wheel bolts RENAULT TWINGO RS 2009 2.G Electrical Equipment Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 241
Page 19 of 241
80B-7
HEADLIGHTS
Halogen headlight: Removal - Refitting
80B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aSwitch off the ignition.
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection).II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the bolts (1) from the halogen headlight.
aRemove the halogen headlight.
119376
119375
Page 20 of 241
80B-8
HEADLIGHTS
Halogen headlight: Removal - Refitting
80B
aRemove the cover (2) from the halogen headlight.
aDisconnect the halogen headlight connectors.
aRemove:
-the headlight,
-the halogen headlight bulbs (see 80B, Headlights,
Halogen bulb: Removal - Refitting, page 80B-3) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the halogen headlight bulbs (see 80B, Headli-
ghts, Halogen bulb: Removal - Refitting, page
80B-3) .
aConnect the halogen headlight connectors.
aRefit:
-the halogen headlight cover,
-the halogen headlight,
-the halogen headlight bolts.
II - FINAL OPERATION.
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),-the front wheels (see Wheel: Removal - Refitting)
(MR 411, 35A, Wheels and tyres).
aAdjust the halogen headlights (see 80B, Headli-
ghts, Halogen headlight: Adjustment, page 80B-
9) .
119377
Page 22 of 241
80B-10
HEADLIGHTS
Front fog light: Removal - Refitting
80B
REMOVAL
I - REMOVAL PREPARATION OPERATION
Removing the left-hand fog light bulb
a
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).Removing the fog light bulb
aRemove:
-the lower bolts (1) of the front wheel arch liner,
-the bolt from the front section of the engine under-
tray on the side concerned.
Removing the fog light
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove:
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection). D4F, and 780
Note:
The front bumper must be removed in order to
remove the left-hand fog light bulb.
K4M, and 854
119264
Page 24 of 241
80B-12
HEADLIGHTS
Front fog light: Removal - Refitting
80B
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
1 - Refitting the fog light bulb
aReplace the fog light bulb with an approved bulb.
aRefit the fog light bulb.
aTurn the fog light bulb a quarter of a turn clockwise.
aConnect the fog light connector.
2 - Refitting the fog light
aRefit the front fog light.
II - FINAL OPERATION.
Refitting the left-hand fog light bulb
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
Refitting the fog light bulb
aRefit:
-the lower bolts of the front wheel arch liner,
-the bolt for the front section of the engine undertray
on the side concerned.
Refitting the fog light
aRefit:
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
D4F, and 780
K4M, and 854
Page 57 of 241
84A-2
CONTROL - SIGNALS
Steering column switch assembly: Removal - Refitting84A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
Set the wheels straight ahead.
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(88C, Airbags and pretensioners).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the rev counter (see 83A, Instrument pa-
nel, Rev counter: Removal - Refitting, page 83A-
3) .aRemove the lower cover bolts (1) .
aUnclip the upper cover at (2) .
aRemove the upper cover (3) . Equipment required
Diagnostic tool
WARNING
To prevent damaging the rotar y switch, do not turn
the mobile section of the rotary switch.
WARNING
Incorrect wheel alignment could ruin the rotary
switch.
ENGINE REV COUNTER
127437
127438
Page 139 of 241
88A-3
WIRING HARNESS
Front left-hand wiring: Removal - Refitting
LEFT-HAND DRIVE
88A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aSwitch off the ignition.
aRemove:
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (MR 412, 55A, Exterior
protection),
-the front bumper (see Front bumper: Removal -
Refitting) (MR 412, 55A, Exterior protection),
-the side indicators (see 80B, Headlights, Side in-
dicator: Removal - Refitting, page 80B-13) ,
-the master cylinder (see Master cylinder: Remo-
val - Refitting) (MR 411, 37A, Mechanical compo-
nent controls),
-the brake servo (see Brake servo: Removal - Re-
fitting) (MR 411, 37A, Mechanical component con-
trols),
-the left-hand suspended engine mounting (see
Left-hand suspended engine mounting: Remo-
val - Refitting) (MR 411, 19D, Engine mounting).aUnclip the glovebox.
aRemove the dashboard lower trim.
aDisconnect the cruise control switch connector (1) .
aRemove:
-the bolts (2) IMPORTANT
Consult the safety and cleanliness advice and ope-
ration recommendations before carrying out any
repair (see 88A, Wiring harness, Wiring: Precau-
tions for the repair, page 88A-2) .
Note:
The dashboard does not need to be removed in
order to access the pedal wiring.
119506
CRUISE CONTROL
121212