.5 Ω.
During the procedure, check that the computer feed voltage does not drop below 10 V.
Disconnect the battery before removing and refitting any pyrotechnic component (airbag module,
pretensioner or seat belt retractor).IMPORTANTIMPORTANT
Any fault on a complex system requires thorough fault finding with the appropriate tools. The
FAULT FINDING LOG, which should be completed during the procedure, enables you to keep
track of the procedure which is carried out. It is an essential document when consulting the
manufacturer.
IT IS THEREFORE ESSENTIAL THAT THE FAULT FINDING LOG
IS FILLED OUT EVERY TIME IT IS REQUESTED BY TECHLINE OR THE WARRANT RETURNS
DEPARTMENT.
IMPORTANT
Airbag and pretensioner destruction and scrapping is subject to national legislation.

88C-8
MR-413-X44-88C000$154.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - List and location of components88C
Version 10 trigger lines (continued)
Number Description
1Driver's frontal airbag
2Passenger frontal airbag
3Side chest-level airbag (passenger or driver)
4Rear curtain airbag (passenger or driver)
5Rear seat belt pyrotechnic retractor
6Lap belt pyrotechnic pretensioner (passenger and driver)
7Airbag computer
8Driver's seat belt buckle sensor
9Side impact sensor (passenger or driver)
10 Sensor for front passenger airbag inhibition by key
11 Instrument panel
12 Information to other systems (transmission via CAN)
(*) Component which can be deactivated by key

88C-10
MR-413-X44-88C000$154.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - List and location of components88C
Version: 6 trigger lines (continued)
Number Description
1Driver's frontal airbag
2Passenger frontal airbag
3Side chest-level airbag (passenger or driver)
4Lap belt pyrotechnic pretensioner (passenger or driver)
5Airbag computer
6Driver's seat belt buckle sensor
7Side impact sensor (passenger or driver)
8Instrument panel
9Sensor for front passenger airbag inhibition by key
10 Information to other systems (transmission via CAN)
(*) Component which can be deactivated by key

88C-12
MR-413-X44-88C000$154.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - List and location of components88C
Version: 4 trigger lines (continued)
Number Description
1Driver's frontal airbag
2Passenger frontal airbag
3Lap belt pyrotechnic pretensioner (passenger or driver)
4Airbag computer
5Driver's seat belt buckle sensor
6Sensor for front passenger airbag inhibition by key
7Instrument panel
8Information to other systems (transmission via CAN)
(*) Component which can be deactivated by key (according to fault finding configuration)

88C-16
MR-413-X44-88C000$308.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Function
The MRSZ airbag computer takes control of all of the vehicle's restraint devices intended to ensure the protection of
the occupants (driver, front and rear passengers).
The MRSZ computer is designed to carry out the following functions:
●detection and confirmation of longitudinal impacts (front or rear) and/or side impacts,
●corresponding activation of the pyrotechnic restraint devices (e.g.: pretensioner, airbag),
●management of the different signals relating to the characteristics of the occupants (e.g.: presence detection),
●management of the function inhibiting the trigger lines and the passenger sensor,
●management and surveillance of the instrument panel "Airbag Fault" and "Airbag Off" warning lights via the
CAN network,
●activation of the "Crash output" signal via the CAN in the event of a crash,
●management of the fault finding signals (signals provided by the fault manager in response to fault finding
requests, whether this consists of internal faults or input/output fault finding).
Special notes:
–Frontal impacts:
This function is carried out using the MRSZ accelerometer. Accelerometers measure the violence of the impact. The
vehicle speed, the position of the passenger airbag locking switch and the accelerometer measurements determine
the strategy that the computer adopts to trigger the ignition modules. The front seat belt buckle pretensioners and
the front airbag may also be triggered or not depending on the input parameters.
–Side impacts:
This function is carried out by the MRSZ computer and the side impact sensors, if fitted.
The position of the passenger airbag locking switch and the accelerometer measurements determine the strategy
that the computer adopts to trigger the ignition modules. The front buckle pretensioners and the front chest-level
airbags and curtain airbags may also be triggered or not.
–Inhibition of passenger trigger lines:
This function is managed by the airbag computer, according to the position of the passenger airbag inhibition switch
and depending on the vehicle context.
The change in status of the inhibition switch must be done outside of after ignition feed. A change in status of the
switch is, however, authorised for 10 seconds after the after ignition feed for the vehicle is switched on.
If a change is status occurs outside of this 10 seconds, the computer will register a fault.
Inhibition programming:
–Trigger lines inhibited and "Airbag Off" warning light lit if switch is on "OFF" 100 Ω.
–Trigger lines authorised if the switch is on "ON" 400 Ω.
–Trigger lines inhibited, "Airbag Fault" and "Airbag Off" warning lights lit if a fault is detected, if the switch is not
configured and detected as present, or if there is a change of position outside of the conditions
MR-413-X44-88C000$308.mif
MRSZ AIRBAG
Vdiag: 04

88C-17
MR-413-X44-88C000$308.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - Function88C
By default, when the key is in the inhibition position, the following protections and signals are inhibited in the event of
a crash:
–Passenger front air bag.
–Passenger chest-level airbag, if fitted.
The passenger front airbag and passenger chest-level airbag are inhibited when the locking switch is
positioned on OFF or when DF028 "PASSENGER AIRBAG STATUS INDICATOR LIGHT CIRCUIT" or DF193
"PASSENGER AIRBAG LOCKING STATUS CHANGE" is present in the computer memory.
–Seat belt locking monitoring:
This function is carried out by the instrument panel (seat belt reminder indicator light and buzzer). The MRSZ
computer only sends the driver's seat belt buckle sensor status.
An instrument panel warning light indicates that the seat belt is not being worn by the driver and a beep sounds as a
reminder when the vehicle speed exceeds 12 mph (20 km/h).
–Monitoring the information displayed on the instrument panel:
The instrument panel controls the correct operation of the "Airbag fault" and "Airbag OFF" warning lights and
informs the airbag computer, via the multiplex network, of any possible malfunctions in the warning light circuits.

88C-18
MR-413-X44-88C000$385.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Replacement of components
REPLACING A SYSTEM COMPONENT
Disconnect the battery before removing and refitting any pyrotechnic component (airbag module,
pretensioner or seat belt retractor).
The computer must always be locked before any operation on a system component.
REPLACING THE AIRBAG COMPUTER
BEFORE REPLACING THE COMPUTER IT IS ESSENTIAL THAT YOU CONTACT THE TECHLINE.
To ensure that the returned computer's fault can be analysed, do not use command RZ001 "FAULT
MEMORY" when DF001 "COMPUTER" is present or stored.
The airbag computers are sold in locked mode to avoid all risk of accidental triggering (all trigger lines are inhibited).
The "locked" mode is indicated when the airbag fault warning light on the instrument panel lights up.
Follow this procedure to replace an airbag computer:
–check that the ignition is switched off,
–replace the computer,
–modify the computer configuration if necessary,
–enter the VIN into the computer with the diagnostic tool using command VP010 "WRITE VIN",
–switch off the ignition,
–carry out a check using the diagnostic tool,
–unlock the computer with command VP007 "UNLOCK COMPUTER", only if there are no faults indicated by the
diagnostic tool and check that the indicator light has gone out.
MR-413-X44-88C000$385.mif
MRSZ AIRBAG
Vdiag: 04

88C-21
MR-413-X44-88C000$539.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Fault summary table
Tool faultAssociated
DTCDiagnostic tool title
DF0019080 Computer
DF0029042 Computer feed voltage
DF0039007 Driver's frontal airbag circuit
DF0049005 Passenger's front airbag circuit
DF0289041 Passenger airbag status warning light circuit
DF034907E Computer locked
DF0399035 Driver's side sensor circuit
DF0409036 Passenger's side sensor circuit
DF0609050 Multiplex network
DF068900C Passenger's chest front side airbag circuit
DF069900A Passenger side curtain airbag circuit
DF0709009 Driver's side curtain airbag circuit.
DF077900B Driver's front side chest airbag circuit
DF0919034 Airbag locking switch circuit
DF1659040 Airbag fault warning light circuit
DF1839012 Driver's side front buckle pretensioner circuit
DF1849013 Passenger side front buckle pretensioner circuit
DF193907C Passenger airbag locking status change.
DF194907F Computer to be replaced following impact
DF2329051 Driver's seat belt buckle sensor circuit
DF242907B Left-hand/right-hand drive configuration
DF2629050 Vehicle speed multiplex signal
DF2639050 No ABS/ESP multiplex signal
DF2649050 No instrument panel multiplex signal
MR-413-X44-88C000$539.mif
MRSZ AIRBAG
Vdiag: 04

88C-28
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF028
PRESENT
PASSENGER AIRBAG STATUS WARNING LIGHT CIRCUIT
NOTESSpecial notes:
This fault may be "present" after command AC009 Instrument panel warning lights
is activated on the instrument panel.
Apply the fault finding procedure relevant to this fault in the instrument panel fault finding information section.
Carry out a fault finding procedure on the instrument panel (see 83A, Instrument panel).
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat a check using the diagnostic tool and, if there are no faults (do not take the
DF034 "Computer locked'' into account), unlock the computer using the command
VP007 ''Unlock computer''.
ABGMRSZ_V04_DF028P

88C-34
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF060
PRESENT
MULTIPLEX NETWORK
1.DEF: Multiplex network
2.DEF: Initialisation of instrument panel too long
NOTESNone.
Carry out the fault finding procedure for the multiplex network.
Run a multiplex network test (see 88B, Multiplexing).
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat a check using the diagnostic tool and, if there are no faults (do not take the
DF034 "Computer locked'' into account), unlock the computer using the command
VP007 ''Unlock computer''.
ABGMRSZ_V04_DF060P