lights RENAULT TWINGO RS 2009 2.G Electrical Equipment - Airbags And Pretensioners Workshop Manual

88C-2
MR-413-X44-88C000$077.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
To run fault finding on the vehicle computers, switch on the ignition. Proceed as follows:
–turn the ignition key to APC,
–connect the diagnostic tool and perform the required operations.
To cut off the + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–turn the ignition key to OFF,
–verify that the forced + after ignition feed has been switched off by checking that the computer warning lights on
the control panel have gone out. Vehicle (s): New TWINGO
Function concerned: AIRBAGName of computer: TEMIC MRSZ
Vdiag No.: 04
Special tooling required
Multimeter
–Dummy module (Part no. Elé. 1835 yellow)
–Dummy module (Part no. Elé. 1837 - 2)
–Dummy module (Part no. Elé. 1837 - 5)
–Dummy module (Part no. Elé. 1837 - 6)
ABGMRSZ_V04_PRELI
MR-413-X44-88C000$077.mif
MRSZ AIRBAG
Vdiag: 04

88C-16
MR-413-X44-88C000$308.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Function
The MRSZ airbag computer takes control of all of the vehicle's restraint devices intended to ensure the protection of
the occupants (driver, front and rear passengers).
The MRSZ computer is designed to carry out the following functions:
●detection and confirmation of longitudinal impacts (front or rear) and/or side impacts,
●corresponding activation of the pyrotechnic restraint devices (e.g.: pretensioner, airbag),
●management of the different signals relating to the characteristics of the occupants (e.g.: presence detection),
●management of the function inhibiting the trigger lines and the passenger sensor,
●management and surveillance of the instrument panel "Airbag Fault" and "Airbag Off" warning lights via the
CAN network,
●activation of the "Crash output" signal via the CAN in the event of a crash,
●management of the fault finding signals (signals provided by the fault manager in response to fault finding
requests, whether this consists of internal faults or input/output fault finding).
Special notes:
–Frontal impacts:
This function is carried out using the MRSZ accelerometer. Accelerometers measure the violence of the impact. The
vehicle speed, the position of the passenger airbag locking switch and the accelerometer measurements determine
the strategy that the computer adopts to trigger the ignition modules. The front seat belt buckle pretensioners and
the front airbag may also be triggered or not depending on the input parameters.
–Side impacts:
This function is carried out by the MRSZ computer and the side impact sensors, if fitted.
The position of the passenger airbag locking switch and the accelerometer measurements determine the strategy
that the computer adopts to trigger the ignition modules. The front buckle pretensioners and the front chest-level
airbags and curtain airbags may also be triggered or not.
–Inhibition of passenger trigger lines:
This function is managed by the airbag computer, according to the position of the passenger airbag inhibition switch
and depending on the vehicle context.
The change in status of the inhibition switch must be done outside of after ignition feed. A change in status of the
switch is, however, authorised for 10 seconds after the after ignition feed for the vehicle is switched on.
If a change is status occurs outside of this 10 seconds, the computer will register a fault.
Inhibition programming:
–Trigger lines inhibited and "Airbag Off" warning light lit if switch is on "OFF" 100 Ω.
–Trigger lines authorised if the switch is on "ON" 400 Ω.
–Trigger lines inhibited, "Airbag Fault" and "Airbag Off" warning lights lit if a fault is detected, if the switch is not
configured and detected as present, or if there is a change of position outside of the conditions
MR-413-X44-88C000$308.mif
MRSZ AIRBAG
Vdiag: 04

88C-17
MR-413-X44-88C000$308.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - Function88C
By default, when the key is in the inhibition position, the following protections and signals are inhibited in the event of
a crash:
–Passenger front air bag.
–Passenger chest-level airbag, if fitted.
The passenger front airbag and passenger chest-level airbag are inhibited when the locking switch is
positioned on OFF or when DF028 "PASSENGER AIRBAG STATUS INDICATOR LIGHT CIRCUIT" or DF193
"PASSENGER AIRBAG LOCKING STATUS CHANGE" is present in the computer memory.
–Seat belt locking monitoring:
This function is carried out by the instrument panel (seat belt reminder indicator light and buzzer). The MRSZ
computer only sends the driver's seat belt buckle sensor status.
An instrument panel warning light indicates that the seat belt is not being worn by the driver and a beep sounds as a
reminder when the vehicle speed exceeds 12 mph (20 km/h).
–Monitoring the information displayed on the instrument panel:
The instrument panel controls the correct operation of the "Airbag fault" and "Airbag OFF" warning lights and
informs the airbag computer, via the multiplex network, of any possible malfunctions in the warning light circuits.

88C-18
MR-413-X44-88C000$385.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Replacement of components
REPLACING A SYSTEM COMPONENT
Disconnect the battery before removing and refitting any pyrotechnic component (airbag module,
pretensioner or seat belt retractor).
The computer must always be locked before any operation on a system component.
REPLACING THE AIRBAG COMPUTER
BEFORE REPLACING THE COMPUTER IT IS ESSENTIAL THAT YOU CONTACT THE TECHLINE.
To ensure that the returned computer's fault can be analysed, do not use command RZ001 "FAULT
MEMORY" when DF001 "COMPUTER" is present or stored.
The airbag computers are sold in locked mode to avoid all risk of accidental triggering (all trigger lines are inhibited).
The "locked" mode is indicated when the airbag fault warning light on the instrument panel lights up.
Follow this procedure to replace an airbag computer:
–check that the ignition is switched off,
–replace the computer,
–modify the computer configuration if necessary,
–enter the VIN into the computer with the diagnostic tool using command VP010 "WRITE VIN",
–switch off the ignition,
–carry out a check using the diagnostic tool,
–unlock the computer with command VP007 "UNLOCK COMPUTER", only if there are no faults indicated by the
diagnostic tool and check that the indicator light has gone out.
MR-413-X44-88C000$385.mif
MRSZ AIRBAG
Vdiag: 04

88C-28
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF028
PRESENT
PASSENGER AIRBAG STATUS WARNING LIGHT CIRCUIT
NOTESSpecial notes:
This fault may be "present" after command AC009 Instrument panel warning lights
is activated on the instrument panel.
Apply the fault finding procedure relevant to this fault in the instrument panel fault finding information section.
Carry out a fault finding procedure on the instrument panel (see 83A, Instrument panel).
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat a check using the diagnostic tool and, if there are no faults (do not take the
DF034 "Computer locked'' into account), unlock the computer using the command
VP007 ''Unlock computer''.
ABGMRSZ_V04_DF028P