trip computer RENAULT TWINGO RS 2009 2.G Electrical Equipment - Instrument Panel Workshop Manual

83A-7
MR-413-X44-83A000$112.mif
V5
83A
INSTRUMENT PANEL
Fault finding - List and location of components
Three models are available:
Entry level version: Multifunction display + Warning light display and a clock in place of the multimedia display.
The clock function is available on the trip computer.
Mid-range version: Multifunction display + Warning light display + Multimedia display. The clock function is available
on the multimedia display.
Top of the range version: Multifunction display + Warning light display + Multimedia display. The clock function is
available on the multimedia display.
1Multifunction display:
Rev counter/Fuel gauge
Multifunction line/Sequential gearbox
indicator/Cruise control-Speed limiter
indicator
Diesel preheating symbol
2Warning light display
3Multimedia display
On mid-range and top of the range

Vdiag No.: 04, 08
MR-413-X44-83A000$112.mif

83A-11
MR-413-X44-83A000$168.mif
V5
INSTRUMENT PANEL
Fault finding - Operating diagram

Vdiag No.: 04, 08
83A
Multiplex network:
Input signals: 1Instrument panel computer
2ABS or vehicle speed circuit
3Sequential gearbox
4Airbag
5Rev counter
6Injection computer
7UCH
8+ after ignition feed
9Lighting dimmer
10Fuel sender
11Trip computer scroll button
12Parking brake
13Oil pressure
14EPAS
15Brake fluid level
16Side light
17Code
18Headlight
19Front fog light
20Rear fog light
21Battery supply
22Earth
23/24Left-hand and right-hand indicators
25Clock setting buttons (on entry level version)

83A-14
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function

Vdiag No.: 04, 08
83A
– Fuel level gauge:
The fuel level gauge informs the driver of the fuel level remaining in the tank using a bargraph. It also indicates a low
fuel level using a “fuel level low” warning consisting of a flashing red square.
–Speed display:
The speed display informs the driver of the current vehicle speed in km/h or miles/h depending on the
“distance units” configuration.
If the “Service” warning light and " - - " light up in place of the vehicle speed, refer to the “Service warning light
illumination” insert.
–Multifunction display:
The multifunction display centralises the following information:
–Mileometer,
–Trip mileage.
–Distance/time before service
–Cruise control/Speed limiter (depending on configuration)
–Clock (entry level version)
–Exterior temperature (depending on configuration)
It is possible to shift from one piece of information to another in the order above, simply by pressing the
“Trip computer” button located on the end of the windscreen washer control.
–Mileometer and trip mileage:
Respectively indicates the total distance travelled by the vehicle since it was manufactured and the distance
travelled since the trip mileage was last reset.
The distance travelled is displayed in “km” or “miles” depending on the configuration.
–Distance/time before service:
Shown on the multifunction display, indicates the distance to be travelled before the next service.
If the “Service” warning light and “Distance/time before service” warning light come on simultaneously, refer to the
“Service warning light illumination” insert.

83A-31
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
SUB-FUNCTION: TRIP COMPUTER
*ADAC: Trip Computer
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Instrument panel
warning light
operation checkAC009:Instrument
panel warning
lightsIllumination of all of the
warning lights
simultaneously on the
displayImportant: This command
causes the Airbag system
stored fault to occur again
(see 88C Airbag and
pretensioners).
–Before running the
command:
Deal with all of the Airbag
faults.
(see 88C, Airbag and
pretensioners).
–After running the
command:
Clear the Airbag system
stored faults.
If one or more warning lights
do not come on, contact
Techline.
Backlighting
operation checkAC010:LightingGradual illumination of
the instrument panel
backlightingWITHOUT
Instrument panel
buzzer checkAC006:BuzzerInstrument panel buzzer
operation–If the buzzer is faulty,
contact Techline.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
ADAC* button
status signalET030:ADAC* scroll
button
Button
depressedDEPRESSED
In the event of a fault, consult the
interpretation of status ET030
ADAC* scroll button.
Button
releasedRELEASED
Clock setting
button status
signalET095:Clock setting
button
Button
depressedDEPRESSED
Contact the Techline.Button
releasedRELEASED

83A-34
MR-413-X44-83A000$560.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Status summary table
*ADAC: Trip Computer Tool status Diagnostic tool title Specification
ET004Side lights control Inactive/Active
ET019Minimum brake fluid level Yes/No
ET030ADAC* scroll button Released/Pressed
ET095Clock setting button Released/Pressed
ET097Parking brake Engaged/Released
ET245Direction indicators Inactive/Active
ET248Stop warning light activated by the
system1 : Injection
2 : Coolant temperature
3 : Oil pressure
4 : Brake fluid level
5 : Electronic Braking Distribution
6 : Electric power assisted steering
7 : Battery charge
ET249Service warning light activated by the
system1 : Multiplex line communication
2 : Injection
3 : Water present in diesel fuel
4 : Sequential gearbox
5 : Vehicle speed circuit
6 : Cruise control/speed limiter
7 : ESP
8 : ABS
9 : Oil service interval
10 : Particle filter
11 : Airbag
12 : OBD

Vdiag No.: 04, 08
MR-413-X44-83A000$560.mif

83A-37
MR-413-X44-83A000$616.mif
V5

Vdiag No.: 04, 08INSTRUMENT PANEL
Fault finding - Interpretation of statuses83A
ET030
ADAC* SCROLL BUTTON
NOTESVehicle under + after ignition feed.
“RELEASED”
STATUS
button
pressed
*ADAC: Trip ComputerCheck the condition and connection of the instrument panel connector,
component code 247.
Press and hold the Trip Computer button and check the continuity between
connection MAM and connection 47K of component 145.
If there is no continuity, replace component 145 (see MR 411, Mechanical, 84A,
Controls - Signals, Wiper switch: Removal - Refitting).
Check the continuity and insulation to + 12 V on:
Connection 47K between component 145 and component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
Check the earth and insulation to + 12 V of:
–Connection MAN between component 145 and the chassis earth.
–Connection MAN between component 145 and the chassis earth.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_ET030 / TDB_V08_ET030