ignition RENAULT TWINGO RS 2009 2.G Chasiss ABS Owner's Manual

38C-60
MR-413-X44-38C000$846_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with command modes
MK70 ABS
Vdiag No: 04
38C
AC016
PUMP MOTOR TEST
NOTESConditions of use of the command.
Ignition on, engine stopped and vehicle speed zero.
Before using the command, check that the battery is fully charged.
This command is used to test the pump motor control circuit.
Select command AC016 Pump Motor Test.
The motor must run for 5 seconds.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_AC016

38C-61
MR-413-X44-38C000$846_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with command modes
MK70 ABS
Vdiag No: 04
38C
AC153
AC154
AC155
AC156BLEED FRONT LEFT-HAND WHEEL
BLEED FRONT RIGHT-HAND WHEEL
BLEED REAR LEFT-HAND WHEEL
BLEED REAR RIGHT-HAND WHEEL
NOTESConditions of use of the command.
Ignition on, engine stopped and vehicle speed zero.
Before using the commands, check that the battery is fully charged.
These 4 commands should only be used if you observe lengthening of the brake pedal travel during a road test
with ABS regulation (the system should have been bled in advance using the conventional procedure).
See ALP8.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_AC153 / ABS_V04_AC154
ABS_V04_AC155 / ABS_V04_AC156

38C-62
MR-413-X44-38C000$846_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with command modes
MK70 ABS
Vdiag No: 04
38C
AC195
VEHICLE SPEED SIGNAL
NOTESConditions of use of the command.
Ignition on, engine stopped and vehicle speed zero.
Before using the command, check that the battery is fully charged.
This command is used to generate a speed other than 0 mph at the computer's vehicle speed wire output
(connection 47F) for users of that signal (radio, sunroof).
This command has no visible effect on the dashboard speedometer needle.
–Radio: Turn on the radio and make sure that the Adjust volume as a function of speed function is active.
Run command AC195. During the command, you should notice the volume of the sound increase and then
decrease. (See 86A, radio).
–Sunroof: This command has no visible effect on the sunroof. This command changes the activation threshold
of the anti-pinch system (the energy required to close the sunroof varies with vehicle speed due to aerodynamic
constraints). (See 87D ELECTRIC WINDOWS - SUNROOF).
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_AC195

38C-63
MR-413-X44-38C000$846_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with command modes
MK70 ABS
Vdiag No: 04
38C
AC196
HAZARD WARNING LIGHT ACTIVATION REQUEST
NOTESConditions of use of the command.
Ignition on, engine stopped and vehicle speed zero.
Before using the command, check that the battery is fully charged.
This command sends a hazard warning light activation request to the UCH (Passenger compartment connection
unit) to test their operation in the event of emergency braking (depending on UCH, Passenger Compartment
Connection Unit configuration).
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_AC196

38C-66
MR-413-X44-38C000$940_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Fault Finding Chart
MK70 ABS
Vdiag No: 04
38C
ALP 1
CONTINUED
Ensure that the supply to the diagnostic socket is correct:
Check the condition and position of the F12 5 A fuse in the Passenger compartment fuse box.
Consult section 81C, Fuses.
Connector of component 645 of connection BP19 disconnected:
–Check for + after ignition feed on connection BP19 of component 225.
If the + after ignition feed is not present on connection BP 19, check component 1016.
–Check connections NAM and MAM of component 225.
If the connection is faulty (see Technical Note 6015A, Repairing electrical wiring, wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If dialogue has still not been established after these checks, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.

38C-72
MR-413-X44-38C000$940_eng.mif
V1
ANTI-LOCK BRAKING SYSTEM
Fault finding - Fault Finding Chart
MK70 ABS
Vdiag No: 04
38C
ALP 7Unexpected ABS operation when using special equipment
(car phone, CB, etc.)
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Check that the equipment which is causing the fault is approved.
Check that this equipment has been correctly installed without modification to the original wiring, in particular, that
of the ABS (connections to earth and + after ignition/+ before ignition of the ABS are not permitted).
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS_V04_ALP7