lock RENAULT TWINGO 2009 2.G Electrical Equipment Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 241
Page 4 of 241
Contents
82A ENGINE IMMOBILISER
Immobiliser system: List and
location of components 82A-1
Ignition switch: Removal -
Refitting 82A-3
Transponder ring: Removal -
Refitting 82A-6
Battery for remote door
locking control: Removal -
Refitting 82A-8
82B HORN
Audible warning: Removal -
Refitting 82B-1
83A INSTRUMENT PANEL
Instr ument panel: Removal -
Refitting 83A-1
Rev counter: Removal -
Refitting 83A-3
83D CRUISE CONTROL
Cruise control - speed
limiter: List and location of
components 83D-1
Switch: Removal - Refitting 83D-2
Steering wheel switch:
Removal - Refitting 83D-384A CONTROL - SIGNALS
Steering column switch
assembly: List and location
of components 84A-1
Steering column switch
assembly: Removal -
Refitting 84A-2
Screen wiper switch:
Removal - Refitting 84A-6
Signals and lighting switch:
Removal - Refitting 84A-8
Hazard warning lights and
central door control:
Removal - Refitting 84A-10
Lighting dimmer: Removal -
Refitting 84A-12
Exter ior rear view mirror
control switch: Removal -
Refitting 84A-13
Heated rear screen: Repair 84A-14
85A WIPING - WASHING
Wiping and washing: List and
location of components 85A-1
Windscreen wiper blade:
Removal - Refitting 85A-5
Windscreen wiper arm:
Removal - Refitting 85A-6
Windscreen wiper
mechanism: Removal -
Refitting 85A-10
Windscreen wiper motor:
Removal - Refitting 85A-12
Rear screen wiper blade:
Removal - Refitting 85A-16
Rear screen wiper arm:
Removal - Refitting 85A-17
Rear screen wiper motor :
Removal - Refitting 85A-19
Rain and light sensor:
Removal - Refitting 85A-20
Page 15 of 241
80B-3
HEADLIGHTS
Halogen bulb: Removal - Refitting
80B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
II - REMOVAL OPERATION FOR PART
CONCERNED
1 - Indicator bulb
aDisconnect the indicator connector.
aTurn the indicator bulb mounting a quarter of a turn
anti-clockwise (1) .
aRemove:
-the indicator "bulb mounting - bulb" assembly,
-the bulb from its mounting.2 - Side light bulbs
aRemove the cover (2) .
aDisconnect the side light connector.
aRemove:
-the "bulb mounting - bulb" assembly (3) from the
side light,
-the bulb from its mounting.
119377
119377
121386
Page 16 of 241
80B-4
HEADLIGHTS
Halogen bulb: Removal - Refitting
80B
3 - Dipped beam headlight and main beam
headlight bulb
aRemove the cover (2) .
aDisconnect the dipped beam headlight and main
beam headlight connector.
aUndo the clip (4) at (5) .
aRemove the dipped beam headlight and main beam
headlight bulb (6) .REFITTING
REFITTING OPERATION FOR PART CONCERNED
1 - Indicator bulb
aRefit:
-a PY21W approved bulb on the indicator bulb
mounting,
-the "bulb mounting - bulb" assembly on the
halogen headlight.
aTurn the indicator bulb mounting a quarter of a turn
clockwise.
aConnect the indicator connector.
2 - Side light bulbs
aRefit:
-a W5W approved bulb on the side light bulb moun-
ting,
-the "bulb mounting - bulb" assembly on the
halogen headlight.
aConnect the side light connector.
aRefit the cover.
3 - Dipped beam headlight and main beam
headlight bulb
aRefit an H4 approved bulb on the halogen headlight.
aFit the clip onto the halogen headlight.
aConnect the dipped beam headlight and the main
beam headlight connector.
aRefit the cover.
119377
119378
Page 23 of 241
80B-11
HEADLIGHTS
Front fog light: Removal - Refitting
80B
II - OPERATION FOR REMOVAL OF PART
CONCERNED
1 - Removing the fog light bulb
a
aDisconnect the fog light connector.
aTurn the fog light bulb (3) a quarter of a turn anti-
clockwise by reaching through
b (2) .
aaTurn the fog light bulb (4) a quarter of a turn anti-
clockwise.
aRemove the fog light bulb.
2 - Removal of the fog light
aRemove:
-the bolts (5) from the front fog light,
-the front fog light. K4M, and 854 – D4F or D7F or K9K
Note:
For D4F/780 engines, the right-hand fog light
bulb is accessed from under the vehicle.
121079
D4F, and 780
Note:
The front bumper must be removed in order to
remove the left-hand fog light bulb.
121079
121079
Page 24 of 241
80B-12
HEADLIGHTS
Front fog light: Removal - Refitting
80B
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
1 - Refitting the fog light bulb
aReplace the fog light bulb with an approved bulb.
aRefit the fog light bulb.
aTurn the fog light bulb a quarter of a turn clockwise.
aConnect the fog light connector.
2 - Refitting the fog light
aRefit the front fog light.
II - FINAL OPERATION.
Refitting the left-hand fog light bulb
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
Refitting the fog light bulb
aRefit:
-the lower bolts of the front wheel arch liner,
-the bolt for the front section of the engine undertray
on the side concerned.
Refitting the fog light
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
D4F, and 780
K4M, and 854
Page 25 of 241
80B-13
HEADLIGHTS
Side indicator: Removal - Refitting
80B
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the side indicator (1) using a small flat-blade
screwdriver (2) .
aRemove the side indicator (1) from the bulb moun-
ting (3) by turning it a quarter of a turn anti-clockwi-
se.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aIf the side indicator bulb is replaced, use a W5W ap-
proved bulb.
aRefit the side indicator on the bulb mounting by tur-
ning it a quarter of a turn clockwise.
aFit the side indicator onto the front wing.
119384
121206
Page 43 of 241
82A-3
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSet the wheels straight ahead.
aLock the airbag computer using the Diagnostic tool
(see MR 413 Fault finding, 88C, Airbags and pre-
tensioners, Fault finding - Replacement of com-
ponents).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the rev counter (see 83A, Instrument pa-
nel, Rev counter: Removal - Refitting, page 83A-
3) .
aRemove:
-the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-6)
-the steering wheel ( (see Steering wheel: Remo-
val - Refitting) ),
-the steering column switch assembly (see 84A,
Control - Signals, Steering column switch as-
sembly: Removal - Refitting, page 84A-2) ,
-the antenna/transponder ring (see 82A, Engine
immobiliser, Transponder ring: Removal - Re-
fitting, page 82A-6) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aMake a saw mark on the shear bolt.
aRemove the bolt (1) .
aLoosen the connector at (2) .
aDisconnect the starter switch connector. Equipment required
Diagnostic tool
ENGINE REV COUNTER
119489
119490
Page 44 of 241
82A-4
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
aPosition the ignition key between the first and se-
cond position (+ accessories and + after ignition
feed) (3) .
aPress the retaining lug (4) .
aRemove the ignition switch.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace:
-the ignition switch bolt,
-the steering wheel bolt.
II - REFITTING OPERATION FOR PART
CONCERNED
aaPosition the ignition key between the first and se-
cond position (+Accessories and +APC) (5) .
aPress the retaining lug (6) .
aFit the ignition switch.
aTighten the shear bolt (7) until the bolt head shears
off.
aConnect the starter switch connector.
aLock the starter switch connector.
108441
Note:
To protect against tampering, always secure the
ignition switch with a shear bolt.
Be sure to recover the sheared-off part of the
bolt after it has been tightened.
108441
119491
Page 45 of 241
82A-5
ENGINE IMMOBILISER
Ignition switch: Removal - Refitting
82A
III - FINAL OPERATION.
aRefit:
-the antenna/transponder ring (see 82A, Engine
immobiliser, Transponder ring: Removal - Re-
fitting, page 82A-6) ,
-the steering column switch assembly (see 84A,
Control - Signals, Steering column switch as-
sembly: Removal - Refitting, page 84A-2) ,
-the steering wheel ( (see Steering wheel: Remo-
val - Refitting) ),
-the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-6) .
aRefit the rev counter (see 83A, Instrument panel,
Rev counter: Removal - Refitting, page 83A-3) .
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aUnlock the airbag computer using the Diagnostic
tool (see MR 413 Fault finding, 88C, Airbags and
pretensioners, Fault finding - Replacement of
components). ENGINE REV COUNTER
Page 48 of 241
82A-8
ENGINE IMMOBILISER
Battery for remote door locking control: Removal - Refitting82A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolt (1) .
aOpen the key with a small flat-blade screwdriver at
(2) .aRemove the battery (3) from the door locking remote
control using a small flat-blade screwdriver.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
a
aFit the door locking remote control battery.
aClose the key.
aTighten the bolt.
107732
107733
107731
WARNING
To ensure that the remote control operates cor-
rectly, take care not to damage the battery con-
tacts.
Only handle the new battery with dry, grease-free
hands or wearing clean gloves to avoid any risk
of dir t and oxidation on the battery.