clock RENAULT TWINGO 2009 2.G Engine And Peripherals Owner's Manual

11A-61
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K4M
11A
3 - Timing belt tension
aPosition the adjustable index (25) opposite the mark
(26) , by turning the eccentric (27) clockwise using a
6 mm Allen key.
aTorque tighten the tensioning roller nut(7 N.m).aRefit:
-the lower timing cover (28) ,
-the crankshaft accessories pulley (29) (see 11A,
Top and front of engine, Crankshaft accesso-
ries pulley: Removal - Refitting, page 11A-20) .
aTighten to torque the lower timing cover bolts ( 12
N.m).
103263
132385

11A-62
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K4M
11A
aPosition the (Mot. 1490-01) (30) on the camshaft
pulleys.
aTorque tighten:
-and angle tighten the exhaust camshaft pulley
nut (30 N.m + 84˚),
-the camshaft dephaser pulley bolt (100 N.m).
aRefit the dephaser pulley bolt cover.
aRemove:
-the timing flap from the lower timing cover,
-the (Mot. 1496),-the TDC setting pin (Mot. 1489),
-the (Mot. 1490-01).
4 - Checking the tension
aRotate the crankshaft twice in a clockwise direction,
on the timing end, before aligning the marks (on the
camshaft dephaser) already made by the operator.
aScrew in the TDC setting pin (Mot. 1489).
aMove the crankshaft slowly and smoothly to rest on
the TDC setting pin.
aRemove the TDC setting pin (Mot. 1489).
103265
109052

11A-63
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K4M
11A
aCheck through the lower timing cover window that
the adjustable index (31) is opposite the notch (32) ,
if this is not the case:
-loosen the timing tensioning roller nut by up to one
turn while holding the eccentric with a 6 mm Allen
key,
-gradually move the adjustable index marker (31)
opposite the mark (32) turning the eccentric cam
(33) clockwise.
aTorque tighten the timing tension wheel nut (27
N.m).5 - Checking the timing
aEnsure that the index and the notch on the timing
tensioning roller are in the correct position before
checking the timing.
aScrew in the TDC setting pin (Mot. 1489).
aBring the crankshaft slowly and smoothly to rest
against the TDC setting pin (Mot. 1489).
aPosition (without forcing) the camshaft setting tool
(Mot. 1496) fitted with the (Mot. 1750) (the camshaft
end grooves must be horizontal and offset towards
the bottom).
aRemove:
-the timing tool (Mot. 1496) fitted with the (Mot.
1750),
-the TDC setting pin (Mot. 1489).
109051
103263
14490
Note:
The timing adjustment and tensioning operation
must be repeated if the camshaft setting tool
does not engage .

11A-142
TOP AND FRONT OF ENGINE
Camshaft seal, timing end: Removal - Refitting
K4M
11A
Removing the seal on the exhaust side and inlet
side
aPosition the claws of the (Mot. 1577) on the cam-
shaft.
aPush the (Mot. 1577) until contact is made between
the ends of the claws and the camshaft seal.aSeparate the claws by turning the nut (3) clockwise
using an open-jawed spanner.
aRemove the camshaft seal by turning the bolt clock-
wise using a spanner (4) .
126608
126608
126609
126605