torque RENAULT TWINGO 2009 2.G Engine And Peripherals Workshop Manual

19A-63
COOLING
Coolant pump inlet pipe: Removal - Refitting
K4M
19A
II - REMOVAL OPERATION
aRemove the clip (4) from each cooling hose using
the tool (Mot. 1448).
aDisconnect the cooling hoses from the coolant pump
inlet pipe.
aRemove:
-the bolts (5) from the coolant pump inlet pipe,
-the coolant pump inlet pipe.
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: seal between cool-
ant pump inlet pipe and coolant pump.
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease:
-the seal housing in the cylinder block,
-the coolant pump inlet pipe seal housing if it is be-
ing reused.
II - REFITTING OPERATION
aRefit the coolant pump inlet pipe fitted with a new
seal.aTorque tighten in order the coolant pump inlet pipe
bolts (25 N.m).
aConnect the cooling hoses to the coolant pump inlet
pipe.
aFit each cooling hose clip using the tool (Mot. 1448).
III - FINAL OPERATION
aConnect:
-the oil pressure sensor connector,
-the pinking sensor connector.
aRefit:
-dipstick guide ,
-the dipstick.
aConnect the battery (see ) (80A, Battery).
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .
aRefit the engine undertray.
131781
131781

19A-68
COOLING
Coolant temperature sensor: Removal - Refitting
D4F, and 780
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).Tightening torquesm
coolant temperature
sensor23 Nm

19A-70
COOLING
Coolant temperature sensor: Removal - Refitting
D4F, and 780
19A
-the coolant temperature sensor.
aTorque tighten the coolant temperature sensor
(23 Nm).
aConnect the coolant temperature sensor connector.
III - FINAL OPERATION
aRefit the throttle valve (see 12A, Fuel mixture,
Throttle valve: Removal - Refitting, page 12A-20)
.
aPush the turbocharger air outlet pipe clip in the di-
rection of the arrow (7) .
aConnect the turbocharger air outlet pipe onto the tur-
bocharger.
aRefit the turbocharger air outlet pipe bolt on the
throttle valve.
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .
122666

19B-10
EXHAUST
Exhaust: Precautions for the repair
19B
Exhaust trunking with 1 bolt
Exhaust trunking with 2 bolts
Fit the exhaust trunking onto the part of the exhaust
system fitted to the vehicle.
Position the pipe onto the lugs (2) inside the exhaust
trunking.
Tighten the exhaust trunking bolt(s) slightly (depending
on the version).
Position the second part of the exhaust system under
the vehicle, fitting it in the exhaust trunking.Position the second exhaust pipe onto the lugs inside
the exhaust trunking.
Check that the two cut marks (3) are aligned (if applica-
ble).
Position the trunking so that there is no risk of contact
between its bolt or bolts and the heat shields.
Torque tighten
-the exhaust trunking nut with 1 bolt (25 N.m) (if fit-
ted),
-the exhaust trunking nuts with 2 bolts (18 N.m) (if
fitted).
Check the following and deal with if necessary:
-no underbody contact between the exhaust system
and the heat shields,
-all of the heat shields are present and secure.
Start the engine.
Check that there are no leaks: deal with any leaks.
95478
119681
Note:
If necessary, use a workshop jack to lift and hold
the heavy and bulky components of the exhaust
system.
99227
Note:
Any damaged heat shields must be replaced.

19B-12
EXHAUST
Catalytic converter: Removal - Refitting
K9K
19B
PARTS AND CONSUMABLES FOR THE REPAIR
Pièces à remplacer systématiquement :
-air inlet pipe seals,
-the catalytic converter seal on the turbocharger,
-any stud and/or nut on the turbocharger or damaged
catalytic converter,
-The exhaust system sealing ring on the catalytic con-
verter.
Ingrédients :
-ABRASIVE PADS,
-SURFACE CLEANER.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove:
-the windscreen wiper arms ( (see Windscreen
wiper arm: Removal - Refitting) ),
-the scuttle panel grille ( (see Scuttle panel grille:
Removal - Refitting) ),
-the scoop under the scuttle panel grille ( (see
Scoop under the scuttle panel grille: Removal -
Refitting) ),
-the air filter box (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the catalytic converter bolts (1) on the tur-
bocharger.
aRaise the vehicle.
aRemove the engine tie-bar (see 19D, Engine
mounting, Lower engine tie-bar: Removal - Refit-
ting, page 19D-18) . Tightening torquesm
catalytic converter studs
on the turbocharger9 Nm
catalytic converter nuts
on the turbocharger26 Nm
catalytic converter
upstream strut bolts on
the engine44 Nm
catalytic converter
downstream strut bolts
on the gearbox21 Nm
catalytic converter
downstream strut nut on
the gearbox21 Nm
catalytic converter
upstream strut bolts on
the catalytic converter26 Nm
catalytic converter
downstream strut bolt
on the catalytic con-
verter21 Nm
exhaust pipe bolts on
the catalytic converter21 Nm
IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see 19B, Exhaust, Exhaust: Precautions
for the repair, page 19B-8) .
112328

19B-14
EXHAUST
Catalytic converter: Removal - Refitting
K9K
19B
aIf they are replaced, torque tighten the catalytic
converter studs on the turbocharger (9 Nm ).
II - REFITTING OPERATION FOR PART
CONCERNED
aFrom underneath the vehicle, fit:
-the catalytic converter on the turbocharger fitted
with a new seal between the catalytic converter
and the turbocharger,
-one of the catalytic converter nuts on the turbo-
charger.
aIn order, fit (without tightening):
-the catalytic converter upstream strut bolts on the
engine,
-the catalytic converter downstream strut bolt and
nut on the gearbox,
-the catalytic converter upstream strut bolts on the
catalytic converter,
-the catalytic converter downstream strut bolt on the
catalytic converter,
-the catalytic converter nuts on the turbocharger,
aTorque tighten and in order:
-the catalytic converter nuts on the turbocharger
(26 Nm),
-the catalytic converter upstream strut bolts on
the engine (44 Nm),
-the catalytic converter downstream strut bolts
on the gearbox (21 Nm),
-the catalytic converter downstream strut nut on
the gearbox (21 Nm),
-the catalytic converter upstream strut bolts on
the catalytic converter (26 Nm),
-the catalytic converter downstream strut bolt
on the catalytic converter (21 Nm).
aFit in order:
-a new exhaust system sealing ring on the catalytic
converter,
-the exhaust pipe on the catalytic converter,
-the exhaust pipe springs and bolts on the catalytic
converter.aTorque tighten the exhaust pipe bolts on the cata-
lytic converter (21 Nm).
aCheck the following and deal with if necessary:
-that there is no contact with the underbody,
-the presence and correct positioning of all the ex-
haust pipe heat shields.
III - FINAL OPERATION.
aRefit:
-the engine tie-bar (see 19D, Engine mounting,
Lower engine tie-bar: Removal - Refitting, page
19D-18) ,
-the air filter box (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the scoop under the scuttle panel grille ( (see
Scoop under the scuttle panel grille: Removal -
Refitting) ),
-the scuttle panel grille ( (see Scuttle panel grille:
Removal - Refitting) ),
-the windscreen wiper arms ( (see Windscreen
wiper arm: Removal - Refitting) ).
aConnect the battery ( (see Battery: Removal - Re-
fitting) ).
aStart the engine.
aCheck that there are no leaks and deal with them if
necessary. Note:
Check that there is no contact between the cata-
lytic conver ter and the turbocharger oil return
pipe during the entire catalytic converter tighten-
ing operation.

19B-16
EXHAUST
Catalytic converter: Removal - Refitting
D4F, and 780 or 782
19B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the air filter box strut bolt,-the air filter box strut,
-the upstream oxygen sensor (see 17B, Petrol in-
jection, Oxygen sensors: Removal - Refitting,
page 17B-13) . Tightening torquesm
catalytic converter lower
bracket bolt on the gear-
box44 N.m
bolts of the catalytic
converter lower bracket
on the engine25 N.m
side bracket bolts on the
catalytic converter21 N.m
side bracket bolts on the
engine21 N.m
catalytic converter nuts
on the turbocharger (ini-
tial torque)20 N.m
catalytic converter nuts
on the turbocharger30 N.m
bolts of the catalytic
converter lower bracket
on the catalytic con-
verter (initial torque)20 N.m
bolts of the catalytic
converter lower bracket
on the catalytic con-
verter30 N.m
exhaust downpipe bolts21 N.m
catalytic converter strut
nut21 N.m
catalytic converter strut
bolt on the rocker cover21 N.m

19B-20
EXHAUST
Catalytic converter: Removal - Refitting
D4F, and 780 or 782
19B
-the new nuts with the catalytic converter spacers
on the turbocharger.
aAttach the downstream oxygen sensor wiring har-
ness to the catalytic converter.
aClip on the catalytic converter downstream oxygen
sensor connector.
aConnect the catalytic converter downstream oxygen
sensor connector.
III - FINAL OPERATION
aRefit:
-the catalytic converter lower exhaust bracket,
-the bracket bolt on the gearbox,
-the bracket bolts on the engine,
-the catalytic converter side exhaust bracket,
-the catalytic converter side bracket bolts,
-the engine side bracket bolts.
aTorque tighten:
-the catalytic converter lower bracket bolt on the
gearbox (44 N.m),
-the bolts of the catalytic converter lower brack-
et on the engine (25 N.m),
-the side bracket bolts on the catalytic converter
(21 N.m),
-the side bracket bolts on the engine (21 N.m),
-the catalytic converter nuts on the turbocharger
(initial torque) (20 N.m),
-the catalytic converter nuts on the turbocharger
(30 N.m),
-the bolts of the catalytic converter lower brack-
et on the catalytic converter (initial torque) (20
N.m),
-the bolts of the catalytic converter lower brack-
et on the catalytic converter (30 N.m).
aRefit:
-the exhaust downpipe,
-the intermediate pipe clip.
aTighten the intermediate pipe clip.
aRefit the exhaust downpipe bolts on the catalytic
converter.
aTorque tighten the exhaust downpipe bolts (21
N.m).aRefit:
-the rear suspended engine mounting (see 19D,
Engine mounting, Lower engine tie-bar: Re-
moval - Refitting, page 19D-18) ,
-the turbocharger strut.
-the catalytic converter strut bolt on the rocker cov-
er,
-the catalytic converter strut nut.
aTorque tighten:
-the catalytic converter strut nut (21 N.m),
-the catalytic converter strut bolt on the rocker
cover (21 N.m).
aPosition the turbocharger air outlet pipe.
aPush the turbocharger air outlet pipe clip (15) in the
direction of the arrow.
aConnect the turbocharger air outlet pipe onto the tur-
bocharger.
aRefit:
-the turbocharger air outlet rigid pipe bolt on the
throttle valve,
-the upstream oxygen sensor (see 17B, Petrol in-
jection, Oxygen sensors: Removal - Refitting,
page 17B-13) ,
-the air filter box strut,
-the air filter box strut bolt,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) .
122666

19B-23
EXHAUST
Expansion chamber: Removal - Refitting
D4F, and 780 or 782
19B
REMOVING THE FRONT SECTION OF THE
EXPANSION CHAMBER
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the clip (1) between the front section of the expan-
sion chamber and the expansion chamber,
-the bolts (2) and the springs from the front section
of the expansion chamber on the catalytic convert-
er,-the front section of the expansion chamber,
-the exhaust downpipe sealing ring from the catalyt-
ic converter and discard it.
REFITTING THE FRONT SECTION OF THE
EXPANSION CHAMBER
aParts always to be replaced:
-any stud and/or nut from the damaged catalytic
converter,
-the exhaust system sealing ring on the catalytic
converter,
-clip.
I - REFITTING PREPARATIONS OPERATION
aUsing RUBBING PADS clean the bearing faces of:
-on the catalytic converter,
-on the exhaust system.
aThen, degrease the bearing faces with SURFACE
CLEANER (see Vehicle: Parts and consumables
for the repair) (MR 411, 04B, Consumables - Prod-
ucts).
II - REFITTING OPERATION FOR PART
CONCERNED
aPlace the front section of the expansion chamber on
the catalytic converter fitted with a new sealing ring.
aRefit:
-the expansion chamber front section bolts and
springs on the catalytic converter,
-a new clip between the front section of the expan-
sion chamber and the expansion chamber,
aTorque tighten the expansion chamber front sec-
tion bolts on the catalytic converter (21 Nm).
REMOVING THE EXPANSION CHAMBER
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the clip between the front section of the ex-
pansion chamber and the expansion chamber.
aRemove the expansion chamber. Tightening torquesm
expansion chamber
front section bolts on
the catalytic converter21 Nm
IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see 19B, Exhaust, Exhaust: Precautions
for the repair, page 19B-8) .
122831

19B-25
EXHAUST
Expansion chamber: Removal - Refitting
K4M
19B
REMOVING THE EXHAUST PIPE FRONT
EXPANSION CHAMBER
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the engine undertray bolts,
-the engine undertray.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the expansion chamber clip (1) .
aRemove:
-the nuts (2) on the catalytic converter bracket,
-the expansion chamber,
-the catalytic converter seal,
-the catalytic converter studs using a roller-type
stud removal tool. Equipment required
roller-type stud removal tool
Tightening torquesm
catalytic converter studs7 N.m
catalytic converter
bracket nuts21 N.m
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair (see 19B, Exhaust, Exhaust: Precautions
for the repair, page 19B-8) .
IMPORTANT
Wear protective gloves during the operation.
IMPORTANT
Wear heat protective gloves during the operation.
WARNING
To prevent the surrounding components from over-
heating, do not damage (tear, pierce bend etc.) a
heat shield.
All damaged heat shields must be replaced.
131772
132340