check engine RENAULT TWINGO 2009 2.G Sequential Transmission Owner's Guide

21B-58
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF150
PRESENT
OR
STOREDINSTRUMENT PANEL MULTIPLEX CONNECTION
1.DEF : No signal
NOTESPriorities when dealing with a number of faults:
If fault DF062 Multiplex line fault is present or stored, deal with it first.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after the computer fault memory has been cleared, the
ignition has been switched off and on again and the engine has been started.
Use the Wiring Diagrams Technical Note for New TWINGO.
Check the connection and condition of the connectors of components 120, 119 and 247.
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Run a multiplex network test (see 88B, Multiplex).
If the multiplex network is correct, perform a fault finding of the instrument panel (see 83A, Instrument panel).
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF150

21B-59
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF166
PRESENT
OR
STOREDPRESSURE SENSOR CIRCUIT
CO.0 : Open circuit or short circuit to earth
CC.1 : Short circuit to + 12 V
1.DEF : Signal incoherence
NOTESSpecial note:
–Fault warning light comes on.
Use the Wiring Diagrams Technical Note for New TWINGO.
CO.0/ CC.1
NOTESNone
Check the condition and position of the 30 A fuse for the pump in the engine compartment.
Repair if necessary.
Check the connection and condition of the connectors of components 119 and 1059 and the 24 track
intermediate connector located on the hydraulic unit.
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the continuity and insulation to earth and + 12 V on the following connections:
●Connection code 5HN,
●Connection code 5HX,
●Connection code 5AD,
between components 119 and 1059.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the oil pressure sensor on the Sequential gearbox (see MR 411, Sequential
gearbox, solenoid valve unit pressure sensor, Removal refitting).
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF166

21B-60
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF166
CONTINUED
1.DEF
NOTESNone
Check the level of oil in the discharged accumulator, refer to the interpretation of command AC081 Discharge
pressure accumulator.
Check the condition and position of the 30 A fuse for the pump in the engine compartment.
Use command AC012 “Hydraulic pump relay” with the diagnostic tool and check that the pump assembly is
working. If the pump is not working, perform the necessary repairs.
If the fault is still present, replace the oil pressure sensor (see MR 411, Sequential gearbox, solenoid valve unit
pressure sensor, Removal refitting).
Switch off the ignition.
Switch on the ignition again and carry out a new check using the diagnostic tool.
Replace the pump assembly if the fault reappears (see MR 411, Sequential gearbox, pump assembly,
Removal refitting).
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.

21B-63
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF181
PRESENT
OR
STOREDGEAR SELECTION IMPOSSIBLE
1.DEF : Impossible to select gear
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after an engine start attempt and an attempt to engage a
gear.
Special note:
–Fault warning light comes on.
–Neutral engaged immediately.
Check that there are no engagement or selection sensor faults.
If faults associated with these components are present, deal with these first.
Check that the selection control lever is correctly clipped to the hydraulic unit (see MR 411, 21B, Sequential
gearbox).
Carry out the necessary repairs.
Check that there is no water in the sequential gearbox oil.
Repair if necessary.
Clear the computer fault memory using command RZ001 "Stored fault(s)".
Carry out the programming procedure for the "Hydraulic unit - gearbox kit (without
clutch) or Clutch or gearbox + Clutch" (see "Replacement of components").
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF181

21B-64
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF185
PRESENT
OR
STOREDNO ABS/ESP MULTIPLEX SIGNAL
1.DEF : No signal
NOTESPriorities when dealing with a number of faults:
If fault DF062 Multiplex line fault is present or stored, deal with it first.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after the computer fault memory has been cleared, the
ignition has been switched off and on again and the engine has been started.
Use the Wiring Diagrams Technical Note for New TWINGO.
Perform a multiplex network test (see 88B, Multiplex).
Check the connection and condition of the connectors of components 120, 119 and 1094.
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
If the fault is still present, run fault finding on the ABS/ESP system (see 38C, Anti-lock braking system).
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF185

21B-65
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF187
PRESENT
OR
STOREDPROGRAMMING
1.DEF : Programming not carried out or inconsistent
2.DEF : Values outside the limits
3.DEF : Configuration/Initialisation
NOTESSpecial note:
–Fault warning light comes on.
–Impossible to start the engine.
Program the gears with command VP008 Program selection/engagement ranges.
Check that the solenoid valves are operating correctly using commands AC015 Engagement solenoid valves
and AC016 Selection solenoid valves.
Check the correct positioning of the actuators.
Repair if necessary (see MR 411, 21B, Sequential gearbox, Actuator module: Removal - Refitting).
If the fault is still present, apply the interpretation of faults DF072 Engagement solenoid valve 1 circuit, DF073
Engagement solenoid valve 2 circuit, DF074 Selection solenoid valve 1 circuit and DF075 Selection
solenoid valve 2 circuit.
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF187

21B-66
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF188
PRESENT
OR
STOREDSYSTEM OPERATION
NOTESPriorities when dealing with a number of faults:
Apply the interpretation of other faults first.
Special note:
–warning light comes on,
–neutral engaged immediately,
–engine stops immediately.
This fault appears following an electronic and mechanical inconsistency on the sequential system.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF188

21B-67
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF232
DF233
DF234
PRESENT
OR
STOREDCOMPUTER
1.DEF : Internal electronic fault
NOTESSpecial note:
–fault warning light comes on.
Use the Wiring Diagrams Technical Note for New TWINGO.
Check the condition and position of the sequential gearbox fuses in the engine compartment and in the
passenger compartment.
Check the connection and condition of the 52-track connector of component 119.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for + AVC on connection BP39 and for + after ignition feed on connection AP4 on the 52-track connector
of component 119.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connection:
●Connection code N of earths MC - 12B and MC - 12A.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
Clear the computer fault memory using command RZ001 "Stored fault(s)".
Switch off the ignition.
Switch on the ignition again and carry out a new check using the diagnostic tool.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF232 / BVRJH1_V04_DF233 / BVRJH1_V04_DF234

21B-68
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF251
PRESENT
OR
STOREDGEARBOX INPUT SPEED
1.DEF : Signal incoherence
2.DEF : Signal Absent
NOTESPriorities when dealing with a number of faults:
If fault DF254 Clutch temperature is present or stored, deal with it first.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after a road test.
Special note:
The fault can only be cleared from the memory using the diagnostic tool after a
road test where the vehicle speed signal is detected by the computer.
If fault DF254 Clutch temperature is present, the buzzer may sound.
Use the Wiring Diagrams Technical Note for New TWINGO.
Check the connection and condition of the connectors of components 119 and 1060.
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check that the sensor is correctly fitted on the sequential gearbox.
Engine running at idle speed and vehicle stopped, check the gearbox input engine speed sensor and the engine
speed sensor are operating correctly:
●PR006 Engine speed,
●PR014 "Gearbox input speed".
Check the continuity and insulation of the following connections:
●Connection code 5DA,
●Connection code 5DB,
between components 1060 and 119.
If the connections are faulty, check the connection and condition of intermediate connector R235 located on the
hydraulic unit.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, W iring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the gearbox input speed sensor resistance between connections 5DA and 5DB of the sensor are
equal to 470 Ω ± 94 Ω.
If the fault is still present, replace the sensor (see MR 411, 21B, Sequential gearbox, sequential gearbox
engine speed sensor: Removal - Refitting).
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF251

21B-70
MR-413-X44-21B000$472.mif
V2
SEQUENTIAL GEARBOX
Fault finding - Interpretation of faults
Vdiag No: 04
21B
DF254
PRESENT
OR
STOREDCLUTCH TEMPERATURE
1.DEF : Clutch overheating
NOTESPriorities when dealing with a number of faults:
Deal with other faults declared present first.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the clutch is used under severe conditions
(prolonged holding on a hill).
Special note:
–Instrument panel displays: “Sequential gearbox overheating”
–Fault warning light comes on.
–An engine speed wire fault or incorrect multiplex line value (speed equals 0) may
increase the occurrence of this fault.
Clear the stored fault and check that the clutch is not slipping by performing a road test, pulling away with a low
load then up or down an incline.
If the clutch slips, proceed in the following way:
–Pull away several times with low load and check parameter PR096 Clutch progressivity.
–If the fault is still present, replace the clutch.
AFTER REPAIRDeal with any faults detected by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
BVRJH1_V04_DF254