automatic transmission RENAULT TWINGO 2009 2.G Electrical Equipment - Petrol Injection User Guide

17B-231V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 3
STATUS 3 Clutch pedal depressed
Manual gearbox only:
The cruise control function is deactivated when the gearbox is not coupled to the
engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and the clutch pedal
is depressed.
This deactivates cruise control.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with automatic transmission:
Carry out a multiplex network test, check the configuration of the multiplex network
according to the vehicle's technical specifications and, in particular, the automatic
gearbox computer configuration (see 88B, multiplex).
STATUS 4 Cancel button pressed
The cruise control/speed limiter function is deactivated each time the suspend button
is pressed.
Status ET415 becomes STATUS 4, when driving when:
–Either the cruise control is active, or
–the speed limiter is active
–and when the "0" button is pressed by the driver.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703: Cruise control/speed limiter buttons and run fault
finding on the R/0 control button located on the right-hand side of the steering wheel.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-232V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 4
STATUS 5 Cruise control or speed limiter monitoring
This status appears when the vehicle brakes or decelerates sharply without the
injection computer receiving a signal indicating that the brake pedal switch has
been pressed.
If status ET415 is STATUS 5, consult the interpretation:
–of status ET042 Cruise control/Speed limiter,
–of status ET703 Cruise control/Speed limiter buttons,
–of status ET704 Brake switch no. 1,
–and status ET705 Brake switch no. 2,
to test the cruise control/speed limiter system components and find the defective
component.
Also check the operation of the accelerator pedal, and check for any faults shown
on the diagnostic tool relating to this component. Deal with them if necessary.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 5, deal with any faults that are present or stored
in the injection computer.
If the fault is still present, contact the Techline.
STATUS 6 Gear lever in neutral (manual gearbox) or neutral (automatic transmission).
Status ET415 changes to STATUS 6, when driving, with cruise control active
(ET042) and:
if the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
if the gear lever is in neutral on an automatic transmission.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on
a manual gearbox without declutching, or into neutral on an automatic transmission,
test the ABS computer and check the configuration of the tyre size stored in the
computer. If the configuration is correct, contact the Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-233V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 5
STATUS 7 Lack of correlation between the request and the vehicle speed
Status ET415 becomes STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
This could occur when driving with cruise control active (ET042 Cruise control/
speed limiter: CRUISE CONTROL) and when there is a significant difference
in speed.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001 "Fault memory".
If status ET415 becomes STATUS 7 where the surface is not uneven, contact
the Techline.
STATUS 8 Automatic gearbox in defect mode.
Status ET415 becomes STATUS 8, when driving with cruise control active (ET042)
and if the automatic transmission is in defect mode.
This signal is conveyed on the multiplex line and deactivates the cruise control.
Carry out a multiplex network test, then run fault finding on the automatic
transmission computer.
Deal with any present or stored faults (see 23A, Automatic transmission,
Interpretation of faults).
Clear the automatic transmission computer memory by running command RZ001.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If the specification STATUS 8 is still present, contact Techline.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-241V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET562FAN ASSEMBLY REQUEST BY AUTOMATIC TRANSMISSION (applies only for the sequential gearbox on engine D4F 772)
STATUS
DEFINITIONPRESENT: This status indicates that there has been a fan assembly request from the
transmission.
ABSENT: This status indicates that there has not been a fan assembly request from the
transmission.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
There must be no present or stored faults.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
PRESENT
or
ABSENTThe status is PRESENT or ABSENT depending on the computer program (engine oil
temperature).
SIM32_V44_ET562/SIM32_V4C_ET562/SIM32_V50_ET562/SIM32_V54_ET562
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.