sensor RENAULT TWINGO RS 2009 2.G Electrical Equipment - Airbags And Pretensioners Workshop Manual

88C-8
MR-413-X44-88C000$154.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - List and location of components88C
Version 10 trigger lines (continued)
Number Description
1Driver's frontal airbag
2Passenger frontal airbag
3Side chest-level airbag (passenger or driver)
4Rear curtain airbag (passenger or driver)
5Rear seat belt pyrotechnic retractor
6Lap belt pyrotechnic pretensioner (passenger and driver)
7Airbag computer
8Driver's seat belt buckle sensor
9Side impact sensor (passenger or driver)
10 Sensor for front passenger airbag inhibition by key
11 Instrument panel
12 Information to other systems (transmission via CAN)
(*) Component which can be deactivated by key

88C-10
MR-413-X44-88C000$154.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - List and location of components88C
Version: 6 trigger lines (continued)
Number Description
1Driver's frontal airbag
2Passenger frontal airbag
3Side chest-level airbag (passenger or driver)
4Lap belt pyrotechnic pretensioner (passenger or driver)
5Airbag computer
6Driver's seat belt buckle sensor
7Side impact sensor (passenger or driver)
8Instrument panel
9Sensor for front passenger airbag inhibition by key
10 Information to other systems (transmission via CAN)
(*) Component which can be deactivated by key

88C-12
MR-413-X44-88C000$154.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - List and location of components88C
Version: 4 trigger lines (continued)
Number Description
1Driver's frontal airbag
2Passenger frontal airbag
3Lap belt pyrotechnic pretensioner (passenger or driver)
4Airbag computer
5Driver's seat belt buckle sensor
6Sensor for front passenger airbag inhibition by key
7Instrument panel
8Information to other systems (transmission via CAN)
(*) Component which can be deactivated by key (according to fault finding configuration)

88C-13
MR-413-X44-88C000$154.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - List and location of components88C
1 - "Airbag Off" warning light:
The "airbag off" warning light is representative of the passenger airbag and passenger chest airbag inhibition status
if fitted.
–"off" = passenger airbag (switch on "ON") and passenger chest airbag (if fitted) active,
–"on" = passenger airbag (switch on "OFF" or fault detected on the switch line) and passenger chest
airbag (if fitted) inactive.
The "Airbag Fault" warning light comes on under the following conditions:
–detection and registering of an airbag system fault,
–a crash has been detected and registered,
–the computer is "crash locked" by the diagnostic tool,
–the computer must be programmed or reprogrammed.
2 - Passenger airbag inhibitor:
The passenger airbag inhibitor (by key) informs the airbag computer of a request to inhibit the passenger front airbag
and passenger chest airbag, if fitted.
3 - Driver's seat belt buckle sensor:
The seat belt buckle sensor gives the airbag computer the signal of whether the driver's belt is fastened or not.
4 - The driver and passenger buckle pyrotechnic pretensioners:
The buckle pyrotechnic pretensioner is integrated into the front seat belt buckle.
The pretensioner holds the occupant in the seat in the event of a crash.
5 - The driver and passenger rear seat belt pyrotechnic retractors:
The rear seat belt pyrotechnic retractor is integrated into the rear seat belt inertia reel.
The pyrotechnic seat belt retractor holds the occupant in the seat in the event of a crash.

88C-14
MR-413-X44-88C000$231.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Operating diagram
SYSTEM CONFIGURATION SHEET (FRONT section of the vehicle)
To rear wiring
Correct insulation value: display ≥ 100 h or 9999 flashing. A
B
C
D
E
GCentral unit
Driver’s seat
Front passenger seat (identical to the driver's
seat)
Front chest level side airbag ignition module
Driver's frontal airbag ignition module
Passenger's frontal airbag ignition moduleH
CT
PFront buckle pretensioner
Rotary switch + 12 V/Earth
Warning light / Diagnostic lines
Impact sensors/Impact signal
Passenger airbag locking switch/...
FRONT AIRBAGS
Measuring point Correct value
Driver C0, C2 and C4 1.2 to 5.8 Ω
Passenger C0 and C4 1.2 to 5.8 Ω
SIDE AIRBAGS AND PRETENSIONERS
Measuring point Correct value
C0, C1 and C3 1.2 to 5.8 Ω
MR-413-X44-88C000$231.mif
MRSZ AIRBAG
Vdiag: 04

88C-16
MR-413-X44-88C000$308.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Function
The MRSZ airbag computer takes control of all of the vehicle's restraint devices intended to ensure the protection of
the occupants (driver, front and rear passengers).
The MRSZ computer is designed to carry out the following functions:
●detection and confirmation of longitudinal impacts (front or rear) and/or side impacts,
●corresponding activation of the pyrotechnic restraint devices (e.g.: pretensioner, airbag),
●management of the different signals relating to the characteristics of the occupants (e.g.: presence detection),
●management of the function inhibiting the trigger lines and the passenger sensor,
●management and surveillance of the instrument panel "Airbag Fault" and "Airbag Off" warning lights via the
CAN network,
●activation of the "Crash output" signal via the CAN in the event of a crash,
●management of the fault finding signals (signals provided by the fault manager in response to fault finding
requests, whether this consists of internal faults or input/output fault finding).
Special notes:
–Frontal impacts:
This function is carried out using the MRSZ accelerometer. Accelerometers measure the violence of the impact. The
vehicle speed, the position of the passenger airbag locking switch and the accelerometer measurements determine
the strategy that the computer adopts to trigger the ignition modules. The front seat belt buckle pretensioners and
the front airbag may also be triggered or not depending on the input parameters.
–Side impacts:
This function is carried out by the MRSZ computer and the side impact sensors, if fitted.
The position of the passenger airbag locking switch and the accelerometer measurements determine the strategy
that the computer adopts to trigger the ignition modules. The front buckle pretensioners and the front chest-level
airbags and curtain airbags may also be triggered or not.
–Inhibition of passenger trigger lines:
This function is managed by the airbag computer, according to the position of the passenger airbag inhibition switch
and depending on the vehicle context.
The change in status of the inhibition switch must be done outside of after ignition feed. A change in status of the
switch is, however, authorised for 10 seconds after the after ignition feed for the vehicle is switched on.
If a change is status occurs outside of this 10 seconds, the computer will register a fault.
Inhibition programming:
–Trigger lines inhibited and "Airbag Off" warning light lit if switch is on "OFF" 100 Ω.
–Trigger lines authorised if the switch is on "ON" 400 Ω.
–Trigger lines inhibited, "Airbag Fault" and "Airbag Off" warning lights lit if a fault is detected, if the switch is not
configured and detected as present, or if there is a change of position outside of the conditions
MR-413-X44-88C000$308.mif
MRSZ AIRBAG
Vdiag: 04

88C-17
MR-413-X44-88C000$308.mif
V3
MRSZ AIRBAG
Vdiag: 04AIRBAGS AND PRETENSIONERS
Fault finding - Function88C
By default, when the key is in the inhibition position, the following protections and signals are inhibited in the event of
a crash:
–Passenger front air bag.
–Passenger chest-level airbag, if fitted.
The passenger front airbag and passenger chest-level airbag are inhibited when the locking switch is
positioned on OFF or when DF028 "PASSENGER AIRBAG STATUS INDICATOR LIGHT CIRCUIT" or DF193
"PASSENGER AIRBAG LOCKING STATUS CHANGE" is present in the computer memory.
–Seat belt locking monitoring:
This function is carried out by the instrument panel (seat belt reminder indicator light and buzzer). The MRSZ
computer only sends the driver's seat belt buckle sensor status.
An instrument panel warning light indicates that the seat belt is not being worn by the driver and a beep sounds as a
reminder when the vehicle speed exceeds 12 mph (20 km/h).
–Monitoring the information displayed on the instrument panel:
The instrument panel controls the correct operation of the "Airbag fault" and "Airbag OFF" warning lights and
informs the airbag computer, via the multiplex network, of any possible malfunctions in the warning light circuits.

88C-19
MR-413-X44-88C000$462.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Configurations and programming
CONFIGURATIONS/CONFIGURATION READING
The commands allow each component of the system to be configured separately to adapt the computer
configuration to the vehicle's actual equipment.
–Configuration reading commands (LCxxx), are used to check the status of the computer configuration in
relation to the trigger lines and vehicle sensors.
–Configuration commands (CFxxx), are used to adapt the computer configuration to the actual vehicle
fittings.
CONFIGURABLE FEATURES:
Trigger lines "WITH" or "WITHOUT"
Sensors "WITH or "WITHOUT"Diagnostic tool titleConfiguration
readingConfiguration
Passenger frontal airbag
Driver's frontal airbag
Driver's side curtain air bag
Passenger's side curtain air bag
Driver's front chest side air bag
Passenger front chest side air bag
Driver's front buckle pretensioner
Passenger front buckle pretensionerLC028
LC027
LC040
LC041
LC042
LC043
LC064
LC065CF210
CF209
CF221
CF222
CF223
CF224
CF265
CF266
Diagnostic tool titleConfiguration
readingConfiguration
Driver's front side impact sensor
Passenger front side impact sensor
Driver's seat belt buckle sensorLC082
LC083
LC073CF285
CF286
CF273
MR-413-X44-88C000$462.mif
MRSZ AIRBAG
Vdiag: 04

88C-21
MR-413-X44-88C000$539.mif
V3
88C
AIRBAGS AND PRETENSIONERS
Fault finding - Fault summary table
Tool faultAssociated
DTCDiagnostic tool title
DF0019080 Computer
DF0029042 Computer feed voltage
DF0039007 Driver's frontal airbag circuit
DF0049005 Passenger's front airbag circuit
DF0289041 Passenger airbag status warning light circuit
DF034907E Computer locked
DF0399035 Driver's side sensor circuit
DF0409036 Passenger's side sensor circuit
DF0609050 Multiplex network
DF068900C Passenger's chest front side airbag circuit
DF069900A Passenger side curtain airbag circuit
DF0709009 Driver's side curtain airbag circuit.
DF077900B Driver's front side chest airbag circuit
DF0919034 Airbag locking switch circuit
DF1659040 Airbag fault warning light circuit
DF1839012 Driver's side front buckle pretensioner circuit
DF1849013 Passenger side front buckle pretensioner circuit
DF193907C Passenger airbag locking status change.
DF194907F Computer to be replaced following impact
DF2329051 Driver's seat belt buckle sensor circuit
DF242907B Left-hand/right-hand drive configuration
DF2629050 Vehicle speed multiplex signal
DF2639050 No ABS/ESP multiplex signal
DF2649050 No instrument panel multiplex signal
MR-413-X44-88C000$539.mif
MRSZ AIRBAG
Vdiag: 04

88C-30
MR-413-X44-88C000$616.mif
V3
AIRBAGS AND PRETENSIONERS
Fault finding - Interpretation of faults
MRSZ AIRBAG
Vdiag: 04
88C
DF039
PRESENT
DRIVER'S SIDE SENSOR CIRCUIT
CC.1 : Short circuit to 12 volts
CC.0 : Short circuit to earth
1. DEF : Configuration
2. DEF : Sensor internal electronic fault
3. DEF : No communication
4. DEF : Consistent
CC.1, CC.0,
3.DEF
NOTESUse the Wiring Diagrams Technical Note, New TWINGO.
Lock the computer using command VP006 Lock computer.
Check the condition of the driver's side sensor connector, component code 1028 (see Wiring Diagrams
Technical Note, New Twingo, Component code 1028 and MR 411, Mechanical, 88C, Airbag and
pretensioners, Side impact sensor: Removal - Refitting).
Check the condition of the airbag computer connector, component code 756 (see Wiring Diagram Technical
Note, New Twingo, Component code 756 and MR 411, Mechanical 88C, Airbag and pretensioners, Airbag
computer: Removal - Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Use the "Universal bornier" to check the insulation to + 12 V, to earth and between the 2 lines of the following
connections:
–Connection code 60AH between components 756 and 1028,
–Connection code 60AG between components 756 and 1028.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
Use the "universal bornier" to check the continuity of the following connections:
–Connection code 60AH between components 756 and 1028,
–Connection code 60AG between components 756 and 1028.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the driver's side sensor component code 1028 (see MR 411, Mechanical, 88C,
Airbag and pretensioners, Side impact sensor: Removal - Refitting).
AFTER REPAIRClear the computer fault memory using command RZ001 "Fault memory". Switch
the ignition of f and then on again.
Repeat a check using the diagnostic tool and, if there are no faults (do not take the
DF034 "Computer locked'' into account), unlock the computer using the command
VP007 ''Unlock computer''.
ABGMRSZ_V04_DF039P