fuel RENAULT TWINGO 2009 2.G Engine And Peripherals Owner's Manual

10A-106
ENGINE AND CYLINDER BLOCK ASSEMBLY
Valves: Adjustment
D4F or D7F
10A
I - PREPARATION STAGE FOR ADJUSTING THE
VALVE CLEARANCES
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove:
-the front right-hand wheel, (see Front wheel arch
liner: Removal - Refitting)
-the front right-hand wheel arch liner (see MR 412
Bodywork, 55A, Exterior protection, Wheel arch
liner: Removal - Refitting),
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the inlet manifold (see 12A, Fuel mixture, Inlet
distributor: Removal - Refitting, page 12A-29) ,
-the rocker cover (see 11A, Top and front of en-
gine, Rocker cover: Removal - Refitting, page
11A-66) .
II - ADJUSTING THE VALVE CLEARANCES
aAdjust the valve clearances (see Technical Note
6004A, Petrol engine - 4 cylinder - D4, 10A, Tim-
ing-Cylinder head: Refitting).
aAdjust the valve clearances (see MR Components,
MR - Mot - D - (E), 4 cylinder cast-iron engine
(petrol), 10 Engine and peripherals, Engine re-
pair).
III - FINAL OPERATION
aRefit:
-the rocker cover (see 11A, Top and front of en-
gine, Rocker cover: Removal - Refitting, page
11A-66) ,
-the inlet manifold (see 12A, Fuel mixture, Inlet
distributor: Removal - Refitting, page 12A-29) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,-the front right-hand wheel arch liner (see MR 412
Bodywork, 55A, Exterior protection, Wheel arch
liner: Removal - Refitting),
-the front right-hand wheel ( (see Wheel: Removal
- Refitting) ).
aConnect the battery ( (see Battery: Removal - Re-
fitting) ).
D4F
D7F

10A-110
ENGINE AND CYLINDER BLOCK ASSEMBLY
Flywheel: Removal - Refitting
K4M
10A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the engine undertray,
-the battery (see Battery: Removal - Refitting)
(80A, Battery),
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the petrol injection computer (see 17B, Petrol in-
jection, Petrol injection computer: Removal -
Refitting, page 17B-20) ,
-the battery tray (see Battery tray: Removal - Re-
fitting) (80A, Battery),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
aDrain:
-the gearbox (see Manual gearbox oils: Draining -
Filling) (21A, Manual gearbox),
-the engine cooling system (see 19A, Cooling,
Cooling system: Draining - Refilling, page 19A-
9) ,
-the refrigerant circuit using a refrigerant charging
station (see Refrigerant circuit: Draining - Fill-
ing) (62A, Air conditioning).aRemove:
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents),
-the front left-hand wheel driveshaft (see Front left-
hand driveshaft: Removal - Refitting) (29A,
Driveshafts),
-the front right-hand wheel driveshaft (see Front
right-hand driveshaft: Removal - Refitting)
(29A, Driveshafts),
-the differential output seals (see Differential out-
put seal: Removal - Refitting) (21A, Manual gear-
box),
-the « engine - gearbox » assembly (see 10A, En-
gine and cylinder block assembly, Engine -
gearbox assembly: Removal - Refitting, page
10A-74) (21A, Manual gearbox),
-the manual gearbox (see Manual gearbox: Re-
moval - Refitting) ,
-the « pressure plate - disc » assembly (see Pres-
sure plate - Disc: Removal - Refitting) (20A,
Clutch).
II - REMOVAL OPERATION
aRemove:
-the flywheel bolts,
-the (Mot. 1677) (1) , Special tooling required
Mot. 1677Flywheel locking tool.
Equipment required
refrigerant charging station
Tightening torquesm
flywheel bolts70 N.m
109158

10A-111
ENGINE AND CYLINDER BLOCK ASSEMBLY
Flywheel: Removal - Refitting
K4M
10A
-the flywheel.
REFITTING
I - REFITTING PREPARATION OPERATION
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease:
-the flywheel bearing face if reusing,
-the crankshaft bearing face.
aAlways replace the flywheel bolts.
II - REFITTING OPERATION
aFit the flywheel.
aFit the new flywheel bolts without tightening them.
aPosition the (Mot. 1677).
aTighten to torque and in order the flywheel bolts
(70 N.m).
III - FINAL OPERATION
aRefit:
-the « pressure plate - disc » assembly (see Pres-
sure plate - Disc: Removal - Refitting) (20A,
Clutch),
-the manual gearbox (see Manual gearbox: Re-
moval - Refitting) (21A, Manual gearbox).-the « engine and gearbox » assembly (see 10A,
Engine and cylinder block assembly, Engine -
gearbox assembly: Removal - Refitting, page
10A-74) ,
-the differential output seals (see Differential out-
put seal: Removal - Refitting) (21A, Manual gear-
box),
-the front right-hand wheel driveshaft (see Front
right-hand driveshaft: Removal - Refitting)
(29A, Driveshafts),
-the front left-hand wheel driveshaft (see Front left-
hand driveshaft: Removal - Refitting) (29A,
Driveshafts),
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents),
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the battery tray (see Battery tray: Removal - Re-
fitting) (80A, Battery),
-the petrol injection computer (see 17B, Petrol in-
jection, Petrol injection computer: Removal -
Refitting, page 17B-20) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the battery (see Battery: Removal - Refitting)
(80A, Battery).
aPerform the following operations:
-fill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) ,
-fill the gearbox (see Manual gearbox oils: Drain-
ing - Filling) (21A, Manual gearbox).
-fill the refrigerant circuit using a refrigerant charg-
ing station (see Refrigerant circuit: Draining -
Filling) (62A, Air conditioning).
aRefit the engine undertray.
109158

11A-2
TOP AND FRONT OF ENGINE
Pressure at end of compression: Check
D4F
11A
CHECK
I - PREPARATION OPERATION FOR CHECK
aRemove the plugs (see 17A, Ignition, Plugs: Re-
moval - Refitting, page 17A-12) .
aConnect a petrol compression gauge (1) .
aRun command with Diagnostic tool :
-RZ009: VEHICLE FUNCTION PROGRAMMING,
-VP036: FUEL SUPPLY INHIBITION.
aPut the vehicle under the starting conditions by posi-
tioning the gear lever in neutral.II - TEST OPERATION
aActivate the starter until the needle of the petrol
compression gauge stabilises.
aMeasure the cylinder compressions, cylinder by cyl-
inder.
aFully depress the accelerator pedal in order to open
the throttle valve during the compression measure-
ments.
III - FINAL OPERATION
aDisconnect the petrol compression gauge.
aRefit the plugs (see 17A, Ignition, Plugs: Removal
- Refitting, page 17A-12) .
aRun command VP037: "STOP INHIBIT FUEL SUP-
PLY" using the Diagnostic tool.
aStart the engine. Equipment required
petrol compression gauge
Diagnostic tool
Note:
Use a petrol compression gauge compatible with
the special tools.
The petrol compression gauge must be equipped
with a universal end piece (rubber), or a gaz 1/4
thread bolt.
132699
Note:
It is necessar y to wait for at least 10 seconds
before starting the engine each time (the starter
will not run due to its ther mal protection).
Note:
If the engine does not start, run command
VP037: STOP FUEL SUPPLY INHIBITION using
the Diagnostic tool or switch off the ignition and
wait 1 min before starting the engine again.

11A-28
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D7F, and 800
11A
aRemove the cap (3) from the upper timing cover.
aTurn the engine clockwise (timing end) until the
mark on the camshaft sprocket is aligned with the
mark on the upper timing cover.
aInsert the TDC setting pin (Mot. 1054) (4)
aRemove the ignition interference suppressor.
aDisconnect the fuel supply pipe.
aRemove the following covers:
-upper timing,
-middle timing,-lower timing.
II - REMOVAL OF PART CONCERNED
aMake a marking on the rocker cover (5) in line with
the camshaft sprocket mark
aUndo the tensioning roller nut (6) .
aRemove the timing belt.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aLine up the marks on the timing belt with those on
the camshaft sprocket and crankshaft sprocket.
aRefit:
-the new timing belt,
-the new tensioning roller.
aTighten the tensioning roller.
aRemove the TDC setting rod (Mot. 1054).
107259
99795
1041

11A-31
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see ) (80A, Battery).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the rear suspended engine mounting (see 19D,
Engine mounting, Lower engine tie-bar: Re-
moval - Refitting, page 19D-18) .aSet up the engine support tool (Mot. 1379), shifting
the engine forwards.
aLift the engine slightly using the (Mot. 1379).
aRemove:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) .
aRefit the crankshaft accessories pulley bolt.
aUnclip the fuel pipe from the upper timing cover. Special tooling required
Mot. 1379Engine suppor t tool for cylin-
der head oper ations.
Mot. 1054TDC setting pin.
Tightening torquesm
tensioning roller nut24 N.m
lower timing cover bolt10 N.m
intermediate timing
cover bolts10 N.m
upper timing cover bolts37 N.m
10267

11A-37
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
aCheck that the tensioning roller does not come into
contact with the cylinder head.
aIf the tensioning roller is in contact with the cylinder
head:
-set the engine to Top Dead Centre,
-remove the tensioning roller and the timing belt,
-insert the tensioning roller pin,
-repeat the timing belt refitting method from the be-
ginning, step by step.
III - FINAL OPERATION
aRefit:
-the lower timing cover,
-the lower timing cover bolt,
-the timing intermediate housing,
-the intermediate timing cover bolts,
-the upper timing cover,
-the upper timing cover.
aTorque tighten:
-the lower timing cover bolt (10 N.m),
-the intermediate timing cover bolts (10 N.m),
-the upper timing cover bolts (37 N.m)aFit the oil pressure sensor connector.
aClip the oil pressure sensor wiring on the upper tim-
ing cover.
aConnect the oil pressure sensor connector.
aFit the flexible heat shield on the oil pressure sensor
connector.
aClip the fuel pipe on to the upper timing cover.
aRefit:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the rear suspended engine mounting (see 19D,
Engine mounting, Lower engine tie-bar: Re-
moval - Refitting, page 19D-18) .
aRemove the tool (Mot. 1379).
aRefit:
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aConnect the battery (see ) (80A, Battery).
109765
D4F, and 780 or 782

11A-53
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K4M
11A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove:
-the engine undertray,
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the headlights (see Halogen headlight: Removal
- Refitting) (80B, Headlights),
-the bonnet catch (see Bonnet lock: Removal -
Refitting) (52A, Non-side opening element mecha-
nisms),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the throttle valve (see 12A, Fuel mixture, Throttle
valve: Removal - Refitting, page 12A-20) ,
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment), Special tooling required
Mot. 1489TDC locating pin.
Mot. 1368Tool for tightening eccentric
tensioning roller bolt. 8 mm
Torx wrench and 12.7 mm
square.
Mot. 1496Camshaft timing tool.
Mot. 1750Additional tool to suppor t the
camshaft adjusting tool, Mot.
1496.
Mot. 1490-01For locking and adjusting the
camshaft pulle ys.
Mot. 1487Tool for refitting camshaft cov-
ers (57 mm diameter).
Mot. 1488Tool for refitting camshaft cov-
ers (43 mm diameter).
Equipment required
indelible pencil
Tightening torquesm
fixed roller bolt50 N.m
lower timing cover bolts12 N.m
exhaust camshaft pul-
ley nut30 N.m + 84˚
camshaft dephaser pul-
ley bolt100 N.m
timing tension wheel nut27 N.m
TDC setting pin plug20 N.m
upper timing cover bolts41 N.m
upper timing cover nuts41 N.m
rear suspended engine
reinforcement bolt105 N.m
rear suspended engine
mounting bolt on the
rear suspended engine
mounting suppor t105 N.m
rear suspended engine
mounting bolt on the
subframe105 N.m Tightening torquesm

11A-64
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K4M
11A
aRefit the lower timing cover flap, checking that the
locating pin (34) fits properly in the notch (35) .
III - FINAL OPERATION
aRefit:
-a new inlet camshaft plug using the (Mot. 1487),
-a new exhaust camshaft plug using the (Mot.
1488),
-the lifting eye.
aClip the wiring onto the lifting eye.aPlace a drop of SILICONE ADHESIVE SEALANT
(see Vehicle: Parts and consumables for the re-
pair) (04B, Consumables - Products) on the thread
of the TDC setting pin plug.
aTorque tighten the TDC setting pin plug (20 N.m).
aRefit the upper timing cover.
aTorque tighten:
-the upper timing cover bolts (41 N.m),
-the upper timing cover nuts (41 N.m).
aPosition the wiring of the upstream oxygen sensor.
aAttach the upstream oxygen sensor wiring.
aConnect the upstream oxygen sensor connector.
aRefit:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the rear suspended engine mounting.
aTorque tighten:
-the rear suspended engine reinforcement bolt
(105 N.m),
-the rear suspended engine mounting bolt on
the rear suspended engine mounting support
(105 N.m),
-the rear suspended engine mounting bolt on
the subframe (105 N.m).
aRefit:
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the throttle valve (see 12A, Fuel mixture, Throttle
valve: Removal - Refitting, page 12A-20) ,
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
109052
14890

11A-66
TOP AND FRONT OF ENGINE
Rocker cover: Removal - Refitting
D7F
11A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery ( (see Battery: Removal -
Refitting) ).
aRemove:
-the intake distributor (see 12A, Fuel mixture, Inlet
distributor: Removal - Refitting, page 12A-29) ,
-the air filter box (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) .
aUnclip:
-The harness from the heat shield,
-the brake servo pipe from the heat shield.
aDisconnect the ignition coil supply.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the rocker cover bolts,
-the rocker cover.ON THE WORKBENCH
aRemove:
-the ignition coil,
-the heat shield.
REFITTING
I - REFITTING PREPARATIONS OPERATION
ON THE WORKBENCH
aRefit:
-the heat shield,
-the ignition coil.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the rocker cover,
-the rocker cover bolts.
aTorque tighten the rocker cover bolts (10 Nm).
III - FINAL OPERATION.
aConnect the ignition coil supply.
aClip:
-the brake servo pipe onto the heat shield,
-the harness onto the heat shield.
aRefit:
-the air filter box (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the intake distributor (see 12A, Fuel mixture, Inlet
distributor: Removal - Refitting, page 12A-29) .
aConnect the battery ( (see Battery: Removal - Re-
fitting) ). Tightening torquesm
rocker cover bolts10 Nm
110422