brake RENAULT TWINGO 2009 2.G Electrical Equipment - Instrument Panel User Guide

83A-38
MR-413-X44-83A000$616.mif
V5

Vdiag No.: 04, 08INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
ET097
PARKING BRAKE
NOTESSpecial notes:
Only apply the checks if the APPLIED and RELEASED statuses are not consistent
with the lever position:
–APPLIED when the lever is released,
–RELEASED when the lever is applied.
APPLIED
STATUS
when lever is
released
Check the connection and condition of the connector of component 156.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the connector, otherwise replace the wiring.
Remove component 156 and check that there is no continuity in “Parking
brake released” position', otherwise replace component 156.
Check the connection and condition of the connector of component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the connector, otherwise replace the wiring.
With the lever released, check that there is no continuity on the following
connection:
Connection 27A between component 156 and the vehicle earth.
With the lever released, check the earth insulation of:
Connection 27A between component 156 and component 247.
If there is a repair method (see Technical Note 6015A Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET097 / TDB_V08_ET097

83A-39
MR-413-X44-83A000$616.mif
V5

Vdiag No.: 04, 08INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
ET097
CONTINUED
RELEASED
STATUS
when the lever
has been
pulled up
Check the connection and condition of the connector of component 156.
Remove the handbrake switch and check the continuity is correct with the
“Parking brake applied” position.
Check the connection and condition of the connector of component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the connector, otherwise replace the wiring.
With the lever pulled, check for continuity on:
Connection 27A between component 156 and the vehicle earth.
With the lever pulled, check the continuity of:
Connection 27A between component 156 and component 247.
If there is a repair method (see Technical Note 6015A Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.

83A-41
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET248
STOP WARNING LIGHT ACTIVATED BY THE SYSTEM
If the STOP WARNING LIGHT is illuminated, check for faults and check the conformity of the systems
concerned.
1 : Injection
2 : Coolant temperature
3 : Oil pressure
Perform fault finding on the injection system:
–Petrol: See 17B, Petrol injection,
–Diesel: See 13B, Diesel injection.
4 : Brake fluid level
See the interpretation of ET019 MINIMUM BRAKE FLUID LEVEL.
5 : Electronic Braking Distribution
Carry out fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
6 : Electric power assisted steering
Carry out fault finding on the EPAS system (see 36B, Power-assisted steering).
7 : Battery charge
Carry out fault finding on the charging circuit (see Technical Note 6014A, Checking the charging circuit).
If there are no faults, carry out a multiplex network check (see 88B, Multiplex).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET248 / TDB_V08_ET248