ABS RENAULT TWINGO 2009 2.G Electrical Equipment - Instrument Panel User Guide

83A-41
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET248
STOP WARNING LIGHT ACTIVATED BY THE SYSTEM
If the STOP WARNING LIGHT is illuminated, check for faults and check the conformity of the systems
concerned.
1 : Injection
2 : Coolant temperature
3 : Oil pressure
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
4 : Brake fluid level
See the interpretation of ET019 MINIMUM BRAKE FLUID LEVEL.
5 : Electronic Braking Distribution
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
6 : Electric power assisted steering
Carry out fault finding on the EPAS system (see 36B, Power-assisted steering).
7 : Battery charge
Carry out fault finding on the charging circuit (see Technical Note 6014A, Checking the charging circuit).
If there are no faults, carry out a multiplex network check (see 88B, Multiplex).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET248 / TDB_V08_ET248

83A-42
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET249
SERVICE WARNING LIGHT ACTIVATED BY THE SYSTEM
If the SERVICE WARNING LIGHT is illuminated, check for faults and check the conformity of the systems
concerned.
1 : Multiplex line communication
Check the multiplex network (see 88B, Multiplex)
2 : Injection
3 : Water present in diesel fuel
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
4 : Sequential gearbox
Carry out fault finding on the sequential gearbox (see 23A, Sequential gearbox).
5 : Vehicle speed circuit
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
6 : Cruise control/speed limiter
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
7 : ESP
8 : ABS
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
9 : Oil service interval
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
10 : Particle filter
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
11 : Airbag
Carry out fault finding on the Airbag system (see 88C, Airbag and pretensioners).
12 : OBD
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
If there are no faults, carry out a multiplex network check (see 88B, Multiplex).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET249 / TDB_V08_ET249

83A-54
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 2
CONTINUED 2
Check the continuity, insulation and absence of
interference resistance on the following
connections:
•41A between components 247 and 833,
•41B between components 247 and 833.
Are the checks correct?
Measure the resistance of the sender and the wiring
using a multimeter via the connector, on the
instrument panel side.
Is the value measured and the value provided by
the CLIP tool the same as or approximately
± 5 ΩΩ Ω Ω
?Contact the Techline.
Replace the instrument panel, component code 247
(see MR 411, Mechanical, 83A, Instrument panel,
Instrument panel: Removal - Refitting).
Is the fault still present?The problem disappears.
C
NO
NOD
YES
YES
NO
NO
YES
B

83A-61
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 5
CONTINUED 2
Check the continuity, insulation and absence of interference
resistance on the following connections:
•41A between components 247 and 833,
•41B between components 247 and 833.
Are the checks correct?
If the connection or connections are faulty and there is a repair procedure
(see Technical Note 6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring, otherwise replace the wiring.
Is the fault still present?
The problem disappears.
B
NO
NOC
YES
D
C
NO
YESD
NO

83A-64
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 6
CONTINUED 1
Check the continuity, insulation and absence of interference
resistance on the following connections:
•41A between components 247 and 833,
•41B between components 247 and 833.
Are the checks correct?
If the connection or connections are faulty and there is a repair procedure
(see Technical Note 6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring, otherwise replace the wiring.
Is the fault still present?Contact the Techline.
The problem disappears.
B
NO
NOD
YES
E
D
NO
YES
NO