ignition RENAULT TWINGO RS 2009 2.G Electrical Equipment - Radio R01-08 User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 91, PDF Size: 0.53 MB
Page 38 of 91
86A-38
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF030
PRESENT
OR
STOREDCOMPUTER CONFIGURATION
1.DEF: Blank or incomplete configuration
NOTESSwitch on the radio.
Configure the system (see Configuration and programming).
After configuration, switch off the ignition for 5 seconds then switch the ignition back on again.
If the fault persists, contact your Techline.
R108_VA4_DF030
Page 40 of 91
86A-40
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF039
PRESENT
OR
STOREDBATTERY VOLTAGE
1.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
– The + after ignition feed is activated,
– The multimedia system is switched on using the on/off button.
– The battery voltage is out of range (12 V < X < 15 V).
Note:
Apply this fault finding method if the fault reappears as present after having been
cleared
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the conformity of the fuse in the fuse and relay box:
•for New Twingo: F48 (15A),
•for Clio III: F2 (20A) and Unit fuse 710 (15A).
Replace the fuse if not correct.
Disconnect the connector of the radio 261.
Check the continuity of the earth on connection MAO (New Twingo) or MT (Clio III).
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the +12 V supply on connection BCP4 of component 261.
If the supply is not correct, check the insulation, continuity and absence of interference resistance on
connection code BCP4 between components 260 and 261.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R108_VA4_DF039
Page 43 of 91
86A-43
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF055
PRESENT
OR
STOREDBUTTON JAMMED
1.DEF: Radio front panel button jammed.
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The + after ignition feed is activated,
–The multimedia system is switched on using the on/off button.
The button concerned is pressed for at least 2 minutes,
Check the conformity of the radio buttons by consulting the following statuses:
–ET005 Source button,
–ET007 Info traffic button,
–ET008 Radio on/off button,
–ET009 CD eject button,
–ET010 Radio preset button 1,
–ET011 Radio preset button 2,
–ET012 Radio preset button 3,
–ET013 Radio preset button 4,
–ET014 Radio preset button 5,
–ET015 Radio preset button 6,
–ET063 MEM button,
–ET068 Volume - button,
–ET069 Volume + button,
–ET070 OK button,
–ET071 Up button,
–ET072 Down button,
–ET073 Left-hand button,
–ET074 Right-hand button,
If the one of the statuses is Pressed, press on the corresponding button so that the status becomes Released.
If the fault is still present, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
R108_VA4_DF055
Page 46 of 91
86A-46
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory, after pressing the ON/
OFF button.
Deal with any other faults.
V2 MR-413-X44-86A100$120.mif
RADIO
Fault finding – Interpretation of faults86A
R01-08
Vdiag No.: A4
DF064
PRESENT
OR
STOREDACTIVATION SIGNAL
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a navigation system, use the multimedia connection unit
computer, component code 1714, for fault finding.
For a vehicle without a navigation system, use the display computer, component code
653, for fault finding.
Check the condition of the connector on the radio, component code 261, and, depending on the equipment level,
on the display, component code 653, or on the multimedia connection unit, component code 1714.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34HY between,components 261 and 653 or 1714,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection is correct, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.
R108_VA4_DF064
Page 49 of 91
86A-49V2 MR-413-X44-86A100$130.mif
86A
R01-08
Vdiag No.: A4
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
SupplyPR011:Battery
voltage12 V < X < 15 VIn the event of an
inconsistency, consult the
interpretation of fault DF039
Battery voltage.
R108_VA4_CCONF
RADIO
Fault finding – Conformity check
Page 50 of 91
86A-50V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Front panel buttonET010:Radio preset
button 1PRESSED RELEASEDIn the event of an
inconsistency, consult the
interpretation of fault DF055
Button jammed.
ET011:Radio preset
button 2PRESSED RELEASED
ET012:Radio preset
button 3PRESSED RELEASED
ET013:Radio preset
button 4PRESSED RELEASED
ET014:Radio preset
button 5PRESSED RELEASED
ET015:Radio preset
button 6PRESSED RELEASED
ET008:Radio on/off
buttonPRESSED RELEASED
ET009:CD eject buttonPRESSED RELEASED
Page 51 of 91
86A-51V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION (continued)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Front panel button
(continued)ET071:Up buttonPRESSED RELEASEDIn the event of an
inconsistency, consult the
interpretation of fault DF055
Button jammed.
ET072:Down buttonPRESSED RELEASED
ET070:"OK" buttonPRESSED RELEASED
ET069:Volume "-" buttonPRESSED RELEASED
ET068:Volume "+" buttonPRESSED RELEASED
Page 52 of 91
86A-52V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
SUB-FUNCTION: USER SELECTION (continued)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Front panel button
(continued)ET063:"MEM" buttonPRESSED RELEASED
In the event of an
inconsistency, consult the
interpretation of fault DF055
Button jammed. ET005:Source buttonPRESSED RELEASED
ET007:Traffic info buttonPRESSED RELEASED
ET073:Left-hand buttonPRESSED RELEASED
ET074:Right-hand buttonPRESSED RELEASED
CD ejectionAC013:CD ejectionThis command is used for
testing CD ejection from
the CD player.In the event of an
inconsistency, contact the
Techline.
SupplyPR011:Battery voltage12 V < X < 15 VIn the event of an
inconsistency, consult the
interpretation of fault DF039
Battery voltage.
Computer
activationET065:Activation requestACTIVE INACTIVE
In the event of an
inconsistency, consult the
interpretation of fault DF064
Activation signal.
ET057:Activation signalACTIVE INACTIVE
Page 53 of 91
86A-53V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
SUB-FUNCTION: AUDIO
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Audio testAC004:Test right front
speaker line
This command is used to
successively activate
each speaker.In the event of an
inconsistency, consult the
interpretation of fault DF001
Front right-hand speaker.
AC005:Test left front
speaker lineIn the event of an
inconsistency, consult the
interpretation of fault DF002
Front left-hand speaker.
AC006:Test right rear
speaker lineIn the event of an
inconsistency, consult the
interpretation of fault DF003
Rear right-hand speaker.
AC007:Test left rear
speaker lineIn the event of an
inconsistency, consult the
interpretation of fault DF004
Rear left-hand speaker.
Page 54 of 91
86A-54V2 MR-413-X44-86A100$130.mif
RADIO
Fault finding – Conformity check86A
R01-08
Vdiag No.: A4
FUNCTION: MULTIMEDIA
FUNCTION: WIRELESS COMMUNICATIONS
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Radio
receptionPR005:Radio
field
intensity0 dBµV
interpretation of parameter
PR005.