ABS RENAULT TWINGO RS 2009 2.G Electrical Equipment - Petrol Injection Owner's Manual

17B-171V7 MR-413-X44-17B000$151.mif
17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET001COMPUTER + AFTER IGNITION FEED
STATUS
DEFINITIONPRESENT: This status indicates that the + after ignition feed is active.
ABSENT: This status indicates that the + after ignition feed is not active.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"PRESENT"
Ignition on and engine running warm at idle speed with the + after ignition feed
activated.
In the event of a fault, apply the interpretation of DF046 Battery voltage.
"ABSENT"If the + after ignition is not activated, ET001 is "Absent".
In the event of a fault, apply the interpretation of DF046 Battery voltage.
SIM32_V44_ET001/SIM32_V4C_ET001/SIM32_V50_ET001/SIM32_V54_ET001
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
PETROL INJECTION
Fault finding – Interpretation of statuses

17B-181V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET023FAST IDLE SPEED REQUEST–Present
–Absent
STATUS
DEFINITIONPRESENT: The status indicates that the fast idle speed request is active.
ABSENT: The status indicates that the fast idle speed request is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Refer to the Wiring Diagrams Technical Note for NEW TWINGO, E33, CLIO III
or MODUS.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
PRESENT
OR
ABSENTUCH requests the injection system to increase the idling speed.
ABSENT: The UCH has not formulated a request.
PRESENT: The UCH has formulated a request.
If ET023 is inconsistent, test the multiplex network using the diagnostic tool
(see 88B, Multiplexing). If the test is correct, refer to the UCH fault finding procedure
(see 87B, Passenger compartment connection unit) and for Clio III or Modus,
run fault finding on the Protection and Switching Unit (see 87G, Engine
compartment connection unit).
SIM32_V44_ET023/SIM32_V4C_ET023/SIM32_V50_ET023/SIM32_V54_ET023
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-186V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042
CONTINUED 2
"INACTIVE"
When the main button is in rest position (or Neutral), status ET042 Cruise control/
speed limiter is INACTIVE.
If CRUISE CONTROL or SPEED LIMITER appears despite the main switch being in
the rest (or neutral) position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check for +12 V after ignition on the switch connector on the following connection:
●AP10 of component 1081.
Disconnect the switch and with it in the rest position, check the insulation between
the following connections:
●AP10 and 3FX of component 1081.
●AP10 and 3PD of component 1081.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the speed limiter position.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the insulation, continuity, and the absence of interference resistance on
the following connections:
●3FX between components 1081 and 120,
●3PD between components 1081 and 120.
Also check:
The engine management computer connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-187V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042
CONTINUED 3
LIMITER
When the driver presses the speed limiter switch, status ET042 Cruise control/
speed limiter becomes SPEED LIMITER.

If CRUISE CONTROL or INACTIVE appears although the driver pressed the switch
in the speed limiter position, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check for +12 V after ignition feed on the switch connector.
●AP10 of component 1081.
Disconnect the switch and when it is in the rest position, check the insulation
between:
●AP10 and 3FX of component 1081,
●AP10 and 3PD of component 1081.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the speed limiter position.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the cruise control position.
If these checks are not in order, replace the switch.
Check the insulation, continuity, and the absence of interference resistance on
the following connections:
●3FX between components 1081 and 120,
●3PD between components 1081 and 120.
Also check:
The engine management computer connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-188V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET042
CONTINUED 4
CRUISE
CONTROL
When the driver presses the cruise control switch, status ET042 Cruise control/
speed limiter becomes CRUISE CONTROL.
If SPEED LIMITER or INACTIVE appears even though the cruise control button is
pressed, carry out the following operations:
Check the connections of the cruise control/speed limiter main switch.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
Check for +12 V after ignition feed on the switch connector.
●AP10 of component 1081.
Disconnect the switch and when it is in the rest position, check the insulation
between:
●AP10 and 3FX of component 1081,
●AP10 and 3PD of component 1081.
–Check the continuity between connections AP10 and 3PD of component 1081 in
the speed limiter position.
–Check the continuity between connections AP10 and 3FX of component 1081 in
the cruise control position.
If the results of the checks are not correct, replace the switch.
Check the insulation, continuity, and the absence of interference resistance on
the following connections:
●3FX between components 1081 and 120,
●3PD between components 1081 and 120.
Also check:
The engine management computer connections.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector,
otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-190V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET048ACTUATOR RELAY CONTROL
STATUS
DEFINITIONACTIVE: The status indicates that the control is active.
INACTIVE: The status indicates that the control is inactive.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system operation
programming.
Conformity check: Engine stopped and ignition on, or engine running at idle speed, and engine coolant
temperature > 80˚C.
"INACTIVE"
or
ACTIVEThis relay supplies the following actuators: the injectors, the throttle valve control,
the oxygen sensor heating, the bleed solenoid valve, the fuel vapour absorber
and connection 3FB of the injection computer.
In the event of a fault, see the interpretation of fault DF084 Actuator relay control
circuit.
SIM32_V44_ET048/SIM32_V4C_ET048/SIM32_V50_ET048/SIM32_V54_ET048
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-196V7 MR-413-X44-17B000$151.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET054
CONTINUED
IDLING SPEED TOO LOW
Check:
–engine oil level (too high, splashing),
–that the exhaust pipe is not blocked (catalytic converter damaged),
–the cleanliness and conformity of the air filter,
–that the air inlet circuit is not blocked,
–that the throttle valve assembly is not clogged,
–the condition and conformity of the spark plugs,
–the fuel circuit sealing,
–the fuel pressure and the flow (see MR 392 (Clio III), MR 385 (Modus), MR 411 (New Twingo), or MR 442
(E33), Mechanical, 13A, Fuel supply),
–the condition and cleanliness of the injectors,
–the cylinder compression's,
–the timing setting.
Repair or replace the faulty components, if necessary.
IDLING SPEED TOO HIGH
Check:
–engine oil level (too high, splashing),
–for the fittings in the oil vapour rebreathing system,
–the sealing between the throttle valve and inlet manifold,
–the manifold pressure sensor sealing,
–the fuel vapour absorber bleed, which must not be jammed open,
–the fuel vapour absorber bleed system sealing,
–the brake servo system sealing,
–the sealing between the inlet manifold and cylinder head,
–the oil vapour recovery circuit sealing between the inlet manifold and cylinder head,
–the fuel pressure and the flow (see MR 392 (Clio III), MR 385 (Modus), MR 411 (New Twingo), or MR 442
(E33), Mechanical, 13A, Fuel supply),
–the condition and cleanliness of the injectors,
–the cylinder compression's,
–the timing adjustment,
Repair or replace the faulty components, if necessary.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

17B-225V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET351INJECTION ELECTRONIC STABILITY PROGRAM CONNECTION
STATUS
DEFINITIONCONNECTED: This status indicates that the connection between the injection
computer and the ESP is not defective.
DISCONNECTED: This status indicates that the connection between the injection
computer and the ESP is defective.
NOTESSpecial notes:
Perform these checks if the parameters correspond with the system operation
programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80˚C
NOT CONNECTEDThe connection between the injection computer and the ESP is defective, test the
ABS/ESP computer (see 38C, Anti-lock braking system) and the multiplex network
(see 88B, Multiplexing).
SIM32_V44_ET351/SIM32_V4C_ET351/SIM32_V50_ET351/SIM32_V54_ET351
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-227V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET405
CONTINUED
Sensor electrical conformity
"INACTIVE"Check the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch, check the insulation between connections M and
86D of component 675, with the switch in the rest position.
–Repeat this operation with the switch engaged, and check the continuity between
the two connections.
If these 2 checks are faulty, replace the switch.
Then check the continuity and absence of interference resistance of the following
connection:
–86D between components 120 and 675.
–Make sure that the earth is in order on connection M of component 675.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
"ACTIVE"Check the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch, check the insulation between connections M and
86D of component 675, with the switch in the rest position.
–Repeat this operation with the switch engaged, and check the continuity between
the two connections.
If these 2 checks are faulty, replace the switch.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

17B-230V7 MR-413-X44-17B000$152.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
SIM 32 Injection
Program no.: D3
Vdiag No.: 44, 4C, 50
and 54
ET415
CONTINUED 2
WITHOUTThis status is present on the diagnostic tool when:
The computer has been reinitialised,
The computer has been reprogrammed.
STATUS 1 Traction control request
If the vehicle is fitted with a traction control system, the cruise control function is
deactivated every time the ABS computer calls for traction control.
Status ET415 becomes STATUS 1 when driving with the cruise control active
(ET042 Cruise control/Speed limiter: CRUISE CONTROL) and when traction
control is requested.
This deactivates cruise control.
Reinitialise status ET415 of the injection computer by applying command
RZ001 Fault memory.
If status ET415 becomes STATUS 1 with no traction control request (see 38C, Anti-
lock braking system).
STATUS 2 Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2, when the vehicle is being driven, with cruise
control active (ET042) and the brake pedal depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command
RZ001.
If status ET415 becomes STATUS 2 without pressing the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact No. 1 and No. 2.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.