recommended oil RENAULT TWINGO 2009 2.G Engine And Peripherals Workshop Manual

10A-24
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine oil: Draining - Refilling
D4F or D7F
10A
Copper seal
aRefit the new seal on the plug, positioning the
groove towards the plug.
aTorque tighten the drain plug (20 N.m) using
torque wrench and a oil change end piece with
an 8 mm square drive.
II - FILLING
aFill the engine with oil, observing the recommended
amount.
aWait at least 10 minutes.
aCheck the oil level using the dipstick.
aTop up the engine oil level if necessary.
aRefit:
-the engine oil filler cap,
-the dipstick.
113764

10A-26
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine oil: Draining - Refilling
K4M
10A
III - DRAINING
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the engine oil filler cap (1) ,
-the dipstick (2) ,
-the engine undertray bolts,
-the engine undertray.
aPlace the oil recovery tray under the engine.aRemove the drain plug (3) from the engine oil sump
using the oil change wrench.
aLet the engine oil run into the oil recovery tray.
aRemove the drain plug seal.
aFit a new seal onto the engine oil drain plug.
aTorque tighten the engine oil sump drain plug (20
N.m) using a torque wrench and a oil change end
piece with an 8 mm square drive.
aWipe the oil drips on the sump using a cloth.
aRemove the oil recovery tray.
aRefit the engine undertray.
IV - FILLING
aPosition the vehicle back on the ground.
aFill the engine with oil, observing the recommended
amount.
aWait at least 10 minutes.
aCheck the oil level using the dipstick.
aTop up the engine oil level if necessary.
aRefit:
-the dipstick,
-the engine oil filler cap.
132431
18749

10A-28
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine oil: Draining - Refilling
K9K
10A
III - OIL SERVICE
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the engine oil filler cap (1) ,
-the dipstick (2) ,
-the engine undertray bolts,
-the engine undertray.
aPlace the oil recovery tray under the engine.aRemove the drain plug (3) from the engine oil sump
using the (Mot. 1018) or a oil change wrench.
aLet the engine oil flow out.
aRemove the drain plug seal.
aRefit the new seal to the drain plug.
aTorque tighten the drain plug (20 N.m) using a oil
change wrench and a oil change end piece with
an 8 mm square drive.
aWipe the oil drips around the drain plug using a
cloth.
aRemove the oil recovery tray.
aRefit the engine undertray.
IV - FILLING
aPosition the vehicle back on the ground.
aFill the engine with oil, observing the correct quantity
of oil as recommended by the manufacturer.
aWait at least 10 minutes.
aCheck the oil level using the dipstick.
aTop up the engine oil level if necessary.
aRefit:
-the engine oil filler cap,
-the dipstick.
120041
120042

10A-32
ENGINE AND CYLINDER BLOCK ASSEMBLY
Oil filter: Removal - Refitting
K4M
10A
aWipe any oil run-off with a cloth.
aTop up the engine oil with oil recommended by the
manufacturer (see Engine oil: Specifications)
(Technical Note 6013A, 04A, Lubricants).
aConnect the battery (see Battery: Removal - Refit-
ting) (80A, Battery).
aStart the engine and wait until the oil pressure warn-
ing light goes out on the instrument panel.
aCheck for leaks from the oil filter.
aRefit the engine undertray.
aWait at least 10 minutes.
aCheck the oil level using the dipstick.
aAdjust the engine oil level if necessary.WARNING
Always check the oil level using the dipstick.
Do not exceed the maximum level on the dipstick
(could destroy the engine).
Correct the engine oil level if necessary before
delivering the vehicle to the customer.

10A-93
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine - gearbox assembly: Removal - Refitting
K9K
10A
II - FINAL OPERATION
aRemove the.
aLubricate the seals using recommended air condi-
tioning oil to make fitting easier.
aRefit:
-the connecting pipes to the compressor,
-the connecting pipe union bolts on the compressor,
-the bolt for the connecting pipe mounting on the
compressor.
aConnect:
-the pressostat connector,
-the hose to the coolant pump inlet pipe using the
tool (Mot. 1448).
aFit:
-the hose clip on the coolant pump inlet pipe using
the tool (Mot. 1448),
-the earth on the front left-hand wing.
aRefit the earth nut on the front left-hand wing.
aClip:
-the engine compartment connection unit relay
plates,
-the fuse holders.
aRefit the fuses.
aConnect the preheating unit connector.
aRefit the earth nut on the front left-hand side mem-
ber.
aFit the engine compartment connection unit.
aRefit the engine compartment connection unit
mountings on the body.
aConnect the black connector.
aClip on the black connector.
aRefit:
-the engine compartment connection unit cover,
-a new clip on the battery mounting to hold the elec-
trical wiring.
aConnect the wiring connectors to the fan assembly.aClip the fan assembly wiring.
aRemove the blanking plugs.
aConnect the high pressure pump inlet pipe.
aClip on the fuel supply pipe.
aConnect the high pressure pump return pipe.
aClip on the fuel return pipe.
aRemove the blanking plugs on the clutch hydraulic
control and on the control pipe.
aConnect the clutch hydraulic control to the gearbox.
aClip:
-the clutch control hydraulic pipe on the gearbox,
-the gearbox controls on the cable sleeve stops,
-the gearbox controls on the gear selectors.
aConnect:
-the hoses to the heater radiator,
-the top hose to the water chamber.
aFit:
-the hose clips on the heater radiator using the tool
(Mot. 1448),
-the clip for the top hose on the water chamber us-
ing the tool (Mot. 1448).
aRefit:
-the front section of the intermediate pipe (see 19B,
Exhaust, Intermediate pipe: Removal - Refit-
ting, page 19B-28) ,
-the front right-hand wheel driveshaft (see Front
right-hand driveshaft: Removal - Refitting)
(29A, Driveshafts),
-the front left-hand wheel driveshaft (see Front left-
hand driveshaft: Removal - Refitting) (29A,
Driveshafts),
-the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(41A, Front lower structure),
-the front axle subframe (see Front axle subframe:
Removal - Refitting) (31A, Front axle compo-
nents),
-the engine tie-bar (see 19D, Engine mounting,
Lower engine tie-bar: Removal - Refitting, page
19D-18) . WARNING
To prevent any leaks, check that the seal and the
surface of the pipe are in good condition. The
seal and the surface must be clean and scratch
free.

19A-17
COOLING
Cooling radiator: Removal - Refitting
K9K
19A
-the top hose on the radiator,
-the bottom hose on the radiator.
a
aLubricate the seals with the recommended air condi-
tioning oil to facilitate fitting.
aFit the condenser connecting pipes.
aFit the connecting pipe unions to the condenser.
aRefit the plastic cover on the condenser.
aConnect the pressostat connector.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
aConnect the battery (see ) (80A, Battery).
aFill and bleed the cooling system (see 19A, Cool-
ing, Cooling system: Draining - Refilling, page
19A-9) .aCheck that the system is operating correctly (see Air
conditioning: Check) (62A, Air conditioning).
aFill the refrigerant circuit using a refrigerant charg-
ing station (see Refrigerant circuit: Draining -
Filling) (62A, Air conditioning).
aCheck the refrigerant circuit (see Refrigerant cir-
cuit: Check) (62A, Air conditioning). AIR CONDITIONING
WARNING
Do not remove the blanking plugs from each
component until the last moment.
Also, do not remove the components from their
packaging until they are to be fitted to the vehi-
cle.
WARNING
To avoid any leaks, check that the seal and the
pipe surface are in good condition. The seal and
the surface must be clean and scratch free.
AIR CONDITIONING