battery RENAULT TWINGO 2009 2.G Electrical Equipment - Radio R01-08 User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 91, PDF Size: 0.53 MB
Page 40 of 91
86A-40
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF039
PRESENT
OR
STOREDBATTERY VOLTAGE
1.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
– The + after ignition feed is activated,
– The multimedia system is switched on using the on/off button.
– The battery voltage is out of range (12 V < X < 15 V).
Note:
Apply this fault finding method if the fault reappears as present after having been
cleared
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the conformity of the fuse in the fuse and relay box:
•for New Twingo: F48 (15A),
•for Clio III: F2 (20A) and Unit fuse 710 (15A).
Replace the fuse if not correct.
Disconnect the connector of the radio 261.
Check the continuity of the earth on connection MAO (New Twingo) or MT (Clio III).
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the +12 V supply on connection BCP4 of component 261.
If the supply is not correct, check the insulation, continuity and absence of interference resistance on
connection code BCP4 between components 260 and 261.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R108_VA4_DF039
Page 49 of 91
86A-49V2 MR-413-X44-86A100$130.mif
86A
R01-08
Vdiag No.: A4
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
SupplyPR011:Battery
voltage12 V < X < 15 VIn the event of an
inconsistency, consult the
interpretation of fault DF039
Battery voltage.
R108_VA4_CCONF
RADIO
Fault finding – Conformity check
Page 52 of 91
86A-52V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION (continued)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Front panel button
(continued)ET063:"MEM" buttonPRESSED RELEASED
In the event of an
inconsistency, consult the
interpretation of fault DF055
Button jammed. ET005:Source buttonPRESSED RELEASED
ET007:Traffic info buttonPRESSED RELEASED
ET073:Left-hand buttonPRESSED RELEASED
ET074:Right-hand buttonPRESSED RELEASED
CD ejectionAC013:CD ejectionThis command is used for
testing CD ejection from
the CD player.In the event of an
inconsistency, contact the
Techline.
SupplyPR011:Battery voltage12 V < X < 15 VIn the event of an
inconsistency, consult the
interpretation of fault DF039
Battery voltage.
Computer
activationET065:Activation requestACTIVE INACTIVE
In the event of an
inconsistency, consult the
interpretation of fault DF064
Activation signal.
ET057:Activation signalACTIVE INACTIVE
Page 56 of 91
86A-56V2 MR-413-X44-86A100$150.mif
86A
R01-08
Vdiag No.: A4
Tool Parameter Diagnostic tool title
PR005Radio field intensity
PR011Battery voltage
RADIO
Fault finding – Parameter summary table
Page 60 of 91
86A-60
AFTER REPAIRWhen communication is established, deal with any faults indicated.
V2 MR-413-X44-86A100$190.mif
86A
R01-08
Vdiag No.: A4
ALP 1 No dialogue with the computer
NOTESTry to establish dialogue with a computer on another vehicle to check that the
diagnostic tool is not faulty. If the diagnostic tool is not causing the fault and dialogue
cannot be established with any other computer on the same vehicle, it may be that
a faulty computer is disrupting the fault finding line.
Use a process of successive disconnections to locate this computer.
Check the battery voltage, component code 107, and perform the necessary operations
to obtain the correct voltage (12 V < X < 15 V).
Ensure that the communication conditions are met: + After ignition feed activated and
radio On/Off button pressed.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a Navigation computer, use component 1714, Multimedia
connection unit, for fault finding on the Multimedia interface unit.
Otherwise use component 653, display computer.
Is the multimedia interface unit recognised
during the multiplex network test?The multimedia interface unit activates other
multimedia system computers.
Consult ALP 1 for the multimedia interface unit
(see 86D, Multimedia interface unit,
Fault finding chart).
Reconfigure the multimedia interface unit
(see 86D, Multimedia interface unit,
Configurations and Programming).
NO
YES
A
R108_VA4_ALP1
RADIO
Fault finding – Fault Finding Chart