fuse chart RENAULT TWINGO 2009 2.G Electrical Equipment - Electric Windows, Sunroof Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 54, PDF Size: 0.25 MB
Page 9 of 54
87D-9
MR-413-X44-87D000$472_eng.mif
V1
87D
ELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart
ALP 1 No electric window operation
Applies to:Driver and passenger electric windows
Left-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Check that the fuses are sound.
Use a 21 W test light.
Remove the driver's window switch (see MR 411
mechanical systems, 87D, Electric windows -
Sunroof, driver's door front electric window
switch: Removal - Refitting) and disconnect its
connector.
Connect a test light between connection SPB3
and the earth MAM of component 1512. Pay
close attention to the intermediate connector.
Does the test light illuminate?
YES
Shunt connection SPB3 with 21A and MAM with
21B to lower the window (to raise the window
SPB3 with 21B and 21A with MAM), on the
connector of component 1512.
Does the window move?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder
switch: Removal - Refitting).
Connect the test light between
connection SPB3 and the chassis
earth.
Does the test light illuminate?
YES
Check that the earth MAM of
component 1512 is correctly mounted
on the chassis. If the earth is faulty,
clean and retighten it.
Otherwise the fault is caused by the
wiring; if there is a repair procedure
(see Technical Note 6015A,
Repairing electrical wiring, W iring:
Precautions for repair), repair the
wiring; if not, replace it.NO
NO
NO
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
AB
New Twingo
MR-413-X44-87D000$472_eng.mif
Page 11 of 54
87D-11
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 1 No electric window operation
Applies to:Driver and passenger electric windows
Right-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Check that the fuses are sound.
Use a 21 W test light.
Remove the driver's window winder switch (see
MR 411 mechanical systems, 87D, Electric
windows - Sunroof, Driver's door
front window winder switch: Removal -
Refitting) and disconnect its connector.
Connect a test light between connection SPB3
and the earth MAN of component 1512. Pay
close attention to the intermediate connector.
Does the test light illuminate?
YES
Shunt connection SPB3 to 21A and MAN to 21B
to lower the window (to raise the window SPB3 to
21B and 21A to MAN), on the connector of
component 1512.
Does the window move?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder
switch: Removal - Refitting).
Connect the test light between
connection SPB3 and the chassis
earth.
Does the test light illuminate?
YES
Check that the earth MAN of
component 1512 is correctly mounted
on the chassis. If the earth is faulty,
clean and retighten it.
Otherwise the fault is caused by the
wiring; if there is a repair procedure
(see Technical Note 6015A,
Repairing electrical wiring, W iring:
Precautions for repair), repair the
wiring; if not, replace it.
NO
NO
NO
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
AB
Page 21 of 54
87D-21
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 5 Only the driver's window does not operate at all
Applies to:Driver's one-touch electric windows and passenger's
electric window
Left-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged, + after ignition feed switched
on and doors closed.
Check that the fuses are sound.
Using a 21 W test bulb and a multimeter.
Remove the driver's window winder switch (see
MR 411 mechanical, 87D Electric windows -
Sunroof, driver's door
front window winder switch: Removal -
Refitting) and disconnect its connector.
Shunt connection 21E to MAM to lower the
window (to raise it, shunt 21C to MAM) on the
connector of component 1512.
Does the window move?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder
switch: Removal - Refitting).
NOUsing an ohmmeter, carry out a continuity
test on connection MAM between
component 1512 and the chassis earth.
Is the earth correct?
YES NO
NOCheck that earth MAM is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it.
Otherwise the fault is caused by the wiring;
if there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring; if not, replace it.
Check for an earth on connection MAM of
component 203
Is the earth correct?
YES
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
A
Page 24 of 54
87D-24
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 5 Only the driver's window does not operate at all
Applies to:Driver's one-touch electric windows and passenger's
electric window
Right-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged, + after ignition feed switched
on and doors closed.
Check that the fuses are sound.
Using a 21 W test bulb and a multimeter.
Remove the driver's window winder switch (see
MR 411 mechanical, 87D Electric windows -
Sunroof, driver's door
front window winder switch: Removal -
Refitting) and disconnect its connector.
Shunt connection 21E to MAN to lower the
window (to raise it, shunt 21C to MAN) on the
connector of component 1512.
Does the window move?
YES
Replace the driver's window winder switch (see
MR 411 mechanical, 87D, Electric windows -
Sunroof, Driver's door front window winder
switch: Removal - Refitting).
NOUse an ohmmeter to test the continuity on
connection MAN between component 1512
and the chassis earth.
Is the earth correct?
YESNO
NOCheck that earth MAN is correctly mounted
on the chassis. If the earth is faulty, clean and
retighten it.
Otherwise the fault is caused by the wiring;
if there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring; if not, replace it.
Check for earth on connection MAN of
component 203.
Is the earth correct?
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
A
YES
Page 29 of 54
87D-29
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
Continuity fault on connection SPB3. Pay
attention to the intermediate connector. If
there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
ALP 7 The passenger window does not operate at all with any switch
Applies to:Driver's one-touch electric windows and passenger's
electric window
Left-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Check that the fuses are sound.
Use a 21 W test light.
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting) and disconnect its
connector.
Use the test light connected to the chassis earth
to check the feed on connections 22D and 22C
on component 133.
Are the feeds correct?
YES
Shunt connection 22B to MAN and 22A to 22C
to lower the window (to raise it, shunt 22A to
MAN and 22B to 22D), on the connector of
component 133.
Does the window move?
YES
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting).
NORemove the driver's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof, driver's door front
window winder switch: Removal -
Refitting) and disconnect its connector.
Use a test light connected to the chassis
earth to check the feed on connection SPB3
of component 1512.
Is the feed correct?
NO
NOYES
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
BA
Page 31 of 54
87D-31
MR-413-X44-87D000$472_eng.mif
V1
New TwingoELECTRIC WINDOWS - SUNROOF
Electric windows - Fault finding chart87D
ALP 7 The passenger window does not operate at all with any switch
Applies to:Driver's one-touch electric windows and passenger's
electric window
Right-hand drive vehicle
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Check that the fuses are sound.
Use a 21 W test light.
Remove the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting) and disconnect its
connector.
Use the test light connected to the chassis earth
to check the feed on connections 22D and 22C
on component 133.
Are the feeds correct?
YES
Shunt connection 22B to MAM and 22A to 22C
to lower the window (to raise the window
shunt 22A to MAM and 22B to 22D), on
connector of component 133.
Does the window move?
YES
Replace the passenger's window winder switch
(see MR 411 mechanical, 87D Electric
windows - Sunroof, passenger's
door front window winder switch:
Removal -Refitting).
NORemove the driver's window winder switch
(see MR 411 mechanical, 87D, Electric
windows - Sunroof, driver's door front
window winder switch: Removal -
Refitting) and disconnect its connector.
Use a test light connected to the chassis
earth to check the feed on connection SPB3
of component 1512.
Is the feed correct?
NO
NOContinuity fault on connection SPB3. Pay
attention to the intermediate connector. If
there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it.
YES
AFTER REPAIRCheck that the electric windows are operating correctly; if not, run fault finding
(see Customer complaints).
BA
Page 43 of 54
87D-43
MR-413-X44-87D000$944_eng.mif
V1
87D
ELECTRIC WINDOWS - SUNROOF
Electric sunroof - Fault finding chart
ALP 1 The sunroof does not operate at all
NOTESUse Wiring Diagram Technical Note, New Twingo.
Carry out the various checks with the battery charged and + after ignition feed
switched on.
Check that the fuses are sound.
Use a multimeter and a 21 W test bulb.
Use the diagnostic tool.
Read the configuration in the UCH and check
that configuration LC070 “One touch
window\sunroof” * is correctly configured
“with”.
Does parameter LC070 display WITH?
YES
Move the sunroof control to the “Closed”
position and press and hold the central part of
the control.
After pressing the central part of the control
for approximately 10 seconds, does the roof
move smoothly?
YES
See ALP 4.
NOModify the configuration (see 87B,
Passenger compartment connection unit).
NOCheck the feed by connecting a test light between
connections BP93 and MAM of component 1579.
Does the bulb light up correctly?
YES NO
Check the feed by connecting a test light
between connection BP93 and the chassis earth.
Does the test light work
correctly?
NO YES
Fault on connection MAM between
component 1579 and the chassis earth; be
careful of the intermediate connector R339.
If there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it. When the wiring has
been repaired, carry out the initialisation (see
Electric sunroof: Initialisation).
Fault on connection BP93 between
components 1579 and 1016; be careful of the
intermediate connectors R339 and R301.
If there is a repair procedure (see Technical
Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the
wiring, otherwise replace it. After the wiring has
been repaired, carry out an initialisation (see
Electric sunroof: Initialisation).
A
New Twingo
MR-413-X44-87D000$944_eng.mif