sensor RENAULT TWINGO RS 2009 2.G Electrical Equipment - Instrument Panel Workshop Manual

83A-23
MR-413-X44-83A000$392.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Fault summary table
Tool fault Associated DTC Diagnostic tool title
DF0079402 Fuel sender circuit
DF0099407 Oil pressure sensor circuit
DF0189405 Instrument panel
DF0199404 Battery voltage
Vdiag No.: 04, 08
MR-413-X44-83A000$392.mif

83A-26
MR-413-X44-83A000$448.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of faults

Vdiag No.: 04, 08
83A
DF009
PRESENT
OIL PRESSURE SENSOR
1.DEF: Signal incoherent
NOTESSpecial note:
This check must be carried out with the engine stopped.
1.DEF
NOTESThe fault is declared present if the oil pressure sensor is not
detected as closed when the engine is stopped.
Top up the oil level before starting the check.
Look for any damage to the wiring harness and check the condition and connection of the oil pressure switch
and its connections.
Look for possible damage to the wiring harness, check the connection and condition of the instrument panel
connector.
If there is a repair method (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair)
repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connection:
Connection 28A between component 205 and component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_DF009P / TDB_V08_DF009P

83A-30
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Fault signalET249:Service warning
light activated by
the system1-Multiplex line
communication
2- Injection
3-Water present in diesel
fuel
4-Sequential gearbox
5-Vehicle speed circuit
6-Cruise control/speed
limiter
7-ESP
8-ABS
9-Oil change interval
10- Particle filter
11- Airbag
12- OBDSee the interpretation of
ET249 SERVICE warning
light activated by the
system
Parking brake
signalET097:Parking brakeAutomatic
parking brake
onAPPLIED
In the event of a fault, consult
the interpretation of status
ET097 Parking brake Parking
brake
releasedRELEASED
Minimum brake
fluid level signalET019:Minimum brake
fluid levelMinimum
brake fluid
reservoir
levelYES
In the event of a fault, consult
the interpretation of status
ET019 Minimum brake fluid
level. Normal brake
fluid
reservoir
levelNO
Oil pressure
present signalET096:Oil pressure
contactEngine
runningOPENIn the event of a fault,
consult the interpretation of
fault DF009 “oil pressure
sensor” Engine
stoppedCLOSED

83A-36
MR-413-X44-83A000$616.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of statuses

Vdiag No.: 04, 08
83A
ET019
MINIMUM BRAKE FLUID LEVEL
NOTESThere must be no present or stored faults.
Check the brake fluid level in the reservoir.
If the brake fluid is at the maximum level and ET019 MINIMUM BRAKE FLUID LEVEL is “YES”:
Disconnect the connector on component 207.
If status ET019 MINIMUM BRAKE FLUID LEVEL becomes NO, replace component 207.
Check the earth insulation of:
connection 30A between component 247 and component 207.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the brake fluid is at the minimum level and ET019 MINIMUM BRAKE FLUID LEVEL is “NO”:
Disconnect the connector on the Brake fluid minimum level sensor, component code 207.
Check for continuity between connection 30A and connection MAS of the Brake fluid minimum level sensor,
component code 207.
If there is no continuity, replace the Brake fluid minimum level sensor, component code 207.
Check for continuity:
On connection 30A between component 207 and component 247.
On connection MAS between component 207 and the vehicle earth.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET019 / TDB_V08_ET019

83A-49
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
83A
Vdiag No.: 04 08
ALP 1NO COMMUNICATION WITH THE INSTRUMENT PANEL.
The instrument panel does not light up.
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
See Wiring diagram Technical Note, New Twingo.
Test the diagnostic tool on another vehicle which is in perfect working order.
Check that the sensor's green indicator light comes on.
If communication with the second vehicle is impossible, follow the instructions in the CLIP diagnostic tool test
section.
If dialogue with the first vehicle is possible, follow the instructions in the Vehicle check section.
DIAGNOSTIC
TOOL CHECKCheck the cleanliness and condition of the contacts of the diagnostic socket,
component code 225 connected to the vehicle.
Check the condition of the cable from the diagnostic socket to the sensor and the
cleanliness and condition of the connections.
Check the sensor connections.
Check the condition of the cable from the CLIP tool to the sensor as well as the
condition and cleanliness of the connections.
Check the cleanliness and condition of the CLIP socket.
If the connector or connectors are faulty and if there is a repair procedure (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact Techline.
TDB_V04_ALP1/TDB_V08_ALP1
INSTRUMENT PANEL
Fault finding - Fault finding chart

83A-50
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V5 MR-413-X44-83A000$952.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart Vdiag No.: 04, 0883A
Vdiag No.: 04 08
ALP 1
CONTINUED 1
VEHICLE CHECK
Check the cleanliness and condition of the contacts of the diagnostic socket,
component code 225 connected to the vehicle.
Check the condition of the cable from the diagnostic socket to the sensor and the
cleanliness and condition of the connections.
Check the sensor connections.
Check the condition of the cable from the sensor to the CLIP tool and the cleanliness
and condition of the connections.
Check the cleanliness and condition of the CLIP socket.
If the connector or connectors are faulty and if there is a repair procedure (see
Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair), repair the connector, otherwise replace the wiring.
If the fault is still present, contact Techline.
Check the condition and connection of the instrument panel connector, component
code 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check instrument panel supply fuse MIN (5 A), component code 247 on the passenger
compartment fuse box, component code 1016 and the condition and cleanliness of
the contacts.
Check the instrument panel after ignition supply fuse MIN (15 A), component code
247 on the passenger compartment fuse box, component code 1016, and the
condition and cleanliness of the contacts.