lights RENAULT TWINGO RS 2009 2.G Electrical Equipment - Lightening Owner's Guide

80D-39
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 9Lights are not switched off after switching off the + after ignition
feed and the driver's door opening
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check, as a priority, the operation of status ET115 "Request to switch on the lights
via the light sensor" and commands AC054 Dipped headlights and AC055 Side
lights in the UCH.
Note:
For the lights to switch off automatically after driving, the following conditions must all be met:
–engine stopped,
–ignition: 0 (inactive),
–vehicle speed > 0 mph (0 km/h),
–driver's door: closed.
Carry out a multiplex network test. If the multiplex
network contains faults (see 88B, Multiplexing).
Check the operation of status ET142 "Engine
operating phase".
Is the status functioning correctly?
YES
Make sure that status ET239 Ignition switch
position is working.
Is the status functioning correctly?
YES
NOApply the procedure for processing status
ET142.
NOApply the procedure for processing status
ET239.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP9

80D-41
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 10 Lights not switching on at night
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
The engine must be running in order for the automatic lighting function to operate and
the system must be equipped with a rain/light sensor.
Check, as a priority, the operation of status ET115 "Request to switch on the lights
via the light sensor" in the UCH. Check that the following faults are not present:
–DF011 "Rain/light sensor circuit",
–DF135 "Rain sensor",
–DF136 "Light sensor".
Deal with the above faults if they are present.
Note:
The sensor requests the lights to be switched on when there is poor light intensity (at night, in a tunnel, etc.).
Check whether the vehicle has a rain/light sensor. If the vehicle does not have a rain/light sensor, explain to the
customer that this is normal, and that the vehicle does not have this feature.
Activate the automatic lighting function by switching
the side lights on and off twice in succession:
a beep will sound to confirm this.
Did a beep sound?
YES
NORefer to the interpretation of status ET081
"Lighting stalk position".
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP10

80D-43
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 11 No See-me-home lighting
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check whether the vehicle has a rain/light sensor. If the vehicle does not have a rain/light sensor, explain to the
customer that this is normal, and that the vehicle does not have this feature.
Check that LC025 "See-me-home lighting" is "With", otherwise use CF032 "See-me-home lighting".
Check that the ignition is switched off.
Flash the headlights one or more times (as required) to activate the See-me-home lighting function.
Check that the horn and lights switch is operating correctly using status ET081 "Lighting stalk position". In the
event of a fault with the horn and lights switch, refer to the interpretation of status ET081 "Lighting stalk
position".
Use the following commands to check that the side lights, dipped headlights and main beam headlights are
operating correctly.
–AC055 "Side lights",
–AC054 "Dipped headlights",
–AC062 "Main beam headlights".
In the event of a fault, refer to the interpretation of the following faults:
–DF087 "Side lights relay control circuit",
–DF088 "Dipped headlights relay control circuit",
–DF098 "Main beam headlights relay control circuit".
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP11

80D-44
MR-413-X44-80D000$900_eng.mif
V1
LIGHTING
Fault finding - Fault Finding Chart80D
ALP 12 No courtesy lights
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Check that fault DF139 "Courtesy lights" is not present. Deal with the fault if it is
present.
Check the conformity of status ET463 "Door(s) or tailgate" (see 87B, Passenger compartment connection
unit).
Check that LC121 "Gradual lighting and dimming of the courtesy lights" is "With", otherwise use CF031
"Calibration".
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP12