brake RENAULT TWINGO 2009 2.G Electrical Equipment Workshop Manual

TWINGO - Section 8
Contents
Pages
TWINGO - Section 8 ContentsPages
80A BATTERY
Battery: Precautions for the
repair 80A-1
Battery: Removal - Refitting 80A-2
Battery tray: Removal -
Refitting 80A-6
80B HEADLIGHTS
Front lighting: List and
location of components 80B-1
Halogen bulb: Removal -
Refitting 80B-3
Remote headlight beam
adjustment motor: Removal -
Refitting 80B-5
Halogen headlight: Removal
- Refitting 80B-7
Halogen headlight:
Adjustment 80B-9
Front fog light: Removal -
Refitting 80B-10
Side indicator: Removal -
Refitting 80B-1381A REAR LIGHTING
Rear lighting: List and
location of components 81A-1
Rear wing light: Removal -
Refitting 81A-3
Rear light bulb: Removal -
Refitting 81A-4
3rd brake light: Removal -
Refitting 81A-6
Number plate light: Removal
- Refitting 81A-8
81B INTERIOR LIGHTING
Interior lighting: List and
location of components 81B-1
Interior light: Removal -
Refitting 81B-2
Door switch: Removal -
Refitting 81B-3
Luggage compartment light:
Removal - Refitting 81B-5
81C FUSES
Fuses: List and location of
components 81C-1

80B-9
HEADLIGHTS
Halogen headlight: Adjustment
80B
ADJUSTMENT
I - PREPARATION OPERATION
aPlace the vehicle on a level horizontal working area.
aDo not apply the parking brake.
aCheck and inflate the tyres (see Tyre pressure)
(MR 411, 35A, Wheels and tyres).
aOpen the cover.
aCheck:
-that the luggage compartment is empty,
-that the headlights are clean.
aPosition the headlight beam remote adjustment con-
trol on 0.
aSwitch on the dipped headlights.
II - TEST OPERATION
aPlace a headlight adjustment and checking tool
set to -1% in front of the vehicle (see equipment ins-
tructions).
aCheck the headlight beam adjustment using the
headlight adjustment and checking tool (see the
instructions for the equipment).III - ADJUSTMENT OPERATION
aUsing the headlight adjustment and checking
tool :
-perform lateral adjustment of the headlight using
the screw (1) ,
-adjust the headlight beam by using the screw (2) .
IV - FINAL OPERATION.
aClose the bonnet. Equipment required
headlight adjustment and checking tool
Note:
Do not get into the vehicle throughout the opera-
tion.
119377

81A-1
REAR LIGHTING
Rear lighting: List and location of components
81A
I - LIST OF COMPONENTS
II - LOCATION OF COMPONENTS
1 - Signalling light switch
To remove the signalling light switch (see 84A, Con-
trol - Signals, Signals and lighting switch: Removal
- Refitting, page 84A-8) .2 - UCH
The UCH is located in the dashboard, above the pas-
senger compartment relay/fuse box, for removal (see
87B, Passenger compartment connection unit,
UCH: Removal - Refitting, page 87B-1) .
3 - Passenger compartment fuse and relay box No. Description
(1) Signalling light switch
(2) UCH
(3) Passenger compartment fuse and relay
box
(4) Rear light on wing
(5) High level brake light
(6) License plate light
121133
119507
119504

81A-2
REAR LIGHTING
Rear lighting: List and location of components
81A
4 - Rear light on wing
5 - High level brake light6 - License plate light
119520
119532
121082

81A-4
REAR LIGHTING
Rear light bulb: Removal - Refitting
81A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
1 - Rear light bulbs on the wing
aRemove the rear light on the wing (see 81A, Rear li-
ghting, Rear wing light: Removal - Refitting, page
81A-3) .
2 - High level brake light bulb
aRemove the high level brake light (see 81A, Rear li-
ghting, 3rd brake light: Removal - Refitting, page
81A-6) .
3 - License plate light bulb
aRemove the license plate light (see 81A, Rear li-
ghting, Number plate light: Removal - Refitting,
page 81A-8) .
II - REMOVAL OPERATION FOR PART
CONCERNED
1 - Rear light bulbs on the wing
aUnclip the plate by pressing on the clips (1) .aRemove:
-the side light and brake light bulb (2) ,
-the indicator bulb (3) ,
-the rear fog light bulb (left rear light) or the rever-
sing light bulb (right rear light) (4) .
2 - High level brake light bulb
aRemove the high level brake light bulb (5) .
119535
119536
119534

81A-5
REAR LIGHTING
Rear light bulb: Removal - Refitting
81A
3 - License plate light bulb
aUnclip the light at (6) .
aRemove the license plate light bulb.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
a
1 - Rear light bulbs on the wing
aRefit:
-the side light and brake light bulb (P21/5W),
-the indicator bulb (PY21W),
-the rear fog light bulb (left rear light) or the rever-
sing light bulb (right rear light) (P21W).
2 - High level brake light bulb
aRefit the high level brake light bulb (W16W).
3 - License plate light bulb
aRefit the license plate light bulb (W5W).II - FINAL OPERATION.
1 - Rear light bulbs on the wing
aRefit the rear light on the wing (see 81A, Rear li-
ghting, Rear wing light: Removal - Refitting, page
81A-3) .
2 - High level brake light bulb
aRefit the high level brake light (see 81A, Rear li-
ghting, 3rd brake light: Removal - Refitting, page
81A-6) .
3 - License plate light bulb
aRefit the license plate light (see 81A, Rear lighting,
Number plate light: Removal - Refitting, page
81A-8) .
121080
Note:
When replacing a bulb, only use approved bulbs.

81A-6
REAR LIGHTING
3rd brake light: Removal - Refitting
81A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the blanking covers (1) .
aUnclip the high level brake light with a flat-blade
screwdriver by pressing on the clips (2) .
119530
119531
119534

81A-7
REAR LIGHTING
3rd brake light: Removal - Refitting
81A
aDisconnect:
-the connector (3) from the high level brake light,
-the supply pipe (4) from the rear screen washer jet.
aRemove the high level brake light (5) .
aRemove:
-the rear screen washer jet (6) (see 85A, Wiping -
Washing, Rear screen washer jet: Removal -
Refitting, page 85A-25) ,
-the high level brake light bulb (see 81A, Rear li-
ghting, Rear light bulb: Removal - Refitting,
page 81A-4) .
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit:
-the high level brake light bulb (see 81A, Rear li-
ghting, Rear light bulb: Removal - Refitting,
page 81A-4) ,
-the rear screen washer jet (see 85A, Wiping -
Washing, Rear screen washer jet: Removal -
Refitting, page 85A-25) .
aConnect:
-the rear screen washer jet supply pipe,
-the high level brake light connector.
aRefit:
-the high level brake light,
-the blanking covers.
119532
119534

85A-25
WIPING - WASHING
Rear screen washer jet: Removal - Refitting
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the high level brake light (see 81A, Rear li-
ghting, 3rd brake light: Removal - Refitting, page
81A-6) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the rear screen washer jet by pressing on the
clips (1) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aClip the rear screen washer jet on the high level bra-
ke light.
II - FINAL OPERATION.
aRefit the high level brake light (see 81A, Rear li-
ghting, 3rd brake light: Removal - Refitting, page
81A-6) .
119534

88A-2
WIRING HARNESS
Wiring: Precautions for the repair
88A
I - SAFETY
1 - Potentially dangerous components
Do not leave any unused +12V connectors exposed to
the air without any protection (see Connector: Sea-
ling and locking) (Technical Note 6015A, 88A, Wi-
ring).
Check that there is no contact between the wiring and
the fuel and brake pipes.
Avoid mounting the wiring in areas with a temperature
above 100˚C.
2 - Advice to be followed before any operation
Before carrying out any work on the wiring, disconnect
the battery.
3 - Instructions to be followed during the operation
To prevent the wiring from being damaged, check that
the surrounding area is not mechanically harmful (e.g.:
door windows, sharp corners, burrs, studs, etc.).
The wiring should be at least 30 mm away from any
moving components (belt, pulley, steering column,
etc.).
Depending on the surrounding area, check that the
unused connectors respect the necessary sealing
constraints (see Connector: Sealing and locking)
(Technical Note 6015A, 88A, Wiring).
All of the connections (connectors) used in the engine
compartment are sealed; do not remove the seal from
around the connectors.II - GENERAL RECOMMENDATIONS
Do not connect an earth to a stud with insulating pro-
tection (paint,etc.).
Do not use more than two earth terminals on the same
point.
Do not use power earths on the same point as electro-
nic earths.
To prevent water flowing into the connectors, make a
low point just on the wiring routing (just before the con-
nector).
For connections between fixed and mobile compo-
nents, secure the wiring on the fixed part.
Overlapping of the battery feed wires (positive and ne-
gative) causes disruption; they must be secured sepa-
rately.
Wiring mountings:
- use plastic clips, ensuring that the colour coding is
respected,
-do not use steel clips that are not protected with rub-
ber,
- keep the clips integrated into the wiring during a re-
placement operation,
- do not leave steering wheel wires without protection.
Check that:
- the shunts are correctly secured,
- the connectors are correctly housed and locked.
Wiring routing:
- when it is visible it must be aesthetically pleasing, and
resemble the routing marked during removal,
- prohibit wiring routing in grooves and overlaps (risk of
wear through friction),
- prohibit mounting several wires on the same clip,
- do not lock the connectors or wiring in areas that are
sensitive to drilling (number plate etc.). WARNING
To prevent damaging the connectors, consult the
disconnection procedure (see Connector: Discon-
nection and reconnection) (Technical Note
6015A, 88A, Wiring).
WARNING
To prevent any risk of noise, premature wear, short
circuits, etc. after the refitting operation, mark the
wiring routing and how to connect the connectors.
WARNING
To prevent any damage during the removal opera-
tion, check that the wiring is free from its mountings
(retaining clip, plastic clip, adhesive tape, connec-
tor, etc.).