check engine RENAULT TWINGO RS 2009 2.G Electrical Equipment - Access Safety Workshop Manual

82D-17
MR-413-X44-82D000$500_eng.mif
V1
ACCESS/SAFETY
Fault finding - Function82D
d) Automatic locking
Automatic relocking takes place 2 minutes after an unlocking which is not followed by the opening of a door or the
tailgate.
The RAID function locks the vehicle as soon as the speed signal is above approximately 3 mph (5 km/h).
A road test can be used to check whether the RAID function is active or inactive.
The RAID function can be activated or deactivated by pressing and holding the electric door locking switch for
approximately 5 s while the engine is running. Acknowledgement is indicated by a buzzer.
Lock motor operation and feed via the UCH can be checked using the following actuator commands:
–AC004 Central door locking
–AC005 Central door unlocking
–AC061 Unlocking the tailgate
–AC035 Deadlocking
Entry level vehicle access and safety. This function is also divided into another three
sub-functions:
–Access:
This feature is not controlled by the UCH and comprises the following components:
–2 side door mechanical locks.
–1 tailgate electric lock.
–1 tailgate locking switch (with lock barrel).
–1 tailgate switch
Note:
Entry level vehicles are equipped with this system and these vehicles do not have electric central door locking.
–Safety and starting:
Identical to top of the range vehicles.Note:
Unlocking can be performed by the UCH if the airbag computer has detected an impact or if it is faulty (not
recognised on the multiplex network, internal fault, etc.).
(See 88C, Airbag - Seat belt pretensioners).

82D-18
MR-413-X44-82D000$500_eng.mif
V1
ACCESS/SAFETY
Fault finding - Function82D
2. Protection
PROCESS FOR REMOVING VEHICLE PROTECTION
When the + after ignition is switched on, the key and the UCH communicate via the transponder aerial and the key
code is sent to the UCH.
By means of an exchange of codes, the UCH checks that the key belongs to the vehicle.
When the key has been identified, the UCH and the injection identify each other by an exchange of codes via the
multiplex system.
If the UCH and the injection computer authenticate each other, the UCH authorises the engine to start and the
injection is unlocked.
The immobiliser statuses can be viewed using the following statuses:
–ET046 Immobiliser
–ET008 Blank UCH
–ET185 Key Code received
–ET181 Key allocated to vehicle
–ET045 RF signal received
–ET193 RF signal from a key allocated to the vehicle
–ET240 Key frequency (MHz)
–PR056 Number of keys allocated
–ET229 Injection immobiliser code
–ET250 Injection code
–ET239 Ignition switch position
Special cases
If the key code and the UCH code do not match, the system remains locked. The vehicle cannot be started.
Exchanges between protection function components
Note:
–The UCH authorises the operation of the starter.
–The injection system authorises the operation of the injectors.–key identifier request
–immobiliser code request
KeyUCH
Transponder ring
–key identifier signal
–immobiliser code signal
–UCH authentication request
–injection authorisation
UCHInjection
–UCH authentication signal
–starter supply authorisation

82D-21
MR-413-X44-82D000$700_eng.mif
V1
82D
ACCESS/SAFETY
Fault finding - Conformity check
SUB-FUNCTION: ACCESS
SR.*: Sunroof
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)1
TailgateET061:Open tailgate
requestPRESENT
ABSENTIn the event of a fault,
apply the
interpretation of
status ET061
(see 87B, UCH).
2ET463:Door(s) or
tailgateOPEN
CLOSEDIn the event of a fault,
apply the
interpretation of
status ET463
(see 87B, UCH).
3
Locking/unlocking
buttonET186:Short press on
door closing
buttonSignal can be
interpreted if the
ignition is
switched off (key
removed from the
ignition switch).
ACTIVE
INACTIVEIn the event of a fault,
refer to the
interpretation of
status ET186
(see 87B, UCH).
4ET189:Long press on
door opening
buttonSignal can be
interpreted if the
ignition is
switched off (key
removed from the
ignition switch).
ACTIVE
INACTIVEIn the event of a fault,
refer to the
interpretation of
status ET189
(see 87B, UCH).
5Electric central
locking buttonET044:Central
Locking buttonPRESSED
RELEASEDIn the event of a fault,
refer to the
interpretation of
status ET044
(see 87B, UCH).
6One-touch window/
SR*ET087:One-touch
window/SR*
authorisationPRESENT
ABSENTIn the event of a fault,
apply the
interpretation of
status ET087
(see 87B, UCH).
MR-413-X44-82D000$700_eng.mif

82D-22
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: ACCESS (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)7Locking
commandAC004:Central door
lockingThis command is
used to test whether
central door locking is
workingIn the event of a
fault, refer to the
procedure for
command AC004
(see 87B, UCH).
8Deadlocking
controlAC035:DeadlockingThis command is
used to test whether
the deadlocking is
working if the vehicle
is configured "WITH"
deadlocking.In the event of a
fault, refer to the
procedure for
command AC035
(see 87B,
Passenger
compartment
connection unit).
9AC005:Central door
unlockingThis command is
used to test whether
the 4 doors, tailgate
and fuel filler flap
unlocking function is
operating correctly.In the event of a
fault, refer to the
procedure for
command AC005
(see 87B,
Passenger
compartment
connection unit).
10Tailgate opening
controlAC061:Tailgate openingThis command is
used to test whether
the tailgate opening
motor is working.In the event of a
fault, refer to the
procedure for
command AC061
(see 87B,
Passenger
compartment
connection unit).

82D-23
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
UCH (see 87B,
Passenger
compartment
connection unit)1
Engine
immobiliserET046:Engine
immobiliserINACTIVE = Vehicle
unprotected, ready
to start.
ACTIVE = Vehicle
protected, starting
impossible.In the event of a
fault, refer to the
interpretation of
status ET046
(see 87B,
Passenger
compartment
connection unit).
2ET008:blank UCHYES = If the UCH
is blank.
NO = if the UCH has
been programmed
with an immobiliser
code.In the event of a
fault, refer to the
interpretation of
status ET008
(see 87B,
Passenger
compartment
connection unit).
3
KeyET185:Key code
receivedYES = If the UCH has
received the
immobiliser code
from the key.
NO = If the UCH does
not receive the
immobiliser code
from the key.In the event of a
fault, refer to the
interpretation of
status ET185
(see 87B,
Passenger
compartment
connection unit).
4ET181:Key allocated to
the vehicleYES = The key is
allocated to the
vehicle.
NO = The key is not
allocated to the
vehicle.In the event of a
fault, refer to the
interpretation of
status ET181
(see 87B,
Passenger
compartment
connection unit).

82D-24
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 1)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection unit)5
KeyET045:Radiofrequency
signal receivedYES = When the
UCH receives a
radiofrequency
signal.
NO = When the
UCH does not
receive a
Radiofrequency
signal.In the event of a fault,
refer to the
interpretation of
status ET045
(see 87B, Passenger
compartment
connection unit).
6ET193:Radiofrequency
signal from a key
allocated to the
vehiclePRESENT =
Reception of a
radiofrequency
signal from a key
allocated to the
vehicle.
ABSENT = No
reception of
frequency signal or
reception of
frequency signal
from a key not
allocated to the
vehicle.In the event of a fault,
refer to the
interpretation of
status ET193
(see 87B, Passenger
compartment
connection unit).
7ET240:Key frequency
(in MHz)433
NONEIf "NONE", check that
there is a
radiofrequency key by
trying with another key
(see 87B, Passenger
compartment
connection unit).
8PR056:Number of keys
allocatedX key(s)In the event of a fault,
refer to the
interpretation of
PR056 (see 87B,
Passenger
compartment
connection unit).

82D-25
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection unit)9
InjectionET229:Injection
immobiliser
codePROGRAMMED
NOT
PROGRAMMED
UNDETERMINEDIn the event of a fault, refer
to the interpretation of
status ET229 (see 87B,
Passenger compartment
connection unit).
10 ET250:InjectionNOT
PROTECTED
PROTECTEDIn the event of a fault, refer
to the interpretation of
status ET250
(see 17B, Petrol
injection, Conformity
check, Protection)
(see 13B, Diesel
injection, Conformity
check, Protection)
(see 87B, Passenger
compartment
connection unit).
11Starter actuatorET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition
feed.
+ START FEEDIn the event of a fault, refer
to the interpretation of
status ET239 (see 87B,
Passenger compartment
connection unit).

82D-26
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 3)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Diesel
Injection
(see 13B,
Diesel
Injection)1Computer + after
ignition feedET001:Computer +
after ignition
feedPRESENT
Indicates + after ignition
computer feed.
PRESENT/ABSENTIn the event of a fault,
use the interpretation
of faults DF047
"Computer feed
voltage" and DF015
"Main relay control
circuit ".
2Engine
immobiliserET003:Engine
immobiliser INACTIVE
- INACTIVE: The
injection computer has
recognised the
immobiliser code
transmitted by the UCH.
- ACTIVE: The injection
computer has not
recognised the
immobiliser code
transmitted by the UCH.If ACTIVE, use the
"help" for ET003 on
the tool.
3Code
programmedET006:Code
programmedYES
States whether the
immobiliser code has
been programmed by the
computer or not.
YES: Code programmed
NO: Code not
programmed into the
injection computerIf NO, test the
multiplex network.
4StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED,
carry out a complete
fault finding
procedure on the
preheating system.

82D-27
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: PROTECTION (CONTINUED 4)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
Petrol
Injection
(see 17B,
Petrol
Injection)1Computer +
after ignition
feedET001:Computer +
after ignition
feedPRESENT
Indicates + after
ignition computer feed.
PRESENT/ABSENTIn the event of a
fault, use the
interpretation of
faults DF047
"Computer feed
voltage" and
DF015 "Main relay
control circuit".
2Engine
immobiliserET003:Engine
immobiliser INACTIVE
- INACTIVE: The
injection computer has
recognised the
immobiliser code
transmitted by the UCH.
- ACTIVE: The injection
computer has not
recognised the
immobiliser code
transmitted by the UCH.If ACTIVE, use "the
help" for ET003 on
the tool.
3Code
programmedET341:Immobiliser
code
programmedYES
States whether the
immobiliser code has
been programmed by
the computer or not.
YES: Code programmed
NO: Code not
programmed into the
injection computerIn the event of a
fault, refer to the
interpretation of
status ET341
"Immobiliser code
programmed".
4StartingET076:StartingAUTHORISED
Indicates whether or not
starting has been
authorised by the
injection
AUTHORISED: injection
authorises starting.
PROHIBITED: Injection
does not authorise
startingIf PROHIBITED,
carry out a complete
fault finding
procedure on the
preheating system.

82D-28
MR-413-X44-82D000$700_eng.mif
V1
ACCESS/SAFETY
Fault finding - Conformity check82D
SUB-FUNCTION: STARTING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Computer Order FunctionParameter or Status
checked or ActionDisplay and
NotesFault finding
UCH (see 87B,
Passenger
compartment
connection
unit)1
EngineET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition
feed.
+ START FEEDIn the event of a fault, refer to the
interpretation of status ET239
(see 87B, Passenger
compartment
connection unit).
And (see 17B, Petrol Injection,
Conformity check, Protection)
(see 13B, Diesel Injection,
Conformity check,
Protection).
2ET142:Engine
operating phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, refer to the
interpretation of status ET142
(see 87B, Passenger
compartment
connection unit).
And (see 17B, Petrol Injection,
Conformity check, Protection)
(see 13B, Diesel Injection,
Conformity check,
Protection).
3PR025:Engine speed0 rpmIn the event of a fault, carry out a
fault finding on the multiplex
network (see 88B).
And (see 17B, Petrol Injection,
Conformity check, Protection)
(see 13B, Diesel Injection,
Conformity check,
Protection).