light RENAULT TWINGO RS 2009 2.G Electrical Equipment - Instrument Panel Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 66, PDF Size: 0.28 MB
Page 2 of 66
83A-2
MR-413-X44-83A000$056.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
Procedure
To run fault finding on the vehicle computers, switch on the ignition. Proceed as follows:
–turn the ignition key to APC,
–connect the diagnostic tool and perform the required operations.
To cut off the + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–turn the ignition key to OFF,
–verify that the forced + after ignition feed has been switched off by checking that the computer warning lights on
the control panel have gone out. Vehicle(s): New Twingo
Function concerned: Instrument panelName of computer: Instrument panel
3 levels:
–Entry Level version
–Mid Level version
–Top of the range version
Vdiag No.: 04, 08
Special tooling required
Multimeter
Elé. 1681 Universal bornier
TDB_V04_PRELI / TDB_V08_PRELI
Vdiag No.: 04, 08
MR-413-X44-83A000$056.mif
Page 5 of 66
83A-5
MR-413-X44-83A000$056.mif
V5
INSTRUMENT PANEL
Fault finding - Introduction
Vdiag No.: 04, 08
83A
4. FAULT FINDING PROCEDURE (CONTINUED)
Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Tactile inspection
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component
Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to the + 12 V feed or with another wire.
If a fault is detected, repair or replace the wiring harness.
Page 7 of 66
83A-7
MR-413-X44-83A000$112.mif
V5
83A
INSTRUMENT PANEL
Fault finding - List and location of components
Three models are available:
Entry level version: Multifunction display + Warning light display and a clock in place of the multimedia display.
The clock function is available on the trip computer.
Mid-range version: Multifunction display + Warning light display + Multimedia display. The clock function is available
on the multimedia display.
Top of the range version: Multifunction display + Warning light display + Multimedia display. The clock function is
available on the multimedia display.
1Multifunction display:
Rev counter/Fuel gauge
Multifunction line/Sequential gearbox
indicator/Cruise control-Speed limiter
indicator
Diesel preheating symbol
2Warning light display
3Multimedia display
On mid-range and top of the range
Vdiag No.: 04, 08
MR-413-X44-83A000$112.mif
Page 8 of 66
83A-8
MR-413-X44-83A000$112.mif
V5
INSTRUMENT PANEL
Fault finding - List and location of components
Vdiag No.: 04, 08
83A
1 Rev counter/Fuel gauge:
1Current speed display7Main beam indicator light
2Depress brake pedal symbol 8Dipped headlight indicator light
3“Economy” mode symbol9Side lights indicator light
4Sequential gear engaged10Multifunction display
5“Automatic” mode symbol11Fuel level gauge
6Cruise control/Speed limiter symbol12Diesel preheating symbol
Page 9 of 66
83A-9
MR-413-X44-83A000$112.mif
V5
INSTRUMENT PANEL
Fault finding - List and location of components
Vdiag No.: 04, 08
83A
2Warning light display:
1Brake warning light10“Service” warning light
2Major electric power-assisted steering fault
warning11
Rear fog lights indicator light
3Battery charge warning light12Front fog lights indicator light
4Oil pressure warning light13Direction indicator light
5Coolant temperature warning light14Passenger airbag disconnection warning light
6Particle filter warning light record
(Not used on the New Twingo)15Seat belt reminder indicator light
7On board diagnostics warning light16Door(s) open warning light
(Not present in the New Twingo)
8Airbag fault warning light17“Stop” warning light
9ABS warning light
Page 11 of 66
83A-11
MR-413-X44-83A000$168.mif
V5
INSTRUMENT PANEL
Fault finding - Operating diagram
Vdiag No.: 04, 08
83A
Multiplex network:
Input signals: 1Instrument panel computer
2ABS or vehicle speed circuit
3Sequential gearbox
4Airbag
5Rev counter
6Injection computer
7UCH
8+ after ignition feed
9Lighting dimmer
10Fuel sender
11Trip computer scroll button
12Parking brake
13Oil pressure
14EPAS
15Brake fluid level
16Side light
17Code
18Headlight
19Front fog light
20Rear fog light
21Battery supply
22Earth
23/24Left-hand and right-hand indicators
25Clock setting buttons (on entry level version)
Page 12 of 66
83A-12
MR-413-X44-83A000$168.mif
V5
INSTRUMENT PANEL
Fault finding - Operating diagram
Vdiag No.: 04, 08
83A
Output signals:
ABuzzer
BControlled warning lights:
–Seat belt reminder light
–Brake warning light
–Battery charge warning light
–Oil pressure warning light
–Coolant temperature warning light
–Airbag fault warning light
CFuel level display function
DOn-board computer
–Odometers
–Distance/time before service.
–Cruise control and speed limiter
–Clock (on entry level version)
–Exterior temperature display
ESequential gearbox display
FBacklighting
Dimmer
GSpeedometer
HDirect warning lights:
–Side light indicator light
–Dipped headlight indicator light
–Headlight indicator light
–Front fog light indicator light
–Rear fog light indicator light
–Direction indicator light
Page 13 of 66
83A-13
MR-413-X44-83A000$224.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Function
The instrument panel provides the following functions:
–Illumination of the direction indicator light:
The dual direction indicator light comes on if the driver has manipulated the indicator switch to inform of a change in
direction.
–Illumination of the light indicator lights:
–The side light indicator light comes on when the side lights are switched on.
–The dipped headlights indicator light comes on when the dipped headlights are switched on.
–The main beam headlights indicator light comes on when the main beam headlights are switched on.
–The front fog light indicator light comes on when the front fog lights are switched on.
–The rear fog light indicator light comes on when the rear fog lights are switched on.
–Side lights reminder buzzer:
–The “side lights reminder” buzzer sounds when the driver's or passenger's door is opened, with the APC off and
the side lights on, to warn the driver that the lights are still on.
–Operation of the “automatic headlighting activation - deactivation or automatic locking when driving”
buzzer:
–The “connection” warning sound is emitted by the instrument panel buzzer when the “automatic headlighting” or
“automatic locking when driving” functions are activated.
–The “disconnection” warning sound is emitted by the instrument panel buzzer when the “automatic headlighting” or
“automatic locking when driving” functions are deactivated.
–“Overspeed function - Arabia” buzzer operation:
Warns the driver that the speed threshold has been exceeded, depending on the country and the equipment.
Vdiag No.: 04, 08
MR-413-X44-83A000$224.mif
Page 14 of 66
83A-14
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function
Vdiag No.: 04, 08
83A
– Fuel level gauge:
The fuel level gauge informs the driver of the fuel level remaining in the tank using a bargraph. It also indicates a low
fuel level using a “fuel level low” warning consisting of a flashing red square.
–Speed display:
The speed display informs the driver of the current vehicle speed in km/h or miles/h depending on the
“distance units” configuration.
If the “Service” warning light and " - - " light up in place of the vehicle speed, refer to the “Service warning light
illumination” insert.
–Multifunction display:
The multifunction display centralises the following information:
–Mileometer,
–Trip mileage.
–Distance/time before service
–Cruise control/Speed limiter (depending on configuration)
–Clock (entry level version)
–Exterior temperature (depending on configuration)
It is possible to shift from one piece of information to another in the order above, simply by pressing the
“Trip computer” button located on the end of the windscreen washer control.
–Mileometer and trip mileage:
Respectively indicates the total distance travelled by the vehicle since it was manufactured and the distance
travelled since the trip mileage was last reset.
The distance travelled is displayed in “km” or “miles” depending on the configuration.
–Distance/time before service:
Shown on the multifunction display, indicates the distance to be travelled before the next service.
If the “Service” warning light and “Distance/time before service” warning light come on simultaneously, refer to the
“Service warning light illumination” insert.
Page 15 of 66
83A-15
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function
Vdiag No.: 04, 08
83A
–“Cruise control/speed limiter” symbol display:
The Cruise control or Speed limiter symbol comes on when the system is switched on and is also displayed with the
selected reference speed on the multifunction display in km/h or miles/h, depending on the configuration.
If the “Service” warning light and “Cruise control/Speed limiter” symbol(s) come on simultaneously, refer to the
“Service warning light illumination” insert.
–Clock:
Displays the time.
–External temperature indicator:
Informs the driver of the external temperature.
–Illumination of the “Brake” warning light:
Illumination of the “brake” warning light indicates the following statuses to the driver:
–Fixed illumination: Parking brake engaged/Test phase when vehicle under + after ignition feed.
–Fixed illumination + 5 seconds buzzer: Parking brake engaged when driving.
–Flashing: Calibration of the electronic braking distribution.
If the “Stop” warning light and “Brake” warning light come on simultaneously, refer to the “Stop warning light
illumination” insert.
–Illumination of the “seat belt reminder” warning light:
Illumination of the “seat belt reminder” warning light indicates the following statuses to the driver:
–Fixed illumination: Seat belt reminder.
–Flashing + “Moderate seat belt reminder buzzer” signal:
Seat belt reminder + 12 mph (20 km/h).
–Flashing + “Loud seat belt reminder buzzer” signal + Radio cut off:
Seat belt reminder following the seat belt reminder warning + 12 mph (20 km/h).