engine coolant RENAULT TWINGO 2009 2.G Electrical Equipment - Petrol Injection Owner's Guide

17B-183V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET039BRAKE PEDAL
STATUS
DEFINITIONDEPRESSED: This status indicates that the brake pedal is in the depressed position.
RELEASED: This status indicates that the brake pedal is in the released position.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
DEPRESSEDStatus ET039 is DEPRESSED when there is pressure on the brake pedal.
In the event of a fault,apply the interpretation of statuses ET704 Brake contact no. 1
and ET705 Brake contact no. 2.
RELEASEDStatus ET039 is RELEASED when there is no action on the brake pedal.
In the event of a fault,apply the interpretation of statuses ET704 Brake contact no. 1
and ET705 Brake contact no. 2.
SIM32_V44_ET039/SIM32_V4C_ET039/SIM32_V50_ET039/SIM32_V54_ET039
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-184V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042CRUISE CONTROL/SPEED LIMITER
STATUS
DEFINITIONNOT DETECTED: This status indicates that the cruise control or speed limiter function
is not present on the vehicle.
INACTIVE: This status indicates that the cruise control/speed limiter main On/Off switch
is in the rest (or neutral) position.
LIMITER: This status indicates that the driver has used the main switch to select the
speed limiter.
CRUISE CONTROL: This status indicates that the driver has used the main switch to
select the cruise control.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Use the Wiring Diagram Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
NOT DETECTEDThe cruise control or speed limiter function is not present on the vehicle.
"INACTIVE"No button has been pressed.
LIMITERThe speed limiter ON/OFF button has been pressed.
Lights the orange warning light on the instrument panel.
CRUISE
CONTROLThe cruise control ON/OFF button has been pressed.
Lights the green warning light on the instrument panel.
SIM32_V44_ET042/SIM32_V4C_ET042/SIM32_V50_ET042/SIM32_V54_ET042
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-189V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET045CRUISE CONTROL/SPEED LIMITER SELECTOR SWITCH ON STEERING WHEEL
STATUS
DEFINITIONRESUME: This status indicates that the R button is pressed.
SUSPEND: This status indicates that the 0 is pressed.
INCREASE: This status indicates that the increase button is pressed.
DECREASE: This status indicates that the decrease button is pressed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
INCREASEStatus ET413 becomes INCREASE when the cruise control + button is pressed.
This button is situated to the left of the steering wheel.
DECREASEStatus ET413 becomes INCREASE when the cruise control + button is pressed.
This button is situated to the left of the steering wheel.
SUSPENDStatus ET413 becomes SUSPEND when the 0 cruise control button is pressed.
This button is situated to the right of the steering wheel.
RESUMEStatus ET413 becomes RESUME when the R cruise control button is pressed.
This button is situated to the right of the steering wheel.
SIM32_V44_ET045/SIM32_V4C_ET045/SIM32_V50_ET045/SIM32_V54_ET045
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-190V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET048ACTUATOR RELAY CONTROL
STATUS
DEFINITIONACTIVE: The status indicates that the control is active.
INACTIVE: The status indicates that the control is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"INACTIVE"
or
ACTIVEThis relay supplies the following actuators: the injectors, the throttle valve control,
the oxygen sensor heating, the bleed solenoid valve, the fuel vapour absorber
and connection 3FB of the injection computer.
In the event of a fault, see the interpretation of fault DF084 Actuator relay control
circuit.
SIM32_V44_ET048/SIM32_V4C_ET048/SIM32_V50_ET048/SIM32_V54_ET048
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-191V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET050ACTUATOR RELAY CONTROL
STATUS
DEFINITIONACTIVE: The status indicates that the canister bleed control is active.
INACTIVE: The status indicates that the canister bleed control is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"INACTIVE"The petrol vapour rebreather bleed does not operate at idle speed.
Use command AC017 Canister bleed solenoid valve to check its operation.
In the event of a fault, see interpretation of fault DF081 Canister bleed solenoid
valve circuit.
SIM32_V44_ET050/SIM32_V4C_ET050/SIM32_V50_ET050/SIM32_V54_ET050
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-192V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET051THROTTLE STOP PROGRAMMING–Completed
–Not completed
STATUS
DEFINITIONDONE: This status indicates that the throttle stop programming has been completed.
NOT DONE: This status indicates that the throttle stop programming has not been
completed.
NOTESThere must be no present or stored faults.
Special notes:
When programming is in progress, the injection system prevents the engine from
starting, until the operation is completed.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
COMPLETED
or
NOT
COMPLETEDThis status does not change according to the ignition or engine status but according
to the programming of the component.
In the event of a fault, program the throttle stops (see Configurations and
programming).
Even though this programming is automatic, take particular care when performing the first motorised throttle stop
programming operation. This can be carried out on several occasions:
–when a computer is switched on for the first time,
–at the end of computer programming (see Configurations and programming).
The air temperature should be greater than 0˚C, during programming, then, at the end of programming, switch off
the ignition and wait 30 seconds for the end of Power Latch so that the computer can store the programmed stops.
SIM32_V44_ET051/SIM32_V4C_ET051/SIM32_V50_ET051/SIM32_V54_ET051
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-193V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET052UPSTREAM O2 SENSOR HEATING
STATUS
DEFINITIONACTIVE: This status indicates that the upstream oxygen sensor heater is active.
INACTIVE: This status indicates that the upstream oxygen sensor heater is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: engine stopped and ignition on.
"INACTIVE"The status is inactive when the engine is off.
In the event of a fault, apply interpretation of DF082 Upstream oxygen sensor
heating circuit.
Conformity check: engine running at idle speed, engine coolant temperature > 80˚C.
"ACTIVE"The status becomes active when the engine is started and its operation increases
according to the heating temperature.
In the event of a fault, apply the interpretation of DF082.
SIM32_V44_ET052/SIM32_V4C_ET052/SIM32_V50_ET052/SIM32_V54_ET052
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-194V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET053DOWNSTREAM O2 SENSOR HEATING
STATUS
DEFINITIONACTIVE: This status indicates that the downstream oxygen sensor heater is active.
INACTIVE: This status indicates that the downstream oxygen sensor heater is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: engine stopped and ignition on.
"INACTIVE"The status is inactive when the engine is off.
In the event of a fault, apply interpretation of DF083 Downstream oxygen sensor
heating circuit.
Conformity check: engine running at idle speed, engine coolant temperature > 80˚C.
"ACTIVE"The status becomes active when the engine is started and its operation increases
according to the heating temperature.
In the event of a fault, apply the interpretation of DF083.
SIM32_V44_ET053/SIM32_V4C_ET053/SIM32_V50_ET053/SIM32_V54_ET053
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-195V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET054IDLING SPEED REGULATION–Active
–Inactive
STATUS
DEFINITIONACTIVE: This status indicates that idle speed regulation is active.
INACTIVE: This status indicates that idle speed regulation is inactive.
NOTESThere must be no present or stored faults.
Special notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: engine stopped and ignition on.
"INACTIVE"The status becomes active when the engine is started.
Conformity check: engine running at idle speed, engine coolant temperature > 80˚C.
ACTIVEThe status becomes active when the engine is started.
SIM32_V44_ET054/SIM32_V4C_ET054/SIM32_V50_ET054/SIM32_V54_ET054
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
Repeat the conformity check from the start.

17B-197V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET056DOUBLE RICHNESS LOOP
STATUS
DEFINITIONACTIVE: The status indicates that the double richness loop is active.
INACTIVE: The status indicates that the double richness loop is inactive.
NOTESThere must be no present or stored faults.
Special notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"INACTIVE"
or
ACTIVEThis status is only inactive if one of the two oxygen sensors is in poor condition.
In the event of a fault, apply the interpretation of faults DF082 Upstream oxygen
sensor heating circuit, DF083 Downstream oxygen sensor heating circuit,
DF092 Upstream oxygen sensor circuit, DF093 Downstream oxygen
sensor circuit.
SIM32_V44_ET056/SIM32_V4C_ET056/SIM32_V50_ET056/SIM32_V54_ET056
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.