ignition RENAULT TWINGO RS 2009 2.G Electrical Equipment - Petrol Injection Workshop Manual

17B-252V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET673JAMMED ACCELERATOR PEDAL–YES
–NO
STATUS
DEFINITIONYES: This status indicates that the accelerator pedal is detected to be jammed.
NO: This status indicates that the accelerator pedal is not detected to be jammed.
NOTESSpecial notes:
Apply this procedure only if the status is YES.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
YES
OR
NOThis status varies when the ignition is on or the engine is running depending on the
status of the accelerator pedal.
Check the condition of the connectors of the brake switch (component code 160), of the accelerator potentiometer
(component code 921), and of the engine management computer (component code 120).
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
SIM32_V44_ET673 / SIM32_V4C_ET673 / SIM32_V50_ET673 / SIM32_V54_ET673
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-254V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET674REFRIGERANT PRESSURE–Too low
–Correct
–Unavailable
STATUS
DEFINITIONTOO LOW: this status indicates that the refrigerant pressure is too low.
CORRECT: this status indicates that the refrigerant pressure is correct.
UNAVAILABLE: this status indicates that the refrigerant pressure is unavailable.
NOTESDeal with DF232 Refrigerant pressure sensor circuit first.
There must be no present or stored faults.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
TOO LOW
or
CORRECT
or
"UNAVAILABLE"The purpose of this status is to check that the circuit is correctly charged with gas.
It becomes active when the air conditioning is detected as being connected and there
are no faults present.
The result of this status is:
–Too low: Pressure below 2 bar.
–Correct: Pressure above 2 bar.
–Unavailable: Cannot perform test.
SIM32_V44_ET674 / SIM32_V4C_ET674 / SIM32_V50_ET674 / SIM32_V54_ET674
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-255V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET703CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS
DEFINITIONRESUME: R button pressed.
SUSPEND: 0 button pressed.
INCREASE: Increase button pressed.
MINUS: Decrease button pressed.
INACTIVE: This status indicates that no button has been pressed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"INACTIVE"When no button has been pressed.
In the event of a fault, refer to the interpretation of status ET703.
"SUSPEND"'0' button pressed.
In the event of a fault, refer to the interpretation of status ET703.
"REACTIVATE"'R' button pressed.
In the event of a fault, refer to the interpretation of status ET703.
SIM32_V44_ET703 / SIM32_V4C_ET703 / SIM32_V50_ET703 / SIM32_V54_ET703
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-260V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET704
ET705BRAKE SWITCH NO. 1BRAKE SWITCH NO. 2
STATUS
DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE: This status indicates that the brake pedal is released.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Note:
Statuses ET704 and ET705 should change status at the same time. If there is
inconsistency, refer to the interpretation of faults DF228 Brake signals and DF623
Closing brake signal.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
"ACTIVE"Brake pedal depressed.
Brake signal non-conformity may cause the engine to race during gear changes.
"INACTIVE"Brake pedal released.
Brake signal non-conformity may cause the engine to race during gear changes.
SIM32_V44_ET704 / SIM32_V4C_ET704 / SIM32_V50_ET704 / SIM32_V54_ET704
SIM32_V44_ET705 / SIM32_V4C_ET705 / SIM32_V50_ET705 / SIM32_V54_ET705
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-262V7 MR-413-X44-17B000$153.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 50 and 54
ET840CUSTOMISED OIL CHANGE INTERVAL
STATUS
DEFINITIONACTIVE: This status indicates that the OCS function is active.
INACTIVE: This status indicates that the OCS function is inactive.
NOTESNone.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
ACTIVE
or
INACTIVE
This status indicates if the vehicle offers the OCS (Oil Control System) function, i.e.
the customised oil change interval.
SIM32_V50_ET840 / SIM32_V54_ET840
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-264V7 MR-413-X44-17B000$160.mif
PETROL INJECTION
Fault finding – Parameter summary table17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
OCR*: Opening cyclic ratio
Heat.*: Heating
Tool ParameterDiagnostic tool title
PR125Power consumed by the air conditioning compressor
PR126Advance after anti-pinking correction
PR127Heat.* resistor maximum authorised power
PR130Cruise control setpoint
PR138Richness correction
PR143Self-adapting richness gain
PR144Self-adapting richness offset
PR147Pedal potentiometer voltage gang 1
PR148Pedal potentiometer voltage gang 2
PR190Engine idle speed setpoint.
PR312Inlet manifold vacuum
PR424Programming the no-load position value
PR427Average pinking signal
PR429Measured throttle position
PR448Ignition advance
PR538Measured throttle voltage, gang 2
PR539Measured throttle voltage gang 1
PR568Pedal position gang 1
PR569Pedal position gang 2
PR587Motorised throttle lower stop gang 1
PR588Motorised throttle lower stop gang 2
PR589Motorised throttle upper stop gang 1
PR590Motorised throttle upper stop gang 2
PR632Controlled coolant thermostat OCR* (Vdiag 4C only)
PR743Estimated alcohol level in the tank (CLIO III or MODUS only)
PR744Engine temperature setpoint (Vdiag 4C only)
PR745Camshaft dephaser position setpoint (Vdiag 4C only)
PR746Camshaft dephaser position (Vdiag 4C only)
PR873Oil oxidation signal (except D7F800 and D4F772)
PR874Last overhaul (except D7F800 and D4F772)
PR926Alcohol fuel adaptive correction (CLIO III or MODUS only)

17B-265V7 MR-413-X44-17B000$171.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR014IDLE SPEED CORRECTION
PARAMETER
DEFINITIONThis parameter indicates the engine's rotational speed in rpm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running and engine coolant
temperature > 80˚C
This status indicates the engine idle speed correction value.
The value should be between:
0 rpm < PR014 < 224 rpm.
The idle speed regulator performs all of the calculations that allow the idle speed actuator to be controlled
physically: the motorised throttle. The functional component of the regulator is adaptive (variation programming
and ageing).
SIM32_V44_PR014/SIM32_V4C_PR014/SIM32_V50_PR014/SIM32_V54_PR014
PETROL INJECTION
Fault finding – Interpretation of parameters
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-267V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR018ESTIMATED AIR FLOW
PARAMETER
DEFINITIONThis parameter indicates the inlet air flow in kg/h.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
There must be no faults present.
Perform this fault finding procedure:
–after finding an inconsistency in the parameter,
–or after a customer complaint (lack of power, smoke etc.).
Conformity check with engine stopped and ignition on.
Indicates the inlet air flow in kg/h.
The value should be:
X = 0 kg/h
Conformity check with the engine running and engine coolant temperature > 80˚C
Indicates the inlet air flow in kg/h.
The value should be:
X ≈ 7 kg/h
SIM32_V44_PR018/SIM32_V4C_PR018/SIM32_V50_PR018/SIM32_V54_PR018
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-268V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR030ACCELERATOR PEDAL POSITION
PARAMETER
DEFINITIONThis parameter indicates the accelerator pedal position in %.
NOTESSpecial notes:
Only carry out these checks if PR030 > 15% with No load or if PR030 < 90% with
Full load.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III or
MODUS.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
If there is no pressure on the pedal X = 0%
In the event of a fault, consult the interpretation of fault DF196 Pedal sensor circuit gang 1 or DF198 Pedal
sensor circuit gang 2.
Sensor electrical conformity
Check that the pedal mechanism has not seized.
Check the condition of the accelerator potentiometer connector (component code 921) and the engine
management computer connector (component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
SIM32_V44_PR030/SIM32_V4C_PR030/SIM32_V50_PR030/SIM32_V54_PR030
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-270V7 MR-413-X44-17B000$171.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
PR035ATMOSPHERIC PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the atmospheric pressure in bar. The sensor is integrated in
the computer.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Use the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
The atmospheric pressure value is:
PR035 ≈ 1 bar +/- 0.20 bar
In the event of a fault, consult the interpretation of DF004 Turbocharging pressure sensor circuit.
Check the cleanliness and condition of the atmospheric pressure sensor and its connections (component
code 147) and the engine management computer (component code 120).
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
On the atmospheric pressure sensor, component code 147, check the resistance between connections 3LG
and 3CK.
If the resistance is not X 50 kΩ, replace the sensor.
SIM32_V44_PR035/SIM32_V4C_PR035/SIM32_V50_PR035/SIM32_V54_PR035
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.