heater RENAULT TWINGO 2009 2.G Engine And Peripherals Service Manual

19A-7
COOLING
Engine cooling system: Operating diagram
D4F, and 780 or 782
19A
122824
(1) Engine
(2) Radiator
(3) Heater matrix
(4) Expansion bottle
(5) Coolant pump
(6) Thermostat
(7) Bleed screws
(8) 10 mm restr iction
(9) Turbocharger
Note:
The rating of the expansion bottle degassing valve
is 1.4 bar.

19A-8
COOLING
Engine cooling system: Operating diagram
K4M
19A
128623
(1) Engine
(2) Cooling radiator
(3) Heater matrix
(4) Expansion bottle
(5) Water pump
(6) Thermostat
(7) Bleed screws
(8) Chok e

19A-34
COOLING
Thermostat: Removal - Refitting
D4F, and 772 – D7F
19A
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
aParts always to be replaced :
-water chamber seal.
aConsumable (see 04B, Parts and consumables
for the repair):
-COOLANT.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the air filter unit (see 12A, Fuel mixture,
Air filter unit: Removal - Refitting, page 12A-13) .
aRemove the air filter box inlet pipe .
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
aClean the cooling system if necessary (see 19A,
Cooling, Cooling system: Draining - Refilling,
page 19A-9) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aSeparate the clips on the water chamber top hose
and the heater matrix hose on the water chamber
using the tool (Mot. 1448).
aDisconnect the water chamber top hose and the
heater matrix hose on the water chamber.aRemove:
-the water chamber bolts (1) ,
-the cylinder head water chamber.
REFITTING
I - REFITTING PREPARATION OPERATION
a
aIt is imperative to replace the cylinder head water
chamber seal.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the cylinder head water chamber,
-the cylinder head water chamber bolts.
aConnect the water chamber top hose and the heater
matrix hose on the water chamber.
aFit the clips of the water chamber top hose and the
heater matrix hose on the water chamber using the
tool (Mot. 1448). Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
D4F
D7F
113372
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).

19A-46
COOLING
Water chamber: Removal - Refitting
D4F, and 780 or 782
19A
REMOVAL - REFITTING
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDetach the turbocharger cooling pipe from the cylin-
der head.
aRemove the water chamber hose clips using the
(Mot. 1448).
aDisconnect the water chamber hoses.
aRemove the pipe from the heater matrix under the
water chamber.aRemove:
-the water chamber bolts (1) ,
-the water chamber (2) ,
-the water chamber seal.
REFITTING
I - REFITTING PREPARATION OPERATION
aAlways replace the water chamber seal.
II - REFITTING OPERATION FOR PART
CONCERNED
aPosition the water chamber with a new seal.
aScrew on the water chamber bolts without tightening
them.
aTorque tighten the water chamber bolts (10 N.m).
aConnect the water chamber hoses.
aFit the heater matrix pipe under the water chamber.
aRefit the water chamber hose clips using the (Mot.
1448).
aClip the turbocharger cooling pipe onto the cylinder
head. Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
Tightening torquesm
water chamber bolts10 N.m
Note:
Use a cloth to protect the TDC sensor to prevent
any coolant entering the opening on the gearbox.
113372
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).

19A-48
COOLING
Water chamber: Removal - Refitting
K4M
19A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the engine undertray.
aDrain the cooling system (see 19A, Cooling, Cool-
ing system: Draining - Refilling, page 19A-9) . Special tooling required
Mot. 1448Remote operation pliers for
hose clips .
Mot. 1202-01Clip pliers for hose clips
(large size).
Mot. 1202-02Clip pliers for hose clips
(small size)
Tightening torquesm
water chamber bolts
(initial torque)4 N.m
water chamber bolts12 N.m
heater matrix hose
bracket bolt10 N.m
IMPORTANT
When working in the engine compartment, take
care as the radiator fan(s) may start up unexpect-
edly (risk of being cut).
To avoid any risk of serious burns when the engine
is hot:
-do not open the expansion bottle cap,
-do not drain the cooling system,
-do not open the bleed screw(s).
WARNING
When carr ying out a repair that requires a complete
change, it is essential to flush the circuit with clean
water, blast compressed air through the circuit to
drive out the water, fill and bleed the circuit and
then measure the effective protection.
The cr iteria to be met are:
-protection down to -25˚C ±± ± ±
2 for cold and temper-
ate countries,
-protection down to -40˚C ±± ± ±
2 for "extreme cold"
countries.
WARNING
Before the operation, protect the electrical accesso-
ries to prevent any risk of shor t circuiting and pro-
tect the belts to avoid damaging them.

19A-49
COOLING
Water chamber: Removal - Refitting
K4M
19A
aUsing the (Mot. 1448) or (Mot. 1202-01) or (Mot.
1202-02) remove:
-the cooling radiator top hose clip on the water
chamber,
-the heater matrix hose clip (1) on the water cham-
ber.
aDisconnect from the water chamber:
-the cooling radiator top hose,
-the heater matrix hose.
aRemove:
-the bolt (2) from the heater matrix hose bracket,
-the heater matrix hose bracket,
-the bolts (3) of the engine wiring channel,
-the coolant temperature sensor (see 19A, Cool-
ing, Coolant temperature sensor: Removal - Re-
fitting, page 19A-66) .
aMove aside the engine wiring channel.
aUnclip the wiring at (4) .II - REMOVAL OPERATION
aRemove:
-the coolant outlet unit bolts,
-the water chamber,
-the water chamber seal.
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: Cylinder head cool-
ant outlet unit seal.
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease:
-the cylinder head joint face,
-the coolant outlet unit housing if it is being reused.
132444
128456
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).

19A-50
COOLING
Water chamber: Removal - Refitting
K4M
19A
II - REFITTING OPERATION
aRefit the coolant outlet unit with a new seal.
aPretighten in order and to torque the water cham-
ber bolts (initial torque) (4 N.m).
aTorque tighten in order the water chamber bolts
(12 N.m).
III - FINAL OPERATION
aClip the wiring onto the water chamber.
aFit the engine wiring channel.
aRefit:
-the coolant temperature sensor (see 19A, Cool-
ing, Coolant temperature sensor: Removal - Re-
fitting, page 19A-66) ,
-the heater matrix hose bracket.
aTorque tighten the heater matrix hose bracket bolt
(10 N.m).
aConnect to the coolant outlet unit:
-the heater matrix hose,
-the cooling radiator top hose.
aUsing the (Mot. 1448) or (Mot. 1202-01) or (Mot.
1202-02) fit:
-the heater matrix hose clip,
-the cooling radiator top hose clip.
aRefit the air filter unit (see 12A, Fuel mixture, Air fil-
ter unit: Removal - Refitting, page 12A-13) .aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .
aRefit the engine undertray.
128456