ECU RENAULT TWINGO 2012 2.G Owner's Manual

3.24
ENG_UD4077_2
Toit ouvrant à commande électrique (X44 - Renault)
ENG_NU_952-4_X44_Renault_3
Special features
For your safety your vehicle is fitted
with an anti-pinch facility. When a
window encounters resistance whilst
closing (e.g. someone’s fingers, an ani-
mal’s paw or the branch of a tree, etc.),
it stops and lowers by several centime-
tres.
ElECTRIC SuNRooF (continued)
Sunroof closing operating
fault
In this case, check that there is no ob-
struction, then turn button 2 to posi -
tion 0 , then press button 3 , until the
sunroof closes completely.
Important: during this operation, the
sunroof anti-pinch function is deac-
tivated.
Contact your RENAULT Dealer as
soon as possible.
Precautions during use
– Do not open the sunroof immedi -
ately after it has rained or immedi -
ately after washing the vehicle.
– check that the sunroof is properly
closed before leaving your vehicle;
– clean the seal every three months
using products recommended by our
Technical Department;
– vehicle with roof bars:
Generally, it is not advisable to oper-
ate the sunroof.
Before using the sunroof, check the
objects and/or accessories (bike
racks, roof boxes, etc.) attached to
the roof bars: they should be prop -
erly arranged and secured and
should not interfere with the opera -
tion of the sunroof.
Consult your RENAULT Dealer for
details of possible adaptations.
0
3
2

transporting objectsin the luggage compartment ........... (up to the end of the DU)
towing rings ........................................................... (current page)
3.37
ENG_UD24509_4
Transport d objets dans le coffre (X44 - Renault)
ENG_NU_952-4_X44_Renault_3
Transporting objects in the boot
TRANSPoRTINg oBJECTS IN ThE luggAgE CoMPARTMENT
Always place the objects to be trans -
ported so that their largest side rests
against the back of the rear bench
seat, for normal loads (Example A), or
against the back of the front seats when
the rear bench seatbacks are folded
down, as with maximum loads (exam -
ple B).
Always position the heavi -
est items directly on the
floor. Use the lashing points
on the floor of the luggage
compartment, if these are fitted to
the vehicle. The luggage should be
loaded in such a way that no items
will be thrown forward and strike the
occupants if the driver has to brake
suddenly. Fasten the rear seat belts,
even if the seats are not occupied.
locations for anchorage
points
(depending on the vehicle)
These are for securing items trans -
p o r t e d i n th e l u g g a g e c o m p a r t -
ment (refer to the information on
“Transporting objects in the luggage
compartment”).
AB

roof bars ............................................... (up to the end of the DU)
roof rack roof bars .......................................... (up to the end of the DU)
3.39
ENG_UD24696_3
Barres de toit (X44 - Renault)
ENG_NU_952-4_X44_Renault_3
Roof bars
RooF BARS
Accessing the mounting
points
Open the doors. Behind seal 2 are
blanking bolts 1 which protect the
mounting bolt locations.
When fitting roof bars, at the front of the
vehicle, replace the blanking bolts with
the mounting bolts supplied with the
roof bars. Behind seal 3 , position the
roof bars in the reinforced area 4 pro -
vided.
Never remove blanking
bolts 1 without plugging the
holes afterwards.
Once they are secured on
to the vehicle, the mount -
ing bolts should never be
removed (risk of damaging
the vehicle).
If original roof bars, approved by our
Technical Department, are supplied
with screws, only use these screws
for attaching the roof bars to the ve-
hicle.
13
For information on the range of
equipment adapted to your vehi -
cle, we advise you to consult an ap-
proved Dealer.
Refer to the fitting instructions for in-
formation on how to fit roof bars and
conditions of use.
Please keep these instructions with
the rest of the vehicle documenta -
tion.
Maximum permissible load on
roof rack: refer to the information
on “Weights” in Section 6.
24

oil change .............................................................. (current page)
filter oil filter ............................................................. (current page)
4.6
ENG_UD24736_5
Niveau huile moteur : appoint/remplissage (X44 - Renault)
ENG_NU_952-4_X44_Renault_4
Filling: take care when
topping up the oil that
no oil drips onto engine
components - risk of fire.
Remember to refit the cap securely
as there is a risk of fire if oil splashes
onto hot engine components.
Never run the engine in an
enclosed space as exhaust
gases are poisonous.
Consult your approved Dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in the park position.
Risk of injury.
Oil change
S e r v i c e i n t e r v a l : r e f e r t o t h e
Maintenance Service Booklet for your
vehicle.
Average capacities for oil change (in-
cluding oil filter for information).
1.2 16V engine: 4.35 litres
1.5 dCi engine: 4.4 litres
Engine oil grade
Refer to the Maintenance Service
Booklet for your vehicle.
Engine oil change : if you
are changing the oil when
the engine is hot, be careful
not to scald yourself if the
oil overflows.
The engine may be hot
when carrying out opera -
tions in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
ENGINE OIL LEVEL: topping up/filling (2/2)ENGINE OIL ChANGE
Engine oil change

4.14
ENG_UD26811_2
Entretien de la carrosserie (peinture mate) (X44 - X77 - J77 - X85 - \
B90 - X61 - TEST - X77 ph2 - X95 - B95 - D95 - K95 - J95 - R95 - L90 Ph2 - F90 Ph2 - R90\
Ph2 - X62
ENG_NU_952-4_X44_Renault_4
Respect local regulations about wash -
ing vehicles (e.g. do not wash your ve-
hicle on a public highway).
Observe the vehicle stopping distances
when driving on gravelled surfaces to
prevent paint damage.
Repair, or have repaired quickly, areas
where the paint has been damaged, to
prevent corrosion spreading.
Remember to visit the body shop pe -
riodically in order to maintain your
anti-corrosion warranty. Refer to the
Maintenance Document.
If it is necessary to clean mechani -
cal components, hinges, etc., spray
them with products approved by our
Technical Department to protect them
after they have been cleaned.
BODyWORk MAINTENANCE (2/2)
We have selected special products
to care for your vehicle and you can
obtain these from the manufactur -
er’s accessory outlets.
Using a roller type car wash
Return the windscreen wiper stalk to
the Park position (refer to the informa-
tion on the “Windscreen washer, wiper”
in Section 1). Check the mounting of
external accessories, additional lights
and mirrors, and ensure that the wiper
blades are secured with adhesive tape.
Remove the radio aerial mast if your
vehicle is fitted with this equipment.
Remember to remove the tape and refit
the antenna after washing.
Cleaning the headlights
As the headlights are made of plastic
“glass”, use a soft cloth or cotton wool
to clean them. If this does not clean
them properly, moisten the cloth with
soapy water, then wipe clean with a soft
damp cloth or cotton wool.
Finally, carefully dry off with a soft dry
cloth.
Cleaning products containing alco -
hol must not be used.
Vehicles with a matte paint
finish
This type of paint requires certain pre-
cautions.
Do not do the following
– use wax-based products (polishing);
– rub hard;
– wash the vehicle in a roller-type car
wash;
– wash the vehicle using a high-pres-
sure device;
– attach stickers to the paintwork (risk
of leaving marks).
y ou should do the following
Wash the vehicle by hand using plenty
of water, using a soft cloth or a gentle
sponge.

4.16
ENG_UD22508_5
Entretien des garnitures intérieures (X44 - Renault)
ENG_NU_952-4_X44_Renault_4
INTERIOR TRIM MAINTENANCE (2/2)
Removing/refitting factory
fitted removable equipment
in the vehicle
If you need to remove equipment to
clean the passenger compartment (e.g.
mats), always make you refit it properly
and on the correct side (driver’s side
mats must be fitted on the driver’s side,
etc.), using retaining components sup-
plied with the equipment (e.g. the driv-
er’s side mat must always be secured
using prefitted retaining devices).
In all cases, with the vehicle stationary,
ensure that nothing can hinder driving
(obstacle underneath the pedals, heel
trapped by the mat, etc.).
What you should not do
You are strongly advised not to place
items such as air fresheners, perfume
etc. near the air vents as these could
damage the dashboard fittings.
You are strongly recom -
mended not to use high -
pressure or spray cleaning
equipment inside the pas -
senger compartment: this equip -
ment could impair the correct func-
tioning of the electrical or electronic
components in the vehicle, or have
other detrimental effects.

JauneNoirNoir texte
5.5
ENG_UD28665_3
Kit de gonflage des pneumatiques (X77 - X85 - B85 - C85 - S85 - X77 ph2\
- K85 - X95 - E95 - X67 - X92 - X10 - X98 - X52 - Renault)
ENG_NU_952-4_X44_Renault_5
tYre PreSSure KIt (3/3)
Once the tyre is correctly inflated,
remove the kit: slowly unscrew the in -
flation adapter 1 to prevent any repair
product from escaping and store the
container in plastic packaging to pre -
vent the product from escaping.
– Affix the driving recommendation
label to the dashboard where it can
easily be seen by the driver;
– Put the kit away.
– At the end of this initial inflation op-
eration, air will still escape from the
tyre. You must drive a short distance
in order to seal the hole.
– Start immediately and drive at be -
tween 12 and 40 mph (20 and
60 km/h) in order to distribute the
product evenly in the tyre and, after
driving for 2 miles (3 km), stop and
check the pressure.
– If the pressure is greater than 1.3 bar
but less than the recommended
pressure (refer to the label affixed to
the edge of the driver’s door), read-
just it. Otherwise, please contact an
authorised dealer: the tyre cannot be
repaired.Precautions when using the
kit
The kit should not be operated for more
than 15 consecutive minutes.
Nothing should be placed
around the driver ’s feet
as such objects may slide
under the pedals during
sudden braking manoeuvres and
obstruct their use.
1
Please be aware that a
poorly tightened or miss -
ing valve cap can make the
tyres less airtight and may
lead to pressure loss.
Always use valve caps identical to
those fitted originally and tighten
them fully.
Following repair with the kit,
do not travel further than
120 miles (200 km). In addi -
tion, reduce your speed and
under no circumstances exceed
48 mph (80 km/h). The sticker,
which you must affix in a prominent
position on the dashboard, reminds
you of this.
Depending on the country or local
legislation, a tyre repaired with the
inflation kit may need to be replaced.

hubcap tool ............................................................ (current page)
wheelbrace ............................................................ (current page)
emergency spare wheel ........................................ (current page)
towing hitch ............................................................ (current page)
5.6
ENG_UD24733_5
Bloc outils (X44 - Renault)
ENG_NU_952-4_X44_Renault_5
Tool kit
Tool kit 3 is located in the emergency
spare wheel. It consists of a set of tools
for various operations on the vehicle: a
jack and wheelbrace, towing hitch, etc.,
and a space for a spare bulb box.
The tools included in the tool kit depend
on the vehicle.
Storage compartments 1
This is for storing a box of bulbs.
Storage compartments 2
This is for storing four wheel bolts.
Wheelbrace 4
This is used to tighten or release the
wheel bolts.
t owing hitch 7
Refer to the information on “Towing” in
Section 5.
Hubcap tool 5 or 6
This tool is used to remove the wheel
trims.
Jack 3
Remove jack 3.
When replacing the jack, fold it cor -
rectly and position the wheelbrace cor-
rectly before replacing it in its position.
Do not leave the tools un -
secured inside the vehicle
as they may come loose
under braking. After use,
check that all the tools are correctly
clipped into the tool kit, then position
it correctly in its housing: there is a
risk of injury.
The jack is designed for wheel
changing purposes only. It should
never be used for repairs or gaining
access to the underneath of the ve-
hicle.
t OOL KIt
1
3
2
3
4
5
6
7

operating faults ..................................... (up to the end of the DU)
faults operating faults ............................... (up to the end of the DU)
5.35
ENG_UD18961_2
Anomalies de fonctionnement (X44 - Renault)
ENG_NU_952-4_X44_Renault_5
Operating faults
OPerA tIng FAuL tS (1/5)
the following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact
a renAuLt Dealer as soon as possible.
the starter is activated POSSIBLe cAuSeSWHAt tO DO
The indicator lights fail to light up and
the starter does not turn. Battery terminals disconnected,
oxidised or incorrectly secured.Retighten, reconnect or clean them if they
are oxidised.
Battery discharged or unservice -
able. Connect another battery to the faulty bat
-
tery. Refer to the paragraph “Battery: trou-
bleshooting” in section 5 or replace the bat-
tery if necessary.
Do not push the vehicle if the steering
column is locked.
The engine will not start. Starting conditions are not fulfilled.Refer to the information on “Starting/stop -
ping the engine” in Section 2.
The steering column remains locked. Steering wheel locked.To unlock, move the key and the steering
wheel gently (refer to the information on the
“Ignition switch” in Section 2).