radiator RENAULT TWINGO 2009 2.G Engine And Peripherals Workshop Manual

Contents
13C PREHEATING
Pre-postheating unit:
Removal - Refitting 13C-1
Heater plugs: Removal -
Refitting 13C-2
14A ANTIPOLLUTION
Oil vapour rebreathing
circuit: Descriptions 14A-1
Fuel vapour recirculation
circuit: Operating diagram 14A-2
Fuel vapour recirculation
circuit: Check 14A-3
Fuel vapour absorber:
Removal - Refitting 14A-4
Fuel vapour absorber: Check 14A-7
Fuel vapour absorber bleed
solenoid valve: Removal -
Refitting 14A-8
Exhaust gas recirculation
solenoid valve: Removal -
Refitting 14A-10
Exhaust gas cooler: Removal
- Refitting 14A-11
Exhaust gas recirculation
assembly: Removal -
Refitting 14A-15
Exhaust gas recirculation
rigid pipe: Removal -
Refitting 14A-19
16A STARTING - CHARGING
Alternator: Removal -
Refitting 16A-1
Star ter: Removal - Refitting 16A-10
Alternator pulley: Removal -
Refitting 16A-1717A IGNITION
Coils: Removal - Refitting 17A-1
Plugs: Removal - Refitting 17A-12
17B PETROL INJECTION
Petrol injection: List and
location of components 17B-1
Oxygen sensors: Removal -
Refitting 17B-13
Petrol injection computer:
Removal - Refitting 17B-20
Pinking sensor: Removal -
Refitting 17B-23
Crankshaft position sensor:
Removal - Refitting 17B-25
Injector rail - Injectors:
Removal - Refitting 17B-27
19A COOLING
Engine cooling system:
Specifications 19A-1
Engine cooling system:
Check 19A-2
Engine cooling circuit: List
and location of components 19A-4
Engine cooling system:
Operating diagram 19A-5
Cooling system: Draining -
Refilling 19A-9
Cooling radiator: Removal -
Refitting 19A-12
Coolant pump: Removal -
Refitting 19A-24
Thermostat: Removal -
Refitting 19A-34
Water chamber: Removal -
Refitting 19A-40

10A-9
ENGINE AND CYLINDER BLOCK ASSEMBLY
Lower cover: Removal - Refitting
K9K
10A
aLoosen the lower bolts (7) of the subframe front tie
rods.
aRemove the upper bolts (8) of the subframe front tie
rods.
aRemove:
-the nuts (9) from the track rod ends,
-the track rod ends using the (Tav. 476),
-the bolts (10) from the lower ball joints,
-the lower ball joints.aRemove:
-the subframe rear tie rod inner bolts (11) ,
-the subframe rear tie rod outer bolts (12) .
aAttach the radiator and the intercooler to the upper
cross member using a safety strap(s).
aAttach the radiator to the upper cross member using
a safety strap(s).
aRemove the radiator mounting cross member (see
Radiator mounting cross member: Removal -
Refitting) (41A, Front lower structure).
119210
119222
119335
K9K, and 718
K9K, and 740

10A-12
ENGINE AND CYLINDER BLOCK ASSEMBLY
Lower cover: Removal - Refitting
K9K
10A
-the subframe rear bolts (105 Nm),
-the subframe rear tie rod inner bolts (21 N.m),
-the subframe rear tie rod outer bolts (90 N.m).
aRefit the radiator mounting cross member (see Ra-
diator mounting cross member: Removal - Refit-
ting) (41A, Front lower structure).
aDetach the radiator and the intercooler from the up-
per cross member using a safety strap(s).
aDetach the radiator from the upper cross member
using a safety strap(s).
aRefit:
-the rear engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the lower ball joints,
-the track rod ends.
aTighten to torque:
-the lower ball joint bolts (62 N.m),
-the track rod end nuts (37 N.m).
aRefit the subframe tie rod upper bolts.
aTighten to torque:
-the subframe tie-rod upper bolts (21 N.m),
-the subframe tie-rod lower bolts (62 N.m).
aRefit the front right-hand driveshaft relay bearing
aTighten to torque:
-the bolts of the front right-hand driveshaft relay
bearing (44 N.m),
-the bolt of the front right-hand driveshaft relay
bearing bracket (21 N.m).aFit the relay bearing on its bearing on the front right-
hand driveshaft.
aTorque tighten the relay bearing bolts on the front
right-hand driveshaft (44 N.m).
aRefit the closure panel of the front right-hand drive-
shaft relay bearing
aTorque tighten the right-hand driveshaft relay
bearing closure panel bolts (21 Nm).
aRefit the catalytic converter upstream stay, by slid-
ing it in relation to the bolt remaining on the sump.
aTighten the following until contact is made and to tor-
que:
-the catalytic converter upstream stay bolt on
the cylinder block (44 N.m),
-the catalytic converter downstream stay bolt on
the sump (44 Nm),
-the catalytic converter downstream stay bolts
on the catalytic converter (26 Nm).
aFit the steering box universal joint equipped with a
new bolt.
aTorque tighten the universal joint bolt (24 N.m).
aRemove the flywheel immobiliser.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aFill up the engine oil (see 10A, Engine and cylinder
block assembly, Engine oil: Draining - Refilling,
page 10A-22) . K9K, and 718
K9K, and 740
K9K, and 718
K9K, and 740
Note:
Ensure that the right-hand dr iveshaft relay bear-
ing closure panel is refi tted the right way round.

10A-15
ENGINE AND CYLINDER BLOCK ASSEMBLY
Lower cover: Removal - Refitting
D4F or D7F
10A
aAttach the cooling radiator to the upper cross mem-
ber.
aRemove:
-the bolts (6) from the front end cross member,
-the subframe bolts (7) .
aRemove the threaded rods of the (Tav. 1233-01)
one by one, replacing them with the subframe
mounting bolts.
aLower the subframe by several centimetres, gradu-
ally loosening the nuts of the (Tav. 1233-01).II - OPERATION FOR REMOVAL OF PART
CONCERNED
1 - Removing the sump with silicone adhesive
sealant
aRemove the sump bolts.
aGradually remove the sump using the (Mot. 1716).
aRemove the sump by pivoting it anti-clockwise to
prevent catching the oil pump strainer.
2 - Removing the sump with an After-Sales seal
aRemove:
-the sump bolts,
-the sump by pivoting it anti-clockwise to prevent
catching the oil pump strainer,
-the sump seal.
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: engine oil sump
seal.
aUse SUPER CLEANING AGENT FOR JOINT FA-
CES (see Vehicle: Parts and consumables for
the repair) (04B, Consumables - Products) to clean
the joint faces:
-of the cylinder block,
-of the sump.
aLeave for approximately ten minutes.
aRemove the residue using a wooden spatula.
aFinish cleaning the parts using a GREY ABRASIVE
PAD (see Vehicle: Parts and consumables for
the repair) (04B, Consumables - Products).
aUse SURFACE CLEANER (see Vehicle: Parts
and consumables for the repair) (04B, Consuma-
bles - Products) to clean and degrease the joint fa-
ces:
-of the cylinder block,
-of the sump.
119336
Note:
This operation requires two people.
Note:
Make sure the threaded rod of the (Tav. 1233-01)
is sufficiently screwed into the threaded hole and
that the nut of the tool is properly resting on the
subframe.
WARNING
The joint faces must be clean, dr y and free from
grease (avoid finger marks).

10A-20
ENGINE AND CYLINDER BLOCK ASSEMBLY
Lower cover: Removal - Refitting
K4M
10A
aUse SILICONE ADHESIVE SEALANT (see Vehi-
cle: Parts and consumables for the repair) (04B,
Consumables - Products) to apply:
-a bead at (4) ,
-a drop at (5) at the joint between the cylinder block
and crankshaft closure panel.II - REFITTING OPERATION
aRefit:
-a new sump seal,
-the sump in the direction of the arrows.
aFinger tighten the sump bolts on the cylinder block.
aFinger tighten the 4 sump bolts on the gearbox
housing.
20167
20166
WARNING
Applying excess sealant could cause it to be
squeezed out when parts are tightened. A mix-
ture of sealant and fluid could damage certain
components (engine, radiator, etc.).
145657

10A-37
ENGINE AND CYLINDER BLOCK ASSEMBLY
Conrod bearing shell: Removal - Refitting
K9K
10A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the engine undertray.
aDrain the oil from the engine (see 10A, Engine and
cylinder block assembly, Engine oil: Draining -
Refilling, page 10A-22) .
aRemove the oil filter (see 10A, Engine and cylinder
block assembly, Oil filter: Removal - Refitting,
page 10A-29) .
aRemove the lower engine tie-bar (see 19D, Engine
mounting, Lower engine tie-bar: Removal - Refit-
ting, page 19D-18) .
aStrap the radiator to the vehicle using safety
strap(s).
aRemove the front axle subframe (see Front axle
subframe: Removal - Refitting) (31A, Front axle
components).
aRemove the relay bearing of the front right-hand
wheel driveshaft. Special tooling required
Mot. 1914Tool for fitting G9 con rod
bear ing shells
Mot. 1920Tool for fitting F9 / K9 con rod
bear ing shells
Equipment required
safety strap(s)
component jack
indelible pencil
torque wrench
Diagnostic tool
Tightening torquesm
con rod cap bolts20 N.m + 45˚ ±± ± ±
6˚
oil pump bolts25 N.m
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair (see Vehicle: Precautions for the repair) .
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
123838

10A-43
ENGINE AND CYLINDER BLOCK ASSEMBLY
Conrod bearing shell: Removal - Refitting
K9K
10A
II - REMOVAL - REFITTING OPERATIONS FOR THE
CON ROD BEARING SHELLS ON CYLINDERS
NO.3, 1 AND 4
aPerform the same removal - refitting operations as
for the con rod bearing shells on cylinder no. 2.
III - FINAL OPERATION
aparts always to be replaced: engine oil sump
seal
parts always to be replaced: Oil filter
parts always to be replaced: Drain plug seal on
engine oil sump
aUse a wooden spatula or an ABRASIVE PAD to
clean the joint face of the cylinder block and engine
oil sump.
aRefit the oil pump.
aFit without tightening the oil pump bolts, while keep-
ing a clearance of 3 mm to 5 mm.
aFit the engine oil sump seal.aApply SILICONE ADHESIVE SEALANT (see Vehi-
cle: Parts and consumables for the repair) :
-four beads with a diameter of 5 mm at (A) ,
-two drops with a diameter of 5 mm at (B) .
aFit the engine oil sump while supporting it using a
component jack. Note:
For removing and refitting the con rod bearing
shells on cylinders no. 1 and no. 4, position the
pistons at Bottom Dead Centre before performing
the same removal and refitting operations as for
the con rod bearing shells on cylinder no. 2.
WARNING
Do not scrape the joint faces of the aluminium,
any damage caused to the joint face will result in
a risk of leaks.
WARNING
To ensure proper sealing, the gasket surfaces
must be clean, dry and not greasy (avoid any fin-
ger marks).
WARNING
Applying excess sealant could cause it to be
squeezed out when parts are tightened. A mix-
ture of sealant and fluid could damage certain
components (engine, radiator, etc.).
20166
20167

10A-44
ENGINE AND CYLINDER BLOCK ASSEMBLY
Conrod bearing shell: Removal - Refitting
K9K
10A
aTilt the engine oil sump forwards in order to access
the oil pump bolts.
aTorque tighten the oil pump bolts (25 N.m) using
the torque wrench PROSTEEL, part number 77 11
226 888 starting with the 13 mm bolt.
a
aRefit the engine oil sump bolts.
aTorque tighten in order the engine oil sump bolts
(see 10A, Engine and cylinder block assembly,
Lower cover: Removal - Refitting, page 10A-6) .
aRefit the catalytic converter upstream stay (see 19B,
Exhaust, Catalytic converter: Removal - Refit-
ting, page 19B-12) .
aConnect the connector to the oil level sensor.
aRefit the relay bearing of the front right-hand wheel
driveshaft (see Front right-hand driveshaft: Re-
moval - Refitting) .
aRefit the front axle subframe (see Front axle sub-
frame: Removal - Refitting) (31A, Front axle com-
ponents).
aRemove the safety strap(s) from the radiator.
aRefit the lower engine tie-bar (see 19D, Engine
mounting, Lower engine tie-bar: Removal - Refit-
ting, page 19D-18) .aDisconnect the crankshaft position sensor (4) to pre-
vent the engine from starting.
aRefit the oil filter (see 10A, Engine and cylinder
block assembly, Oil filter: Removal - Refitting,
page 10A-29)
aFill up the engine oil (see 10A, Engine and cylinder
block assembly, Engine oil: Draining - Refilling,
page 10A-22) .
aStart the engine using the starter until the engine oil
warning light goes out.
aConnect the crankshaft position sensor.
aRefit the engine undertray.
aClear the present faults using the Diagnostic tool.
140918
Note:
Check that the engine oil sump seal is definitely
in place before tightening the engine oil sump
bolts.
123824

10A-76
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine - gearbox assembly: Removal - Refitting
D4F or D7F
10A
aRemove the bolt (4) from the expansion bottle.
aMove the expansion bottle aside following the ar-
rows (5) and (6) .
aRemove:
-the air filter box air inlet pipe from the cross mem-
ber,
-the air filter unit air inlet pipe,
-the cooling radiator upper bolts. JH3
120514
D4F or D7F, and 772

10A-84
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine - gearbox assembly: Removal - Refitting
D4F or D7F
10A
aRefit:
-the air conditioning pipe bolt on the dehydrator res-
ervoir,
-the air conditioning pipe bolts on the compressor.
aTighten:
-the air conditioning pipe bolts on the dehydrator
reservoir,
-the air conditioning pipe bolts on the compressor.
aFill the refrigerant circuit (see Refrigerant circuit:
Draining - Filling) (62A, Air conditioning).
aConnect:
-the petrol vapour rebreathing solenoid valve con-
nector,
-the brake servo pipe on the brake servo,
-the heater matrix hoses.
aFit the cooling unit.
aRefill:
-the engine oil, if necessary (see 10A, Engine and
cylinder block assembly, Engine oil: Draining -
Refilling, page 10A-22) ,
-the gearbox oil (see Manual gearbox oils: Drain-
ing - Filling) ,
-and bleed the cooling system (see 19A, Cooling,
Cooling system: Draining - Refilling, page 19A-
9) .
aRefit:
-the air filter unit air inlet pipe,
-the air filter unit air inlet pipe bolt on the cross
member.
aConnect the air filter box air inlet pipe on the air filter
box cover.
aRefit the turbocharger outlet air pipe.
aPush the intercooler air inlet pipe clip.
aConnect the intercooler air inlet pipe on the inter-
cooler.aPush the turbocharger outlet air pipe clip, following
the direction shown by the arrow (23) .
aConnect the turbocharger air outlet pipe onto the tur-
bocharger.
aRefit the turbocharger outlet rigid air pipe bolt on the
throttle valve.
aConnect the intercooler air outlet pipe to the inter-
cooler.
aTighten the intercooler air outlet pipe clip.
aRefit:
-the cooling radiator upper bolts.
-the air filter unit air inlet pipe,
-the air filter box air inlet pipe on the cross member,
aPosition the expansion bottle.
aRefit the expansion bottle bolt.
aClip the bonnet opening release cable on to the cool-
ing fan assembly.
aPosition the earth straps.
aRefit the earth strap nuts on the front right-hand side
member. D4F, and 780 or 782
122666
D4F or D7F, and 772