ECO mode RENAULT TWINGO RS 2009 2.G Electrical Equipment - Radio Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 42, PDF Size: 0.29 MB
Page 1 of 42
Electrical equipment
"The repair procedures given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The procedures may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from
which his vehicles are constructed."
V1
All rights reserved by Renault s.a.s.
Edition Anglaise
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault s.a.s.
© Renault s.a.s.
V1 MR-413-X44-86A000$000_engTOC.mif
RADIO
List and location of components 86A - 2
Operating diagram 86A - 3
Function86A - 4
Role of components 86A - 5
Defect and safe modes 86A - 6
General Information 86A - 7
Security code recovery procedure 86A - 8
Anti-theft code86A - 9
Configuration - Settings 86A - 12
Connections86A - 13
Self-test procedure 86A - 14
Radio fault finding: Customer complaints 86A - 15
Fault finding chart 86A - 16
Radio control satellite: Check 86A - 36
Recovering a jammed CD 86A - 37
86A
MR-413-X44-86A000$000_engTOC.mif
Page 9 of 42
86A-9
MR-413-X44-86A000$504_eng.mif
V1
86A
RADIO
Anti-theft code
The radio is protected by a four digit code. This code must be entered via the control satellite or the radio keypad
each time the battery is disconnected.
Entering the code with the control on the steering wheel:
Press the lower button on the control to confirm an entry.
Entering the code using the radio:
Enter the digits using buttons 1, 2, 3 and 4, and then confirm with button 6.
If the code is entered incorrectly, the radio will be locked (1 minute for the first error, 2 minutes for the second error,
4 minutes for the third error, etc. 32 minutes maximum).
Some configurations must be programmed after the code has been entered for the first time (see configuration -
settings). These settings are stored when the battery is disconnected.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered (with
regular warning bleeps).
If the vehicle is equipped with a CD changer in the front panel, a code is exchanged between the CD changer and
the radio.
–If a new CD changer is fitted, the radio code is programmed when the battery or CD changer is connected.
–If the radio is replaced, enter the security code of the old radio connected to the CD changer. The CD changer is
programmed with the code for the new radio.
–If the old radio code is lost, the changer code can be cleared using the clearing code. The clearing code is sent by
the Techline.
Note:
If there is a configuration error, you can return to scrambled mode by pressing the 2 and 5 buttons at the same
time as switching the power on. Then wait 2 minutes.
Note:
The CD changer is supplied uncoded. When it is installed in the vehicle, the CD changer is programmed with the
radio supply code.
Reminder:
The radio will operate for approximately 2 minutes in scrambled mode without the code having been entered
(with regular warning bleeps).
MR-413-X44-86A000$504_eng.mif
Page 10 of 42
86A-10
MR-413-X44-86A000$504_eng.mif
V1
RADIO
Anti-theft code86A
THE DISPLAY SHOWS “CODE” OR “0000”
Entering the security code. The radio bleeps
every 2 seconds for 2 minutes then displays
CODE.
Is the radio code known?
YES
The radio displays “CODE” then “0000”.
YES
Enter the first digit using the wheel control on the steering wheel or the front panel.
Confirm that the digit is correct by briefly pressing the lower steering wheel button or front panel button.
Use the same procedure to enter the remaining three digits.
Confirm the security code by pressing and holding the same button or button (6) on the front panel.
Does the radio display “ERROR” then “CODE”.
YES NO
(See anti-theft code recovery procedure)
NOHas the 4-digit code been obtained?
YES NO
NOGo back to scrambled mode. With the radio off,
press the 2, 5 and ON buttons. Wait
approximately 2 minutes until “CODE” then
“0000”.appears
NODoes the radio display “CD ERROR” then “CD
CODE”.?
YES
See display shows CD CODE.
The radio switches to CONFIGURATION mode
(if being used for the first time) and operates
normally.
Page 12 of 42
86A-12
MR-413-X44-86A000$567_eng.mif
V1
86A
RADIO
Configuration - Settings
CONFIGURATIONS
NOTE:
To select the zone in which the Tuner is to be used, press buttons 2 and 5 simultaneously while turning the power on.
Then wait approximately 2 minutes. Enter the four digit code and then:
●select the relevant zone:
–America
–Japan
–Asia
–Arabia
–Others (Europe, Africa, other)
SETTINGS
To switch to setting mode (Expert mode), press and hold (4 seconds) the source (SRC) button until you hear a
bleep. This allows you to adjust the following functions:
NR range:
●AF mode activation (automatic retuning),
●vehicle speed-dependent volume control (5 for maximum regulation, 0 to disable regulation),
●Loudness mode activation.
PN range:
●AF mode activation (automatic retuning),
●vehicle speed-dependent volume control (5 for maximum regulation, 0 to disable regulation),
●Loudness mode activation,
●Assisted tuner mode activation,
●configuration of the number of speakers (2 or 4),
●manual or dynamic list selection.
PN6 radio:
●AF mode activation (automatic retuning),
●vehicle speed-dependent volume control (5 for maximum regulation, 0 to disable regulation),
●Loudness mode activation,
●Assisted tuner mode activation,
●configuration of the number of speakers (2 or 4),
●manual or dynamic list selection.
●activation of data storage in accordance with the RENAULT Card: CARD ON/OFF. To operate, the radio must be
accompanied by the navigation system. Note:
These configurations are not required when the secret code is entered after the power supply has been cut.
MR-413-X44-86A000$567_eng.mif
Page 16 of 42
86A-16
MR-413-X44-86A000$819_eng.mif
V1
86A
ALP 1 The radio bleeps approximately every 2 seconds
The radio bleeps every 2 seconds
wait 2 minutes.
Enter the radio's unique security code.
Is the code correct?
YES
The 'radio switches to Configuration mode
(if being used for the first time) and operates
normally.
See anti-theft code, the radio displays “CODE”
then “0000”.
RADIO
Fault finding chart
NOThe radio displays CODE, then 0000. Check
the code and try again.
Has it been entered correctly?
MR-413-X44-86A000$819_eng.mif
YES
NO
Page 28 of 42
86A-28
MR-413-X44-86A000$819_eng.mif
V1
RADIO
Fault finding chart86A
ALP 6 Radio reception faults
Poor radio reception.
Does the radio "scan"the stations in FM mode?
NO
Does the sound cut out for < than 1 second from
time to time in FM mode?
Does the radio crackle?
NO YES
The vehicle is in an area of poor reception.
YESFault external to the radio (transmitter
synchronisation).
YESThe vehicle is in an area of poor reception.
The radio takes longer to find an adequate
transmitter.
Disable AF in Expert mode.
With the vehicle outside and in an area with
good reception, test the reception level in the
radio's fault finding menu.
A
Page 34 of 42
86A-34
MR-413-X44-86A000$819_eng.mif
V1
RADIO
Fault finding chart86A
ALP 10 The radio does not receive all stations
The radio works but does not receive all stations.
Check that the radio tuner is configured in the
others mode.
Is the tuner configured in the others mode?
YES
Does the radio still not receive all stations?
NO
The fault has been rectified.
NOReconfigure the radio tuner.
YESSee ALP 6.