sunroof RENAULT TWINGO RS 2009 2.G Electrical Equipment - Access Safety Workshop Manual

82D-7
MR-413-X44-82D000$200_eng.mif
V1
82D
ACCESS/SAFETY
Fault finding - List and location of components
1UCH
2Passenger Compartment Fuse and Relay Box
3One touch window/anti-pinch module
4Transponder ring
5Rain/light sensor & interior temperature sensor
6Sunroof/anti-pinch
7Tailgate lock
8Door lockENGINE HARNESS
FRONT ENGINE WIRING & ADDITIONAL HEADLIGHTS
DOOR WIRING
CEILING WIRING
PASSENGER COMPARTMENT WIRING
REAR BUMPER WIRING
TAILGATE WIRING
MR-413-X44-82D000$200_eng.mif

82D-20
MR-413-X44-82D000$600_eng.mif
V1
82D
ACCESS/SAFETY
Fault finding - Configurations and programming
Replacing the computer
After the injection computer or UCH has been replaced, program the immobiliser code into the new computer
(see 87B, Passenger compartment connection unit, Configuration and programming).
Access/Safety function configurations in the UCH
–Individual configuration available using the diagnostic tool, and the associated configuration should be read
Procedure to follow for modifying these configurations
–establish dialogue with the computer corresponding to the desired configuration.
–select the "repair mode" menu,
–select the "enter configuration" menu,
–select the line corresponding to the configuration to be modified,
–in the drop-down menu, select the line corresponding to the vehicle equipment level or to the customer selection
and click on "confirm",
–In the "Read configuration" menu, check that the configuration has been completed.
SR.*: Sunroof
*RF: radio frequencyEquipment required
Diagnostic toolClip
ConfigurationConfiguration
readingName of configuration Option
CF009 LC003Deadlocking WITH/WITHOUT
-LC089Memory key function WITH/WITHOUT
CF108 LC040 "Renault Anti-Intruder Device"WITH/WITHOUT
CF009 LC003 "Deadlocking"WITH/WITHOUT
CF192 LC093 "Central door locking"WITH/WITHOUT
CF195 LC097 "Type of key" STANDARD/RF*
CF229 LC126 "Alarm"WITH/WITHOUT
CF031 - "Calibration"-
CF173 LC070 "One-touch window(s)/SR*"WITH/WITHOUT
Note:
If configuration LC089 "Memory key function" is WITH and if status ET407 "Memory key" is YES, the UCH
allows the vehicle information stored in the key to be used.
MR-413-X44-82D000$600_eng.mif

82D-21
MR-413-X44-82D000$700_eng.mif
V1
82D
ACCESS/SAFETY
Fault finding - Conformity check
SUB-FUNCTION: ACCESS
SR.*: Sunroof
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)1
TailgateET061:Open tailgate
requestPRESENT
ABSENTIn the event of a fault,
apply the
interpretation of
status ET061
(see 87B, UCH).
2ET463:Door(s) or
tailgateOPEN
CLOSEDIn the event of a fault,
apply the
interpretation of
status ET463
(see 87B, UCH).
3
Locking/unlocking
buttonET186:Short press on
door closing
buttonSignal can be
interpreted if the
ignition is
switched off (key
removed from the
ignition switch).
ACTIVE
INACTIVEIn the event of a fault,
refer to the
interpretation of
status ET186
(see 87B, UCH).
4ET189:Long press on
door opening
buttonSignal can be
interpreted if the
ignition is
switched off (key
removed from the
ignition switch).
ACTIVE
INACTIVEIn the event of a fault,
refer to the
interpretation of
status ET189
(see 87B, UCH).
5Electric central
locking buttonET044:Central
Locking buttonPRESSED
RELEASEDIn the event of a fault,
refer to the
interpretation of
status ET044
(see 87B, UCH).
6One-touch window/
SR*ET087:One-touch
window/SR*
authorisationPRESENT
ABSENTIn the event of a fault,
apply the
interpretation of
status ET087
(see 87B, UCH).
MR-413-X44-82D000$700_eng.mif