lights RENAULT TWINGO RS 2009 2.G Engine And Peripherals Multimedia Connection Unit Workshop Manual

86D -2V1 MR-413-X44-86D000$010.mif
86D
BIC
Vdiag No.: 14
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding method applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
Fault finding procedure
To run fault finding on the vehicle computers, switch on the ignition.
Depending on the type of vehicle equipment, proceed as follows:
To cut off + after ignition feed, proceed as follows:Vehicle(s): CLIO III and NEW TWINGOComputer name: MULTIMEDIA CONNECTION
UNIT
Function concerned: MULTIMEDIA
CONNECTION UNITVdiag No.: 14
Special tooling required
Diagnostic tool
Multimeter
Elé. 1681 Universal bornier
For vehicles with key/radio frequency remote control, use the key to switch on the ignition.
For vehicles with Renault cards,
–with the vehicle card in the card reader,
–press and hold the start button (longer than 5 seconds) with start-up conditions not fulfilled,
connect the diagnostic tool and perform the required operations.
For vehicles with key/radiofrequency remote control,use the key to switch off the ignition.
For vehicles with Renault cards,
Press the Start button twice briefly (less than 3 seconds),
Ensure that the + after ignition feed has been cut off by checking that the computer warning lights on the instrument
panel have gone out.
BIC_V14_PRELI
MULTIMEDIA CONNECTION UNIT
Fault finding – Introduction

86D-12V1 MR-413-X44-86D000$030.mif
86D
BIC
Vdiag No.: 14
Role of main components
–Multimedia network interface unit: enables information to be exchanged between the “vehicle” and “multimedia”
multiplex networks.
The multimedia network interface unit is integrated into the display computer on vehicles not equipped with a
navigation system.
If the vehicle is equipped with a navigation system, the multimedia network interface unit is a computer which is
independent of the display: the multimedia connection unit, located behind the glovebox on the passenger side.
The multimedia connection unit (Display or Multimedia connection unit) receives various signals from the vehicle
CAN (speed, status of exterior lights) and retransmits them for the radio via the Multimedia CAN.
The multimedia connection unit (Display or Multimedia connection unit) transmits the activation signal to the radio
and to the other computers participating in the multimedia function when the user switches on the radio or starts the
vehicle.
The multimedia connection unit is involved in the radio anti-theft protection system.
The protection is based on an identifier, the "Vehicle ID", sent on the CAN-V by the instrument panel computer. The
multimedia connection unit reads the "Vehicle ID" on the CAN-V and sends it to the CAN-M for the multimedia type
computers.
The multimedia connection unit allows the optimum configuration of the sound volume according to the vehicle
speed.
–Display: displays various multimedia system data such as the station selected, time, CD listing and satellite
guidance information.
–Radio control satellite: allows the different functions of the multimedia system to be accessed through the radio
control satellite.
–Radio/navigation computer: manages the various multimedia system functions according to user requests and
transmits audio data to the vehicle via the speakers.
MULTIMEDIA CONNECTION UNIT
Fault finding – Role of components

86D-28V1 MR-413-X44-86D000$100.mif
86D
BIC
Vdiag No.: 14
MAIN SCREEN
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
checked or actionDisplay
and notesFault finding
Side lightsET004:+12 V Side
lightsINACTIVE
INVALID
OFF
ONIn the event of an inconsistency,
run fault finding on the UCH (see
87B, Passenger compartment
connection unit).
BIC_V14_CCONF
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check

86D-31V1 MR-413-X44-86D000$100.mif
MULTIMEDIA CONNECTION UNIT
Fault finding – Conformity check86D
BIC
Vdiag No.: 14
FUNCTION: MULTIMEDIA
SUB-FUNCTION: DISPLAY
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on, and the radio switched on.
FunctionParameter or status
Checked or actionDisplay and notes Fault finding
DisplayAC001:Display testThis command is used
to test the liquid crystal
screen of the display.None
LightingET004:+12 V Side lightsOFF
ON
INVALID
INACTIVEIn the event of an
inconsistency, run fault
finding on the UCH (see
87B, Passenger
compartment
connection unit).
ET007:BrightnessPANEL GAP
NIGHTIn the event of an
inconsistency, consult the
interpretation of ALP 4
Lighting does not
change when the
vehicle lights are
switched on.

86D-32V1 MR-413-X44-86D000$110.mif
86D
BIC
Vdiag No.: 14
Tool status Diagnostic tool title
ET002Radio on/off button
ET004+12 V Side lights
ET007Brightness
ET009Repeat button (only on Clio III)
ET011+ button
ET012- button
ET017Wheel action
ET020Mute button
ET023Source button
ET024Mode button
ET055Telephone button
MULTIMEDIA CONNECTION UNIT
Fault finding – Status summary table