diagram RENAULT TWINGO RS 2009 2.G Electrical Equipment - Radio R2-08 User Guide

86A-40
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF023
PRESENT
OR
STOREDCD CHANGER
1.DEF: Internal electronic fault
NOTESAn ACB (Audio Connection Unit) can also be connected in place of the CD changer.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check for a CD changer in the vehicle.
Check the consistency between the configuration of the radio and the vehicle equipment by reading configuration
LC005 External components and correct it, if necessary, using SC002 Computer configuration
(see Configuration and programming).
If the vehicle is equipped with a CD changer, it was fitted as an accessory. Please refer to the handbook delivered
with the product.
If the fault is still present, replace the CD changer.
R208_V64_DF023

86A-41
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF025
PRESENT
OR
STOREDCD CHANGER READING
1.DEF: Disc cannot be read
NOTESUse the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check for a CD changer in the vehicle.
Check the consistency between the configuration of the radio and the vehicle equipment by reading configuration
LC005 External components and correct it, if necessary, using SC002 Computer configuration
(see Configuration and programming).
If the vehicle is equipped with a CD changer, it was fitted as an accessory. Please refer to the handbook delivered
with the product.
If the fault is still present, replace the CD changer.
R208_V64_DF025

86A-49
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF039
PRESENT
OR
STOREDBATTERY VOLTAGE
1.DEF: Excess voltage
2.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
– The + after ignition feed is activated,
– The multimedia system is switched on using the on/off button.
– The battery voltage is out of range (12 V < battery voltage < 15 V).
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the conformity of the fuse in the fuse and relay box:
–for New Twingo: F48 (15A),
–for Clio III: F2 (20A) and Unit fuse 710 (15A).
Replace the fuse if not correct.
Disconnect the connector of the radio 261.
Check the continuity of the earth on connection MAO (New Twingo) or MT (Clio III).
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the +12 V supply on connection BCP4 of component 261.
If the supply is not correct, check the insulation, continuity and absence of interference resistance on
connection code BCP4 between components 260 and 261.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R208_V64_DF039

86A-50
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF040
DF043
PRESENT
OR
STOREDNO AUDIO CD CHANGER SIGNALS
1.DEF: No communication with the CD changer
NOTESAn ACB (Audio Connection Unit) can also be connected in place of the CD changer.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Check for a CD changer in the vehicle.
Check the consistency between the configuration of the radio and the vehicle equipment by reading configuration
LC005 External components and correct it, if necessary, using SC002 Computer configuration
(see Configuration and programming).
Look for any signs of damage to the wiring harness, check the condition and connection of the connectors and
connections of components 261 and the CD changer.
If the connectors or connections are faulty and if there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector or the wiring, otherwise replace
the wiring.
If the vehicle is equipped with a CD changer, it was fitted as an accessory. Please refer to the handbook delivered
with the product.
If the checks are correct, replace the CD changer.
If the fault persists, contact your Techline.
R208_V64_DF040/R208_V64_DF043

86A-52
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF051
PRESENT
OR
STOREDFRONT RIGHT-HAND TWEETER
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The multimedia system was switched on using the on/off button for at least
10 seconds,
–Command AC004 Front right-hand speakers line test was run.
Check the speaker first when dealing with several faults.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Run command SC002 Computer configuration (see Configuration) and configure the equipment.
Check the condition and connection of the connectors of radio 261, of the front right-hand tweeter connector
365, of the front right-hand speaker connector 1598 (left-hand drive) or 1597 (right-hand drive) (bent or broken
tabs, etc.).
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation and absence of interference resistance on the following connections:
•34E between components 261 and 365, 1598 (left-hand drive) or 1597 (right-hand drive),
•34F between components 261 and 365, 1598 (left-hand drive) or 1597 (right-hand drive).
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace component 365 (see MR 392 (Clio III) or MR 411 (New Twingo)
Mechanical, 86A, Radio, Tweeter: Removal - Refitting).
If the fault persists, contact your Techline.
R208_V64_DF051

86A-53
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF052
PRESENT
OR
STOREDFRONT LEFT-HAND TWEETER
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The multimedia system was switched on using the on/off button for at least
10 seconds,
–Command AC005 Front left-hand speaker line test was run.
Check the speaker first when dealing with several faults.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Run command SC002 Computer configuration and configure the equipment.
Check the condition and connection of the connectors of radio 261, of the front left-hand tweeter connector 366
and of the front left-hand speaker connector 1597 (left-hand drive) or 1598 (right-hand drive) (bent or broken tabs,
etc.).
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation and absence of interference resistance on the following connections:
•34G between components 261 and 366, 1597 (left-hand drive) or 1598 (right-hand drive),
•34H between components 261 and 366, 1597 (left-hand drive) or 1598 (right-hand drive).
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connections are correct, replace component 366 (see MR 392 (Clio III) or MR 411 (New Twingo)
Mechanical, 86A, Radio, Tweeter: Removal - Refitting).
If the fault persists, contact your Techline.
R208_V64_DF052

86A-54
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF053
PRESENT
OR
STOREDREAR RIGHT-HAND TWEETER
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The multimedia system was switched on using the on/off button for at least
10 seconds,
–Command AC006 Rear right-hand speaker line test was run,
–The fault can only be detected if the battery voltage is between:
12 V < X < 15 V.
Note:
The rear tweeters are integrated into the rear speakers and are only available on
New Twingo.
Use the Wiring Diagrams Technical Note for New Twingo.
Check the condition and connection of the connectors of radio 261, of the rear right-hand speaker 189 (bent or
broken tabs, etc.).
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the connector of component 189 (see MR 411 (New Twingo) Mechanical, 86A, Radio, Rear speaker:
Removal - Refitting).
Measure the resistance of component 189 using a multimeter, with the ignition off.
If the resistance is not between: 3.5 Ω < X < 4.5 Ω, replace component 189 (see MR 411 (New Twingo)
Mechanical, 86A, Radio, Rear speaker: Removal - Refitting).
Check the continuity, insulation and absence of interference resistance on the following connections:
•34D between components 261 and 189,
•34C between components 261 and 189.
If the connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R208_V64_DF053

86A-55
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF054
PRESENT
OR
STOREDREAR LEFT-HAND TWEETER
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The multimedia system was switched on using the on/off button for at least
10 seconds,
–Command AC007 Rear left-hand speaker line test was run,
–The fault can only be detected if the battery voltage is between:
12 V < X < 15 V.
Note:
The rear tweeters are integrated into the rear speakers and are only available on
New Twingo.
Use the Wiring Diagrams Technical Note for New Twingo.
Check the condition and connection of the connectors of radio 261 and of the rear left-hand speaker 190 (bent or
broken tabs, etc.).
If any of the connectors are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Disconnect the connector of component 190 (see MR 411 (New Twingo) Mechanical, 86A, Radio, Rear speaker:
Removal - Refitting).
Measure the resistance of component 190 using a multimeter, with the ignition off.
If the resistance is not between: 3.5 Ω < X < 4.5 Ω, replace component 190 (see MR 411 (New Twingo)
Mechanical, 86A, Radio, Rear speaker: Removal - Refitting).
Check the continuity, insulation and absence of interference resistance on the following connections:
•34A between components 261 and 190,
•34B between components 261 and 190.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault persists, contact your Techline.
R208_V64_DF054

86A-58
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF056
PRESENT
OR
STOREDMICROPHONE
CC.0: Short circuit to earth
CO: Open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button,
–the "hands-free" function has been activated,
–the command AC010 Microphone test was run.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Look for any damage to the wiring harness and check the condition and connection of the connectors for
components 261 and 789.
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Run command AC010 Microphone Test and check that the microphone, component code 789 is correctly
supplied between connections 107G and 107J.
Check the continuity, insulation and absence of interference resistance on the following connections:
•107F between components 261 and 789,
•107G between components 261 and 789,
•107J between components 261 and 789,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the microphone (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical,
86B, Car phone, "Hands-free" microphone: Removal - Refitting).
R208_V64_DF056

86A-59
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ003 Fault memory, after pressing the ON/
OFF button.
Deal with any other faults.
V1 MR-413-X44-86A150$120.mif
RADIO
Fault finding – Interpretation of faults86A
R2-08
Vdiag No.: 64
DF064
PRESENT
OR
STOREDACTIVATION SIGNAL
CC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–the + after ignition feed is activated,
–the multimedia system has been switched on using the on/off button.
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
For a vehicle equipped with a navigation system, use the multimedia connection unit
computer, component code 1714, for fault finding.
For a vehicle without a navigation system, use the display computer, component code
653, for fault finding.
Check the condition of the connector on the radio, component code 261, and, depending on the equipment level,
on the display, component code 653, or on the multimedia connection unit, component code 1714.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
•34HY between,components 261 and 653 or 1714,
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the connection is correct, replace the radio (see MR 392 (Clio III) or MR 411 (New Twingo) Mechanical, 86A,
Radio, Radio: Removal - Refitting).
If the fault persists, contact your Techline.
R208_V64_DF064