headlights RENAULT TWINGO 2009 2.G Panelwork Workshop Manual

42A-3
FRONT UPPER STRUCTURE
Front wing: Removal - Refitting
42A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the halogen headlight (see Halogen headlight:
Removal - Refitting) (MR 411, 80B, Headlights).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the trim (1) ,
-the indicator (2) ,
-the windscreen trim piece.
aDisconnect the indicator.
aRemove:
-the bolts,
-the front wing.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIn addition, order the wing upper reinforcement and
mounting angle bracket.II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front wing,
-the bolts.
aConnect the indicator.
aRefit:
-the windscreen trim piece,
-the indicator (2) ,
-the trim (1) .
III - FINAL OPERATION.
aRefit:
-the halogen headlight (see Halogen headlight:
Removal - Refitting) (MR 411, 80B, Headlights),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection).
121198

42A-7
FRONT UPPER STRUCTURE
Front wing upper mounting support: Removal - Refitting42A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the halogen headlight (see Halogen headlight:
Removal - Refitting) (MR 411, 80B, Headlights),
-the front wing (see 42A, Front upper structure,
Front wing: Removal - Refitting, page 42A-3) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the bolts (1) ,
-the front wing upper mounting support ,
III - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front wing upper mounting support,
-the bolts (1) .
IV - FINAL OPERATION.
aRefit:
-the front wing (see 42A, Front upper structure,
Front wing: Removal - Refitting, page 42A-3) ,
-the halogen headlight (see Halogen headlight:
Removal - Refitting) (MR 411, 80B, Headlights),-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection).
121237

42A-9
FRONT UPPER STRUCTURE
Front end panel: Removal - Refitting
42A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the front bumper ( (see Front bumper: Removal -
Refitting) ),
-the headlights ( (see Halogen headlight: Remo-
val - Refitting) ),
-the bonnet catch ( (see Bonnet lock: Removal -
Refitting) ).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the wiring harness.
aRemove the bonnet opening cable.
aRemove the bolt (1) from the coolant bottle.
aUnclip the coolant bottle.
aRemove:
-the bolt (2) from the cooling radiator deflector,
-the bolts (3) from the cooling radiator support,
-the bolts (4) .
aUndo:
-the nut (5) ,
-the bolts (6) .
aRemove the front end panel.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front end panel,
121037
Note:
The bolts (4) and (6) can be accessed between
the front end lower cross member and the coo-
ling radiator.
Note:
The front end panel is made up of the front upper
cross member and the headlight carrier panels.

42A-10
FRONT UPPER STRUCTURE
Front end panel: Removal - Refitting
42A
-the bolts (4) ,
-the bolts (3) on the cooling radiator support,
-the bolt (2) on the cooling radiator deflector.
aTighten:
-The bolts (6) ,
-the nut (5) .
aClip on the coolant bottle.
aRefit the bolt (1) on the coolant bottle.
aPosition the bonnet opening release cable.
aClip on the wiring harness.
II - FINAL OPERATION.
aRefit:
-the bonnet catch ( (see Bonnet lock: Removal -
Refitting) ),
-the headlights ( (see Halogen headlight: Remo-
val - Refitting) ),
-the front bumper ( (see Front bumper: Removal -
Refitting) ).

42A-11
FRONT UPPER STRUCTURE
Headlight carrier panel: Removal - Refitting
42A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the halogen headlight (see Halogen headlight:
Removal - Refitting) (MR 411, 80B, Headlights),
-the bonnet catch (see Bonnet lock: Removal -
Refitting) (MR 412, 52A, Non-side opening ele-
ment mechanisms),
-the front upper cross member (see 42A, Front up-
per structure, Front upper cross member: Re-
moval - Refitting, page 42A-13) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aLoosen nut (2) .
aRemove:
-the bolts (1) ,
-the headlight carrier panel.
REFITTING
I - REFITTING PREPARATIONS OPERATION
a
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the headlight carrier panel,
-the bolts (1) .
aTighten the nut (2) .
III - FINAL OPERATION.
aRefit:
-the front upper cross member (see 42A, Front up-
per structure, Front upper cross member: Re-
moval - Refitting, page 42A-13) ,
-the bonnet catch (see Bonnet lock: Removal -
Refitting) (MR 412, 52A, Non-side opening ele-
ment mechanisms),
-the halogen headlight (see Halogen headlight:
Removal - Refitting) (MR 411, 80B, Headlights),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection).
121251
WARNING
For any adjustment or removal - refitting proce-
dure where it is necessar y to separate a bolted
connection, reapply the mating and sealing anti-
corrosion protection to the bolts using filler mas-
tic in a pre-formed bead.

42A-13
FRONT UPPER STRUCTURE
Front upper cross member: Removal - Refitting
42A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the front bumper ( (see Front bumper: Removal -
Refitting) ),
-the headlights ( (see Halogen headlight: Remo-
val - Refitting) ),
-the bonnet catch ( (see Bonnet lock: Removal -
Refitting) ).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the wiring harness.
aRemove the bonnet opening cable.
aRemove the bolt (1) from the coolant bottle.
aUnclip the coolant bottle.
aRemove:
-the bolt (2) from the cooling radiator deflector,
-the front upper cross member bolts (3) .
aUndo the bolts (4) .
aRemove the front upper cross member.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front upper cross member,
-the bolts (3) ,
-the bolt (2) on the cooling radiator deflector.
aTighten the bolts (4) .
aClip on the coolant bottle.
aRefit the bolt (1) on the coolant bottle.
aPosition the bonnet opening release cable.
aClip on the wiring harness.
II - FINAL OPERATION.
aRefit:
-the bonnet catch ( (see Bonnet lock: Removal -
Refitting) ),
-the headlights ( (see Halogen headlight: Remo-
val - Refitting) ),
-the front bumper ( (see Front bumper: Removal -
Refitting) ).
121036
Note:
The bolts (4) can be accessed between the front
end lower cross member and the cooling radia-
tor.

48A-1
NON-SIDE OPENING ELEMENTS
Bonnet: Removal - Refitting
48A
I - REMOVAL BY MEANS OF THE BONNET BOLTS
1 - REMOVAL PREPARATION OPERATION
aDisconnect the pipe (1) .
aUnclip the pipe at (2) .
2 - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the bolts (3) ,
-the bonnet.II - REFITTING BY MEANS OF THE BONNET BOLTS
1 - OPERATION FOR REFITTING PART
CONCERNED
aRefit:
-the bonnet,
-the bolts (3) .
aAdjust the opening clearances and flush fitting (see
48A, Non-side opening elements, Bonnet: Ad-
justment, page 48A-4) .
2 - FINAL OPERATION
aClip on the pipe at (2) .
aConnect the pipe at (1) .
III - REMOVAL BY MEANS OF THE BONNET HINGE
BOLTS
1 - REMOVAL PREPARATION OPERATION
aRemove:
-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the halogen headlights (see Halogen headlight:
Removal - Refitting) (MR 411, 80B, Headlights),
-the front wing (see 42A, Front upper structure,
Front wing: Removal - Refitting, page 42A-3) ,
aDisconnect the pipe at (1) .
aUnclip the pipe at (2) .
112036
121519

48A-2
NON-SIDE OPENING ELEMENTS
Bonnet: Removal - Refitting
48A
2 - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the bolts (4) ,
-the bonnet.
IV - REFITTING BY MEANS OF THE BONNET
HINGE BOLTS
1 - OPERATION FOR REFITTING PART
CONCERNED
aRefit:
-the bonnet,
-the bolts (4) .
aAdjust the opening clearances and flush fitting (see
48A, Non-side opening elements, Bonnet: Remo-
val - Refitting, page 48A-1) .
2 - FINAL OPERATION
aClip on the pipe at (2) .
aConnect the pipe at (1) .
aRefit:
-the front wing (see 42A, Front upper structure,
Front wing: Removal - Refitting, page 42A-3) ,
-the halogen headlights (see Halogen headlight:
Removal - Refitting) (MR 411, 80B, Headlights),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),-the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection).
121519