wiring RENAULT TWINGO 2009 2.G Electrical Equipment - Instrument Panel User Guide

83A-39
MR-413-X44-83A000$616.mif
V5

Vdiag No.: 04, 08INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
ET097
CONTINUED
RELEASED
STATUS
when the lever
has been
pulled up
Check the connection and condition of the connector of component 156.
Remove the handbrake switch and check the continuity is correct with the
“Parking brake applied” position.
Check the connection and condition of the connector of component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the connector, otherwise replace the wiring.
With the lever pulled, check for continuity on:
Connection 27A between component 156 and the vehicle earth.
With the lever pulled, check the continuity of:
Connection 27A between component 156 and component 247.
If there is a repair method (see Technical Note 6015A Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.

83A-40
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET245
INDICATORS
NOTESCheck for the absence of faults on the indicators in the UCH field before starting
fault finding.
Vehicle under + after ignition feed.
If the indicator lights are not displayed or are inconsistent with the position of the control, carry out the following
fault finding procedure.
If status ET245 INDICATORS is INACTIVE and the control is activated:
Check that the connector of component 247 is in good condition and correctly connected.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the connector, otherwise replace the wiring.
Check the continuity of:
Connection 64C between component 645 and component 247 (left-hand indicator)
Connection 64D between component 645 and component 247 (right-hand indicator)
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions
for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET245 / TDB_V08_ET245

83A-49
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
83A
Vdiag No.: 04 08
ALP 1NO COMMUNICATION WITH THE INSTRUMENT PANEL.
The instrument panel does not light up.
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
See Wiring diagram Technical Note, New Twingo.
Test the diagnostic tool on another vehicle which is in perfect working order.
Check that the sensor's green indicator light comes on.
If communication with the second vehicle is impossible, follow the instructions in the CLIP diagnostic tool test
section.
If dialogue with the first vehicle is possible, follow the instructions in the Vehicle check section.
DIAGNOSTIC
TOOL CHECKCheck the cleanliness and condition of the contacts of the diagnostic socket,
component code 225 connected to the vehicle.
Check the condition of the cable from the diagnostic socket to the sensor and the
cleanliness and condition of the connections.
Check the sensor connections.
Check the condition of the cable from the CLIP tool to the sensor as well as the
condition and cleanliness of the connections.
Check the cleanliness and condition of the CLIP socket.
If the connector or connectors are faulty and if there is a repair procedure (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact Techline.
TDB_V04_ALP1/TDB_V08_ALP1
INSTRUMENT PANEL
Fault finding - Fault finding chart

83A-50
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 1
CONTINUED 1
VEHICLE CHECK
Check the cleanliness and condition of the contacts of the diagnostic socket,
component code 225 connected to the vehicle.
Check the condition of the cable from the diagnostic socket to the sensor and the
cleanliness and condition of the connections.
Check the sensor connections.
Check the condition of the cable from the sensor to the CLIP tool and the cleanliness
and condition of the connections.
Check the cleanliness and condition of the CLIP socket.
If the connector or connectors are faulty and if there is a repair procedure (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact Techline.
Check the condition and connection of the instrument panel connector, component
code 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check instrument panel supply fuse MIN (5 A), component code 247 on the passenger
compartment fuse box, component code 1016 and the condition and cleanliness of
the contacts.
Check the instrument panel after ignition supply fuse MIN (15 A), component code
247 on the passenger compartment fuse box, component code 1016, and the
condition and cleanliness of the contacts.

83A-51
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 1
CONTINUED 2
NOTESVehicle under + after ignition feed.
VEHICLE CHECKUse the Universal bornier to check the following connections on the vehicle diagnostic
socket, component code 225:
BP19 "+ protected battery feed" of component 225.
•MAN (if left-hand drive) of component 225.
•MAM (if right-hand drive) of component 225.
•NAM, the earth of component 225.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
Check the earth of connection MAN of the instrument panel, component code 247.
If the earth MAN is poor, check the insulation to + 12 V and check the continuity of
the following connection:
•MAN of component 247.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
Check for + 12 V on connection AP43 and connection BP49 of the instrument panel,
component code 247.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If there is no + 12 V, check the insulation to earth and the continuity of the following
connections:
•AP43 between components 247 and 1016,
•BP49 between components 247 and 1016.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.

83A-52
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 2 The fuel level indicator does not display full
NOTESThe fuel tank must be filled with the ignition switched off (advise the customer to remove
the key).
Ideally the customer must fill the tank with at least 15 litres.
See Wiring diagram Technical Note, New Twingo.
Ask the customer if the tank is filled up under the
following conditions:
–the customer filled the tank up to the 3
rd cut-out
–the customer has changed filling station
–the customer filled the tank in a flat-level station (not
on a slope).
Did the customer fill the tank while observing all of
these conditions?Ask the customer to return just after
having filled the tank under the conditions
mentioned above.
NO
YES
A
TDB_V04_ALP2/TDB_V08_ALP2

83A-54
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 2
CONTINUED 2
Check the continuity, insulation and absence of
interference resistance on the following
connections:
•41A between components 247 and 833,
•41B between components 247 and 833.
Are the checks correct?
Measure the resistance of the sender and the wiring
using a multimeter via the connector, on the
instrument panel side.
Is the value measured and the value provided by
the CLIP tool the same as or approximately
± 5 ΩΩ Ω Ω
?Contact the Techline.
Replace the instrument panel, component code 247
(see MR 411, Mechanical, 83A, Instrument panel,
Instrument panel: Removal - Refitting).
Is the fault still present?The problem disappears.
C
NO
NOD
YES
YES
NO
NO
YES
B

83A-55
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 2
CONTINUED 3
If the connection or connections are faulty and
there is a repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace the wiring.
Is the fault still present?
The problem disappears.
D
NO
YESB
NO

83A-59
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 5Fault with no warning given by warning light (no addition of fuel
since the fault)
NOTESPut the vehicle in + after ignition.
See Wiring diagram Technical Note, New Twingo.
Check the instrument panel warning lights, component
code 247.Replace the instrument panel,
component code 247 (see
MR 411, Mechanical, 83A,
Instrument panel, Instrument
panel: Removal - Refitting). Does the fuel warning light illuminate for 3 seconds when
+ after ignition is switched on?
Record the resistance value provided by the CLIP tool.
Compare the value from the CLIP tool with the warning
resistance, which should be 260 ΩΩ Ω Ω
.
Is this value above or equal to 260 ΩΩ Ω Ω
?Contact the Techline.
Rock the vehicle and check whether the resistance changes by
± 5 ΩΩ Ω Ω
.
Is there a change in the resistance value?Contact the Techline.
NO
YES
YES
NO
YES
NO
A
TDB_V04_ALP5/TDB_V08_ALP5

83A-61
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 5
CONTINUED 2
Check the continuity, insulation and absence of interference
resistance on the following connections:
•41A between components 247 and 833,
•41B between components 247 and 833.
Are the checks correct?
If the connection or connections are faulty and there is a repair procedure
(see Technical Note 6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring, otherwise replace the wiring.
Is the fault still present?
The problem disappears.
B
NO
NOC
YES
D
C
NO
YESD
NO