fuse RENAULT TWINGO RS 2009 2.G Electrical Equipment User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 241
Page 140 of 241
88A-4
WIRING HARNESS
Front left-hand wiring: Removal - Refitting
LEFT-HAND DRIVE
88A
-the cover to the engine compartment connection
unit.
II - REMOVAL OPERATION FOR PART
CONCERNED
a
aDisconnect the front left-hand wiring/engine harness
connector (3) .
aRemove:
-the fuses (4) ,
-the engine compartment connection unit supply wi-
ring nut (5) .aUnclip:
-the front left-hand wiring/engine harness connector
(6) ,
-the fuse holders (7) .
aRemove the engine compartment connection unit
nuts (8) . WARNING
To prevent any risk of noise, premature wear,
short circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.
121213
121214
121215
Page 144 of 241
88A-8
WIRING HARNESS
Front left-hand wiring: Removal - Refitting
LEFT-HAND DRIVE
88A
-the front left-hand indicator connector,
-the front left-hand headlight connector,
-the front left-hand side light connector,
-the windscreen washer pump connector,
-the horn connector,
-the front right-hand side light connector,
-the front right-hand headlight connector,
-the front right-hand indicator connector.
aConnect the regulated additional heater connector.
aRefit the additional heater earth wiring nut.
aConnect the gearbox pump assembly relay connec-
tor.
aRefit:
-the windscreen wiper mechanism (see 85A, Wi-
ping - Washing, Windscreen wiper mechanism:
Removal - Refitting, page 85A-10) ,
-the earth wiring nut on the bodywork,
-the earth wiring nut on the negative battery termi-
nal,
-the hydraulic brake unit earth wiring nut,
-the earth wiring nut on the body,
-the earth wiring nut on the front left-hand side
member,
-the earth wiring nut on the front right-hand side
member,
aClip:
-the section of wiring onto the dashboard cross
member,
-the section of wiring onto the windscreen washer
reservoir
-the section of wiring onto the front bumper cross
member,
-the section of wiring onto the bulkhead.
aRefit the engine compartment connection unit nuts.aClip on:
-the fuse holders,
-the front left-hand wiring/engine harness connec-
tor.
aConnect the front left-hand wiring/engine harness
connector.
aRefit:
-the engine compartment connection unit supply wi-
ring nut,
-the fuses.
aClip on the engine compartment connection unit
board.
III - FINAL OPERATION
aRefit:
-the cover from the engine compartment connection
unit,
-the bolts.
aConnect the cruise control switch connector.
aRefit the dashboard lower trim.
aClip the glovebox in position.
aRefit:
-the left-hand suspended engine mounting (see
Left-hand suspended engine mounting: Remo-
val - Refitting) (MR 411, 19D, Engine mounting),
-the brake servo (see Brake servo: Removal - Re-
fitting) (MR 411, 37A, Mechanical component con-
trols),
-the master cylinder (see Master cylinder: Remo-
val - Refitting) (MR 411, 37A, Mechanical compo-
nent controls),
-the side indicators (see 80B, Headlights, Side in-
dicator: Removal - Refitting, page 80B-13) ,
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection), CLIMATE CONTROL
JH1
WARNING
To prevent damage to the wiring har ness when
refitting, obser ve the original routing.
CRUISE CONTROL
Page 154 of 241
88A-18
WIRING HARNESS
Engine wiring: Removal - Refitting
K9K
88A
-the connector from the water detection sensor on
the fuel filter (4) ,
-the camshaft position sensor connector (5) ,
-the pinking sensor connector (6) ,
-the turbocharging pressure sensor connector (7) ,
-the air temperature sensor connector (8) ,
-the injector connector (9) ,
-the heater plugs connector (10) ,
-the fuel temperature sensor connector (11) ,
-the fuel rail pressure sensor connector (12) ,
-the diesel injection computer connectors (13) ,
-the pre-postheating unit connector (14) ,
-the exhaust gas recirculation solenoid valve con-
nector (15) ,
-the coolant temperature sensor connector (16) ,
-the crankshaft position sensor connector (17) ,
-the reversing lights switch connector (18) ,
-the front of engine wiring/engine harness connec-
tor (19) .
aDisconnect the cooling fan assembly connector (20)
.aDisconnect:
-the engine cooling fan assembly connector (21) ,
-the engine cooling fan assembly resistor connector
(22) ,
-the refrigerant fluid pressure sensor connector (23)
,
-the air conditioning compressor connector (24) .
aRemove:
-the alternator earth wiring nut (25) ,
-the nuts from the starter supply and earth terminals
(26) ,
-the engine earth wiring nut (27) ,
-the positive battery terminal wiring nut (28) ,
-the earth wiring nut on the front left-hand side
member (29) ,
-the battery protection fuse wiring nuts (30) ,
-the wiring mounting nut on the battery protection
fuse board (31) ,
-the engine compartment connection unit supply wi-
ring nut (32) .
aUnclip:
-the section of wiring on the cylinder head, STANDARD HEATING
122359
AIR CONDITIONING
125249
Page 155 of 241
88A-19
WIRING HARNESS
Engine wiring: Removal - Refitting
K9K
88A
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRemove the engine harness.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine harness.
aConnect the engine cooling fan assembly connector.
aConnect:
-the air conditioning compressor connector,
-the refrigerant fluid pressure sensor connector,
-the engine cooling fan assembly resistor connec-
tor,
-the engine cooling fan assembly connector.
aConnect:
-the engine harness/front of engine wiring connec-
tor,
-the reversing lights switch connector,
-the crankshaft position sensor connector,
-the coolant temperature sensor connector,
-the air inlet temperature sensor connector,-the exhaust gas recirculation solenoid valve con-
nector,
-the connector to the pre-postheating unit,
-the diesel injection computer connectors,
-the fuel rail pressure sensor connector,
-the fuel temperature sensor connector,
-the heater plugs connector,
-the injector connectors,
-the air temperature sensor connector,
-the turbocharging pressure sensor connector,
-the pinking sensor connector,
-the camshaft position sensor connector,
-the connector from the water detection sensor on
the fuel filter,
-the alternator connector,
-the oil pressure sensor connector.
aRefit:
-the engine compartment connection unit supply wi-
ring nut,
-the wiring mounting nut on the battery protection
fuse board,
-the battery protection fuse wiring nuts,
-the earth wiring nut on the front left-hand side
member,
-the positive battery terminal wiring nut,
-the engine earth wiring nut,
-the starter supply and earth terminal nuts,
-the alternator earth wiring nut.
aClip:
-the section of wiring on the cylinder head,
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
III - FINAL OPERATION.
aRefit:
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture), WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
STANDARD HEATING
AIR CONDITIONING
Page 159 of 241
88A-23
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F, and 780
88A
-the oil vapour recirculation hose reheater connec-
tor (5) ,
-the engine harness/injection wiring connector (6) ,
-the coolant temperature sensor connector (7) ,
-the crankshaft position sensor connector (8) ,
-the oil pressure sensor connector (9) ,
-the alternator connector (10) ,
-the pinking sensor connector (11) ,
-the air temperature sensor connector (12) ,
-the turbocharger pressure sensor connector (13) ,
-the motorised throttle valve connector (14) ,
-the ignition coil connector (15) ,
-the turbocharger solenoid valve connector (16) ,
-the downstream oxygen sensor connector (17) ,
-the reversing lights switch connector (18) ,
-the petrol injection computer connectors (19) ,
-the engine harness/front of engine wiring connec-
tor (20) .
aDisconnect the cooling fan assembly connector (21)
.aDisconnect:
-the engine cooling fan assembly connector (22) ,
-the engine cooling fan assembly resistor connector
(23) .
-the refrigerant fluid pressure sensor connector (24)
,
-the air conditioning compressor connector (25) ,
aRemove:
-the alternator earth wiring nut (26) ,
-the nuts from the starter supply and earth terminals
(27) ,
-the earth wiring nuts on the engine (28) ,
-the earth wiring nut on the front left-hand side
member (29) ,
-the positive battery terminal wiring nut (30) ,
-the negative battery terminal wiring nuts (31) ,
-the wiring mounting nut on the battery protection
fuse board (33) ,
-the engine compartment connection unit supply
terminal nut (32) .
aUnclip:
-the section of wiring on the cylinder head, STANDARD HEATING
122359
AIR CONDITIONING
125249
Page 160 of 241
88A-24
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F, and 780
88A
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRemove the engine harness.
REFITTING
I - REFITTING PREPARATION OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine harness.
aConnect the engine cooling fan assembly connector.
aConnect:
-the air conditioning compressor connector,
-the refrigerant fluid pressure sensor connector,
-the engine cooling fan assembly connector,
-the engine cooling fan assembly resistor connec-
tor.
aConnect:
-the engine harness/front of engine wiring connec-
tor,
-the connectors to the petrol injection computer,
-the reversing lights switch connector,
-the downstream oxygen sensor connector,
-the turbocharger solenoid valve connector,-the ignition coil connector,
-the motorised throttle valve connector,
-the turbocharger pressure sensor connector,
-the air temperature sensor connector,
-the pinking sensor connector,
-the alternator connector,
-the oil pressure sensor connector,
-the crankshaft position sensor connector,
-the coolant temperature sensor connector,
-the engine harness/injection wiring connector,
-the oil vapour recirculation hose reheater connec-
tor,
-the air inlet pressure sensor connector,
-upstream oxygen sensor connector,
-the fuel vapour absorber connector.
aRefit:
-the engine compartment connection unit supply
terminal nut,
-the wiring mounting nut on the battery protection
fuse board,
-the negative battery terminal wiring nuts,
-the positive battery terminal wiring nut,
-the earth wiring nut on the front left-hand side
member,
-the earth wiring nuts on the engine,
-the starter wiring nuts,
-the alternator earth wiring nut.
aClip:
-the section of wiring on the cylinder head,
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
III - FINAL OPERATION.
aRefit:
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) , WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
STANDARD HEATING
AIR CONDITIONING
Page 164 of 241
88A-28
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F or D7F
88A
-the fuel vapour absorber connector (3) ,
-the ignition coil connector (4) ,
-the upstream oxygen sensor connector (5) ,
-the downstream oxygen sensor connector (6) ,
-the reversing lights switch connector (7) ,
-the radio interference suppressor connector (8) ,
-the alternator connector (11) ,
-the engine harness/injection wiring connector (12) ,
-the air inlet temperature sensor connector (13) ,
-the pinking sensor connector (14) ,
-the air inlet pressure sensor connector (15) ,
-the motorised throttle valve connector (16) ,
-the coolant temperature sensor connector (17) ,
-the crankshaft position sensor connector (18)
-the petrol injection computer connectors (19) ,
-the engine harness/front of engine wiring connec-
tor (20) .
aDisconnect the cooling fan assembly connector (21)
.aDisconnect:
-the engine cooling fan assembly connector (22) ,
-the engine cooling fan assembly resistor connector
(23) ,
-the refrigerant fluid pressure sensor connector (9) ,
-the air conditioning compressor connector (10) .
aRemove:
-the alternator earth wiring nut (24) ,
-the nuts from the starter supply and earth terminals
(25) ,
-the engine earth wiring nuts (26) ,
-the earth wiring nut on the front left-hand side
member (27) ,
-the positive battery terminal wiring nut (28) ,
-the negative battery terminal wiring nuts (29) ,
-the wiring mounting nut on the battery protection
fuse board (30) ,
-the engine compartment connection unit supply
terminal nut (31) .
aUnclip:
-the section of wiring on the cylinder head, STANDARD HEATING
122359
AIR CONDITIONING
125249
Page 168 of 241
88A-32
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F or D7F
88A
aDisconnect:
-the sequential gearbox computer connectors (53) ,-the engine harness/sequential gearbox wiring con-
nector (54) .
aRemove:
-the alternator earth wiring nut (55) ,
-the nuts from the starter supply and earth terminals
(56) ,
-the engine earth wiring nuts (57) ,
-the earth wiring nut on the front left-hand side
member (58) ,
-the positive battery terminal wiring nut (59) ,
-the negative battery terminal wiring nuts (60) ,
-the wiring mounting nut on the battery protection
fuse board (61) ,
-the engine compartment connection unit supply wi-
ring nut (62) .
aUnclip:
-the section of wiring on the cylinder head, JH1
125270
125271
Page 169 of 241
88A-33
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F or D7F
88A
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRemove the engine harness.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine harness.
aConnect the engine cooling fan assembly connector.
aConnect:
-the engine cooling fan assembly connector,
-the engine cooling fan assembly resistor connec-
tor,
-the air conditioning compressor connector,
-the refrigerant fluid pressure sensor connector.
aConnect:
-the engine harness/front of engine wiring connec-
tor,-the connectors to the petrol injection computer,
-the crankshaft position sensor connector,
-the coolant temperature sensor connector,
-the motorised throttle valve connector,
-the air inlet pressure sensor connector,
-the pinking sensor connector,
-the air inlet temperature sensor connector,
-the engine harness/injection wiring connector,
-the alternator connector,
-the radio interference suppressor connector,
-the reversing lights switch connector,
-the downstream oxygen sensor connector,
-upstream oxygen sensor connector,
-the ignition coil connector,
-the fuel vapour absorber connector,
-the oil pressure sensor connector.
aRefit:
-the engine compartment connection unit supply
terminal nut,
-the wiring mounting nut on the battery protection
fuse board,
-the negative battery terminal wiring nuts,
-the positive battery terminal wiring nut,
-the earth wiring nut on the front left-hand side
member,
-the earth wiring nuts on the engine,
-the starter wiring nuts,
-the alternator earth wiring nut.
aClip:
-the section of wiring on the cylinder head,
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRefit the engine harness. WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
D7F
STANDARD HEATING
AIR CONDITIONING
D4F
Page 170 of 241
88A-34
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F or D7F
88A
aConnect:
-the engine harness/sequential gearbox wiring con-
nector,
-the sequential gearbox computer connectors.
aConnect the engine cooling fan assembly connector.
aConnect:
-the engine cooling fan assembly connector,
-the engine cooling fan assembly resistor connec-
tor,
-the air conditioning compressor connector,
-the refrigerant fluid pressure sensor connector.aConnect:
-the engine harness/front of engine wiring connec-
tor,
-the connectors to the petrol injection computer,
-the coolant temperature sensor connector,
-the crankshaft position sensor connector,
-the engine harness/injection wiring connector,
-the pinking sensor connector,
-the alternator connector,
-the motorised throttle valve connector,
-the reverse gear switch connector,
-upstream oxygen sensor connector,
-the downstream oxygen sensor connector,
-the oil pressure sensor connector,
-the radio interference suppressor connector,
-the ignition coil connector,
-the fuel vapour absorber connector,
-the air inlet pressure sensor connector.
aRefit:
-the engine compartment connection unit supply
terminal nut,
-the wiring mounting nut on the battery protection
fuse board,
-the negative battery terminal wiring nuts,
-the positive battery terminal wiring nut,
-the earth wiring nut on the front left-hand side
member,
-the earth wiring nuts on the engine,
-the starter wiring nuts,
-the alternator earth wiring nut.
aClip:
-the section of wiring on the cylinder head,
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly. JH1
STANDARD HEATING
AIR CONDITIONING