wheel RENAULT TWINGO 2009 2.G Engine And Peripherals User Guide

10A-14
ENGINE AND CYLINDER BLOCK ASSEMBLY
Lower cover: Removal - Refitting
D4F or D7F
10A
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion).
aSet the wheels straight ahead.
aPosition the flywheel immobiliser.
aRemove the cover from the universal joint (do not
keep).
aRemove the universal joint bolt (do not keep).
aRemove the universal joint from the steering box.
aLoosen the tie rod lower bolts.
aRemove the tie rod upper bolts.aRemove:
-the nuts (1) from the track rod ends,
-the track rod ends using the (Tav. 476),
-the bolts (2) from the lower ball joints,
-the lower arm ball joints.
aRemove the lower engine tie-bar (3) (see 19D, En-
gine mounting, Lower engine tie-bar: Removal -
Refitting, page 19D-18) .
aRemove:
-the subframe rear tie rod inner bolts (4) ,
-the subframe rear tie rod outer bolts (5) .
119544
119222
119335

10A-16
ENGINE AND CYLINDER BLOCK ASSEMBLY
Lower cover: Removal - Refitting
D4F or D7F
10A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the sump fitted with a new seal,
-the sump bolts.
aTighten to torque and in order the sump bolts (10
N.m).
III - FINAL OPERATION
aRefit the engine flywheel guard.aRefit the subframe, gradually tightening the nuts of
the (Tav. 1233-01).
aRemove the threaded rods of the (Tav. 1233-01)
one by one, replacing them with the subframe
mounting bolts.
aTorque tighten:
-the front subframe bolts (62 N.m),
-the rear subframe bolts (105 N.m),
-the front end cross member bolts (21 N.m)
-the subframe rear tie rod inner bolts (21 N.m),
-the subframe rear tie rod outer bolts (90 N.m).
aRefit:
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the lower arm ball joints,
-the lower ball joint bolts,
-track rod ends,
-the track rod end nuts,
aTorque tighten:
-the lower ball joint bolts (62 N.m),
-the track rod end nuts (37 N.m).
aRefit the subframe tie rod upper bolts.
aTorque tighten the subframe tie rod upper bolts
(21 N.m).
aTorque tighten the subframe tie rod lower bolts
(62 N.m).
aFit the steering box universal joint.
aRefit the universal joint bolt.
aTorque tighten the universal joint (24 N.m).
aRemove the flywheel immobiliser.
aRefit:
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
18643
D4F, and 772 – D7F
D4F, and 780 or 782

10A-18
ENGINE AND CYLINDER BLOCK ASSEMBLY
Lower cover: Removal - Refitting
K4M
10A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the dipstick,
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the engine undertray.
aDrain the engine oil (see 10A, Engine and cylinder
block assembly, Engine oil: Draining - Refilling,
page 10A-22) .
aRemove:
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),-the rear engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents).
aRemove:
-the front right-hand driveshaft flange bolt (1) on the
relay bearing,
-the bolts (2) from the front right-hand driveshaft re-
lay bearing,
-the front right-hand driveshaft relay bearing. Tightening torquesm
sump bolts (initial
torque)14 N.m
sump bolts14 N.m
sump bolts on the gear-
box44 N.m
bolt mounting the multi-
function support on the
sump25 N.m
catalytic pre-converter
upstream bracket bolt44 N.m
driveshaft relay bearing
bolts44 N.m.
right-hand driveshaft
bracket bolt on the relay
bearing21 N.m
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
128800

10A-21
ENGINE AND CYLINDER BLOCK ASSEMBLY
Lower cover: Removal - Refitting
K4M
10A
aPretighten in order (1) , (2) , (19) , (20) , (17) , (18)
the sump bolts (initial torque) (14 N.m).
aTighten to torque and in order the sump bolts (14
N.m).
aTorque tighten:
-the sump bolts on the gearbox (44 N.m),
-the bolt mounting the multifunction support on
the sump (25 N.m).
III - FINAL OPERATION
aTorque tighten the catalytic pre-converter up-
stream bracket bolt (44 N.m).
aRefit the driveshaft relay bearing.
aTorque tighten:
-the driveshaft relay bearing bolts (44 N.m.),
-the right-hand driveshaft bracket bolt on the re-
lay bearing (21 N.m).
aRefit:
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents),
-the rear engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the dipstick,
-the engine undertray.
aTop up the engine oil (see 10A, Engine and cylin-
der block assembly, Engine oil: Draining - Refill-
ing, page 10A-22) .
20171

10A-33
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil-coolant heat exchanger: Removal - Refitting
K9K
10A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove:
-the engine cover,
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection).
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aRemove the expansion bottle bolt.
aRemove the expansion bottle.
aUnclip the cooling hose on the lower section of the
engine cooling fan.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect:
-the cooling hose (1) using the (Mot. 1448),
-the oil pressure sensor connector (2) .
aRemove:
-the bolt (3) from the oil filter support,
-the oil filter holder.
aRemove:
-the oil cooler nipple,
-the oil-water heat exchanger. Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
121432
Note:
Be prepared for engine oil and coolant to flow
out.

10A-34
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil-coolant heat exchanger: Removal - Refitting
K9K
10A
REFITTING
I - REFITTING PREPARATION OPERATION
aUsing the buffing pads, clean the pressure faces of
the oil-water heat exchanger and the cylinder block.
aFit new seals on the oil-water heat exchanger with
soapy water.
aCheck the condition of the oil-water heat exchanger
nipple seals.
II - REFITTING OPERATION FOR PART
CONCERNED
aCoat the nipple with high resistance thread lock.
aRefit:
-the coolant-oil heat exchanger,
-the oil-coolant heat exchanger nipple.
aFit a new seal on the oil filter holder.
aRefit:
-the oil filter holder,
-the oil filter mounting bolt.
aTighten the oil filter mounting bolt.
aConnect:
-the oil pressure sensor connector,
-the cooling hose using the (Mot. 1448).
III - FINAL OPERATION
aClip the cooling hose on to the lower section of the
engine cooling fan.
aPosition the expansion bottle.
aRefit the expansion bottle bolt.aFill the cooling system (see 19A, Cooling, Cooling
system: Draining - Refilling, page 19A-9) .
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the engine cover. WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).
WARNING
The gaskets must always be replaced with new
gaskets.
Note:
The oil-water heat exchanger nipple seals cannot
be separated; the entire assembly must be
replaced.

10A-35
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil-coolant heat exchanger: Removal - Refitting
D4F, and 780 or 782
10A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the oil filter (see 10A, Engine and cylinder block
assembly, Oil filter: Removal - Refitting, page
10A-29) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aFit the tool (Ms. 583) onto the oil-coolant heat ex-
changer hoses (1) .
aRelease the clips (2) using the (Mot. 1448).
aConnect the oil-coolant heat exchanger hoses.
aRemove:
-the nipple (3) from the oil-coolant heat exchanger,
-the oil-water heat exchanger. Special tooling required
Ms. 583Pipe clamps .
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
oil-coolant heat
exchanger nipple30 N.m
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.121726
121402

10A-36
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil-coolant heat exchanger: Removal - Refitting
D4F, and 780 or 782
10A
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: coolant-engine oil
heat exchanger seal on the cylinder block.
aUse a GREY ABRASIVE PAD (see Vehicle: Parts
and consumables for the repair) (04B, Consum-
ables - Products) to clean the bearing faces of the
oil-coolant heat exchanger and the cylinder block.
II - REFITTING OPERATION FOR PART
CONCERNED
aCoat the nipple with HIGH STRENGTH THREAD-
LOCK (see Vehicle: Parts and consumables for
the repair) (04B, Consumables - Products).
aRefit:
-the oil-coolant heat exchanger,
-the oil-coolant heat exchanger nipple.
aTorque tighten the oil-coolant heat exchanger nip-
ple (30 N.m).
aConnect the oil-coolant heat exchanger hoses.
aRefit the clips using the (Mot. 1448).
aRemove the tools (Ms. 583).
III - FINAL OPERATION
aRefit:
-the oil filter (see 10A, Engine and cylinder block
assembly, Oil filter: Removal - Refitting, page
10A-29) ,
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) . WARNING
To ensure proper sealing, the gasket surfaces
must be clean, dry and not greasy (avoid any fin-
ger marks).

10A-37
ENGINE AND CYLINDER BLOCK ASSEMBLY
Conrod bearing shell: Removal - Refitting
K9K
10A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the engine undertray.
aDrain the oil from the engine (see 10A, Engine and
cylinder block assembly, Engine oil: Draining -
Refilling, page 10A-22) .
aRemove the oil filter (see 10A, Engine and cylinder
block assembly, Oil filter: Removal - Refitting,
page 10A-29) .
aRemove the lower engine tie-bar (see 19D, Engine
mounting, Lower engine tie-bar: Removal - Refit-
ting, page 19D-18) .
aStrap the radiator to the vehicle using safety
strap(s).
aRemove the front axle subframe (see Front axle
subframe: Removal - Refitting) (31A, Front axle
components).
aRemove the relay bearing of the front right-hand
wheel driveshaft. Special tooling required
Mot. 1914Tool for fitting G9 con rod
bear ing shells
Mot. 1920Tool for fitting F9 / K9 con rod
bear ing shells
Equipment required
safety strap(s)
component jack
indelible pencil
torque wrench
Diagnostic tool
Tightening torquesm
con rod cap bolts20 N.m + 45˚ ±± ± ±
6˚
oil pump bolts25 N.m
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair (see Vehicle: Precautions for the repair) .
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
123838

10A-44
ENGINE AND CYLINDER BLOCK ASSEMBLY
Conrod bearing shell: Removal - Refitting
K9K
10A
aTilt the engine oil sump forwards in order to access
the oil pump bolts.
aTorque tighten the oil pump bolts (25 N.m) using
the torque wrench PROSTEEL, part number 77 11
226 888 starting with the 13 mm bolt.
a
aRefit the engine oil sump bolts.
aTorque tighten in order the engine oil sump bolts
(see 10A, Engine and cylinder block assembly,
Lower cover: Removal - Refitting, page 10A-6) .
aRefit the catalytic converter upstream stay (see 19B,
Exhaust, Catalytic converter: Removal - Refit-
ting, page 19B-12) .
aConnect the connector to the oil level sensor.
aRefit the relay bearing of the front right-hand wheel
driveshaft (see Front right-hand driveshaft: Re-
moval - Refitting) .
aRefit the front axle subframe (see Front axle sub-
frame: Removal - Refitting) (31A, Front axle com-
ponents).
aRemove the safety strap(s) from the radiator.
aRefit the lower engine tie-bar (see 19D, Engine
mounting, Lower engine tie-bar: Removal - Refit-
ting, page 19D-18) .aDisconnect the crankshaft position sensor (4) to pre-
vent the engine from starting.
aRefit the oil filter (see 10A, Engine and cylinder
block assembly, Oil filter: Removal - Refitting,
page 10A-29)
aFill up the engine oil (see 10A, Engine and cylinder
block assembly, Engine oil: Draining - Refilling,
page 10A-22) .
aStart the engine using the starter until the engine oil
warning light goes out.
aConnect the crankshaft position sensor.
aRefit the engine undertray.
aClear the present faults using the Diagnostic tool.
140918
Note:
Check that the engine oil sump seal is definitely
in place before tightening the engine oil sump
bolts.
123824