remote control RENAULT TWINGO RS 2009 2.G Electrical Equipment Workshop Manual

Contents
82A ENGINE IMMOBILISER
Immobiliser system: List and
location of components 82A-1
Ignition switch: Removal -
Refitting 82A-3
Transponder ring: Removal -
Refitting 82A-6
Battery for remote door
locking control: Removal -
Refitting 82A-8
82B HORN
Audible warning: Removal -
Refitting 82B-1
83A INSTRUMENT PANEL
Instr ument panel: Removal -
Refitting 83A-1
Rev counter: Removal -
Refitting 83A-3
83D CRUISE CONTROL
Cruise control - speed
limiter: List and location of
components 83D-1
Switch: Removal - Refitting 83D-2
Steering wheel switch:
Removal - Refitting 83D-384A CONTROL - SIGNALS
Steering column switch
assembly: List and location
of components 84A-1
Steering column switch
assembly: Removal -
Refitting 84A-2
Screen wiper switch:
Removal - Refitting 84A-6
Signals and lighting switch:
Removal - Refitting 84A-8
Hazard warning lights and
central door control:
Removal - Refitting 84A-10
Lighting dimmer: Removal -
Refitting 84A-12
Exter ior rear view mirror
control switch: Removal -
Refitting 84A-13
Heated rear screen: Repair 84A-14
85A WIPING - WASHING
Wiping and washing: List and
location of components 85A-1
Windscreen wiper blade:
Removal - Refitting 85A-5
Windscreen wiper arm:
Removal - Refitting 85A-6
Windscreen wiper
mechanism: Removal -
Refitting 85A-10
Windscreen wiper motor:
Removal - Refitting 85A-12
Rear screen wiper blade:
Removal - Refitting 85A-16
Rear screen wiper arm:
Removal - Refitting 85A-17
Rear screen wiper motor :
Removal - Refitting 85A-19
Rain and light sensor:
Removal - Refitting 85A-20

82A-8
ENGINE IMMOBILISER
Battery for remote door locking control: Removal - Refitting82A
REMOVAL
OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolt (1) .
aOpen the key with a small flat-blade screwdriver at
(2) .aRemove the battery (3) from the door locking remote
control using a small flat-blade screwdriver.
REFITTING
REFITTING OPERATION FOR PART CONCERNED
a
aFit the door locking remote control battery.
aClose the key.
aTighten the bolt.
107732
107733
107731
WARNING
To ensure that the remote control operates cor-
rectly, take care not to damage the battery con-
tacts.
Only handle the new battery with dry, grease-free
hands or wearing clean gloves to avoid any risk
of dir t and oxidation on the battery.

87C-1
OPENING ELEMENT MANAGEMENT
Opening elements management: List and location of components87C
I - LIST OF COMPONENTS
II - LOCATION OF COMPONENTS
1 - UCH
The UCH is located in the dashboard, above the pas-
senger compartment relay/fuse box; to remove it (see
87B, Passenger compartment connection unit,
UCH: Removal - Refitting, page 87B-1) .2 - Passenger compartment fuse and relay box
3 - Remote door locking control
To replace the battery (see 82A, Engine immobiliser,
Battery for remote door locking control: Removal -
Refitting, page 82A-8) . No. Description
(1) UCH
(2) Passenger compartment fuse and relay
box
(3) Remote door locking control
(4) Centr al door locking switch
(5) Tailgate opening switch
119507
119504
107733

88A-66
WIRING HARNESS
Driver's front side door wiring: Removal - Refitting
LEFT-HAND DRIVE
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aFully raise the window winder.
aswitch off the ignition
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the front side door trim (see Front side
door trim: Removal - Refitting) (MR 412, 72A,
Side opening element trim).
aDisconnect the electric door mirror connector.
aRemove the front speaker (see 86A, Radio, Front
speakers: Removal - Refitting, page 86A-8) .
aRemove the door sealing film (see Door sealing
film: Removal - Refitting) (MR 412, 65A, Opening
element sealing).aRemove the front side door electric window winder
mechanism (see Front side door electric window
mechanism: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms).
aRemove the front side door lock (see Front side
door lock: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms). IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
WARNING
To prevent damaging the connectors, consult the
disconnection procedures (see Disconnecting the
connectors) (Technical Note 6015A, 88A, Wiring).
DOOR MIRRORS 02 or DOOR MIRRORS 03 or
DOOR MIRRORS 04
WITH 2 SPEAKERS, WITHOUT RADIO or WITH 4
SPEAKERS, WITHOUT RADIO or RADIO NO. 01
or RADIO NO. 03
ELECTRIC FRONT WINDOW or ONE-TOUCH
ELECTRIC PASSENGER WINDOW CONTROL
DRIVER'S ELECTRIC DOOR + REMOTE CON-
TROL

88A-67
WIRING HARNESS
Driver's front side door wiring: Removal - Refitting
LEFT-HAND DRIVE
88A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
a
aDisconnect the front side door R3 connector.
aUnclip the clips (1) using unclipping pliers.
aRemove the front side door wiring.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with a cpmplete wiring harness, lock the
unused connectors (see Connector: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the front side door wiring.
aAttach the clips (1) .
aConnect the front side door R3 connector.
III - FINAL OPERATION.
aRefit the front side door lock (see Front side door
lock: Removal - Refitting) (MR 412, 51A, Side ope-
ning element mechanisms).
aRefit the front side door electric window winder me-
chanism (see Front side door electric window
mechanism: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms).
aRefit the door sealing film (see Door sealing film:
Removal - Refitting) (MR 412, 65A, Opening ele-
ment sealing).
122352
WARNING
To prevent any risk of noise, premature wear,
short circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.
WARNING
To prevent any damage during the refitting ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
122352
DRIVER'S ELECTRIC DOOR + REMOTE CON-
TROL
ELECTRIC FRONT WINDOW or ONE-TOUCH
ELECTRIC PASSENGER WINDOW CONTROL

88A-69
WIRING HARNESS
Driver's front side door wiring: Removal - Refitting
RIGHT-HAND DRIVE
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aFully raise the window winder.
aswitch off the ignition
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the front side door trim (see Front side
door trim: Removal - Refitting) (MR 412, 72A,
Side opening element trim).
aDisconnect the electric door mirror connector.
aRemove the front speaker (see 86A, Radio, Front
speakers: Removal - Refitting, page 86A-8) .
aRemove the door sealing film (see Door sealing
film: Removal - Refitting) (MR 412, 65A, Opening
element sealing).aRemove the front side door electric window winder
mechanism (see Front side door electric window
mechanism: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms).
aRemove the front side door lock (see Front side
door lock: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms). IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
WARNING
To prevent damaging the connectors, consult the
disconnection procedures (see Connector: Dis-
connection and reconnection) (Technical Note
6015A, 88A, Wiring).
DOOR MIRRORS 02 or DOOR MIRRORS 03 or
DOOR MIRRORS 04
WITH 2 SPEAKERS, WITHOUT RADIO or WITH 4
SPEAKERS, WITHOUT RADIO or RADIO NO. 01
or RADIO NO. 03
ELECTRIC FRONT WINDOW or ONE-TOUCH
ELECTRIC PASSENGER WINDOW CONTROL
DRIVER'S ELECTRIC DOOR + REMOTE CON-
TROL

88A-70
WIRING HARNESS
Driver's front side door wiring: Removal - Refitting
RIGHT-HAND DRIVE
88A
II - REMOVAL OPERATION FOR PART
CONCERNED
a
aDisconnect the R 4 front side door connector.
aUnclip the clips (1) using unclipping pliers.
aRemove the front side door wiring.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with more wiring, immobilise the unused
connectors (see Connector: Sealing and immobi-
lising) (Technical Note 6015A, 88A, Wiring).II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the front side door wiring.
aAttach the clips (1) .
aConnect the R 4 front side door connector.
III - FINAL OPERATION.
aRefit the front side door lock (see Front side door
lock: Removal - Refitting) (MR 412, 51A, Side ope-
ning element mechanisms).
aRefit the front side door electric window winder me-
chanism (see Front side door electric window
mechanism: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms).
aRefit the door sealing film (see Door sealing film:
Removal - Refitting) (MR 412, 65A, Opening ele-
ment sealing).
122353
WARNING
To prevent any risk of noise, premature wear,
short circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.
WARNING
To prevent any damage during the refitting ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
122353
DRIVER'S ELECTRIC DOOR + REMOTE CON-
TROL
ELECTRIC FRONT WINDOW or ONE-TOUCH
ELECTRIC PASSENGER WINDOW CONTROL

88A-72
WIRING HARNESS
Passenger's front side door wiring: Removal - Refitting
LEFT-HAND DRIVE
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRaise the window window fully.
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the front side door trim (see Front side
door trim: Removal - Refitting) (MR 412, 72A,
Side opening element trim).
aDisconnect the electric door mirror connector.
aRemove the front speaker (see 86A, Radio, Front
speakers: Removal - Refitting, page 86A-8) .
aRemove the door sealing film (see Door sealing
film: Removal - Refitting) (MR 412, 65A, Opening
element sealing).aRemove the front side door electric window winder
mechanism (see Front side door electric window
mechanism: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms).
aRemove the front side door lock (see Front side
door lock: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms). IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
WARNING
To prevent damaging the connectors, consult the
disconnecting procedure (see Disconnecting
the connectors) (Technical Note 6015A, 88A,
Wiring).
DOOR MIRRORS 02 or DOOR MIRRORS 03 or
DOOR MIRRORS 04
WITH 2 SPEAKERS, WITHOUT RADIO or WITH 4
SPEAKERS, WITHOUT RADIO or RADIO NO. 01
or RADIO NO. 03
ELECTRIC FRONT WINDOW or ONE-TOUCH
ELECTRIC PASSENGER WINDOW CONTROL
DRIVER'S ELECTRIC DOOR + REMOTE CON-
TROL

88A-73
WIRING HARNESS
Passenger's front side door wiring: Removal - Refitting
LEFT-HAND DRIVE
88A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
a
aDisconnect the R 4 front side door connector.
aUnclip the clips (2) using unclipping pliers.
aRemove the front side door wiring.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with more wiring, lock the unused con-
nectors (see Connector: Sealing and locking)
(Technical Note 6015A, 88A, Wiring).II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the front side door wiring.
aAttach the clips (2) .
aConnect the R 4 front side door connector.
III - FINAL OPERATION.
aRefit the front side door lock (see Front side door
lock: Removal - Refitting) (MR 412, 51A, Side ope-
ning element mechanisms).
aRefit the front side door electric window winder me-
chanism (see Front side door electric window
mechanism: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms).
aRefit the door sealing film (see Door sealing film:
Removal - Refitting) (MR 412, 65A, Opening ele-
ment sealing).
122353
WARNING
To prevent any risk of noise, premature wear,
short circuits, etc. after the refitting operation,
mark the wiring routing and how to connect the
connectors.
WARNING
To prevent any damage during the refitting ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
122353
DRIVER'S ELECTRIC DOOR + REMOTE CON-
TROL
ELECTRIC FRONT WINDOW or ONE-TOUCH
ELECTRIC PASSENGER WINDOW CONTROL

88A-75
WIRING HARNESS
Passenger's front side door wiring: Removal - Refitting
RIGHT-HAND DRIVE
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aFully raise the window winder.
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the front side door trim (see Front side
door trim: Removal - Refitting) (MR 412, 72A,
Side opening element trim).
aDisconnect the electric door mirror connector.
aRemove the front speaker (see 86A, Radio, Front
speakers: Removal - Refitting, page 86A-8) .
aRemove the door sealing film (see Door sealing
film: Removal - Refitting) (MR 412, 65A, Opening
element sealing).aRemove the front side door electric window winder
mechanism (see Front side door electric window
mechanism: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms).
aRemove the front side door lock (see Front side
door lock: Removal - Refitting) (MR 412, 51A,
Side opening element mechanisms). IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
WARNING
To prevent damaging the connectors, consult the
disconnection procedures (see Connector: Dis-
connection and reconnection) (Technical Note
6015A, 88A, Wiring).
DOOR MIRRORS 02 or DOOR MIRRORS 03 or
DOOR MIRRORS 04
WITH 2 SPEAKERS, WITHOUT RADIO or WITH 4
SPEAKERS, WITHOUT RADIO or RADIO NO. 01
or RADIO NO. 03
ELECTRIC FRONT WINDOW or ONE-TOUCH
ELECTRIC PASSENGER WINDOW CONTROL
DRIVER'S ELECTRIC DOOR + REMOTE CON-
TROL