service RENAULT TWINGO 2009 2.G Engine And Peripherals Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO, Model: RENAULT TWINGO 2009 2.GPages: 652
Page 1 of 652
© Renault s.a.s 2007 "The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the manufacturer in
the production of the various component units and accessories from which the vehicles are
constructed".All rights reserved by Renault.
Copying or translating, in part or in full, of this document or use of the service part reference
numbering system is forbidden without the prior written authority of Renault.
NOVEMBER 2009 EDITION ANGLAISE
X44
1Engine and peripherals
10AENGINE AND CYLINDER BLOCK ASSEMBLY
11ATOP AND FRONT OF ENGINE
12AFUEL MIXTURE
12BTURBOCHARGING
13AFUEL SUPPLY
13BDIESEL INJECTION
13CPREHEATING
14AANTIPOLLUTION
16ASTARTING - CHARGING
17AIGNITION
17BPETROL INJECTION
Page 2 of 652
© Renault s.a.s 2007 "The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the manufacturer in
the production of the various component units and accessories from which the vehicles are
constructed".All rights reserved by Renault.
Copying or translating, in part or in full, of this document or use of the service part reference
numbering system is forbidden without the prior written authority of Renault.
NOVEMBER 2009 EDITION ANGLAISE
X44
19ACOOLING
19BEXHAUST
19CTANK
19DENGINE MOUNTING
Page 28 of 652
10A-22
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine oil: Draining - Refilling
D4F or D7F
10A
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
aParts always to be replaced :
-copper seal.aConsumable (see Vehicle: Parts and consuma-
bles for the repair) (04B, Consumables - Products).
-Engine oil (see Engine oil: Specifications) (Tech-
nical Note 6013A, 04A, Lubricants).
I - OIL SERVICE
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment). Special tooling required
Mot. 10188 mm square engine drain
plug spanner.
Equipment required
oil change wrench
oil recovery tray
torque wrench
oil change end piece with an 8 mm square drive
Tightening torquesm
drain plug20 N.m
EngineAverage oil capacity
(adjusting using dipstick) (l)
Oil change with-
out filter
replacementOil change with
filter replace-
ment
D7F
3.8 4
D4F
WARNING
Always check the oil level using the dipstick.
Do not exceed the maximum level on the dipstick
(could destroy the engine).
Correct the engine oil level if necessary before
deliver ing the vehicle to the customer.
Note:
When topping up the engine oil, always leave at
least 10 minutes before checking the level with a
dipstick.
Page 34 of 652
10A-28
ENGINE AND CYLINDER BLOCK ASSEMBLY
Engine oil: Draining - Refilling
K9K
10A
III - OIL SERVICE
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the engine oil filler cap (1) ,
-the dipstick (2) ,
-the engine undertray bolts,
-the engine undertray.
aPlace the oil recovery tray under the engine.aRemove the drain plug (3) from the engine oil sump
using the (Mot. 1018) or a oil change wrench.
aLet the engine oil flow out.
aRemove the drain plug seal.
aRefit the new seal to the drain plug.
aTorque tighten the drain plug (20 N.m) using a oil
change wrench and a oil change end piece with
an 8 mm square drive.
aWipe the oil drips around the drain plug using a
cloth.
aRemove the oil recovery tray.
aRefit the engine undertray.
IV - FILLING
aPosition the vehicle back on the ground.
aFill the engine with oil, observing the correct quantity
of oil as recommended by the manufacturer.
aWait at least 10 minutes.
aCheck the oil level using the dipstick.
aTop up the engine oil level if necessary.
aRefit:
-the engine oil filler cap,
-the dipstick.
120041
120042