belt RENAULT TWINGO RS 2009 2.G Engine And Peripherals Service Manual

11A-30
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D7F, and 800
11A
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the front right-hand wheel arch liner (see MR 412
Bodywork, 55A, Exterior protection, Front
wheel arch liner: Removal-Refitting),
-the front right-hand wheel ( (see Wheel: Removal
- Refitting) .
aConnect the battery ( (see Battery: Removal - Re-
fitting) .

11A-31
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see ) (80A, Battery).
aRemove:
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the rear suspended engine mounting (see 19D,
Engine mounting, Lower engine tie-bar: Re-
moval - Refitting, page 19D-18) .aSet up the engine support tool (Mot. 1379), shifting
the engine forwards.
aLift the engine slightly using the (Mot. 1379).
aRemove:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) .
aRefit the crankshaft accessories pulley bolt.
aUnclip the fuel pipe from the upper timing cover. Special tooling required
Mot. 1379Engine suppor t tool for cylin-
der head oper ations.
Mot. 1054TDC setting pin.
Tightening torquesm
tensioning roller nut24 N.m
lower timing cover bolt10 N.m
intermediate timing
cover bolts10 N.m
upper timing cover bolts37 N.m
10267

11A-32
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
aMove the flexible heat shield away from the oil pres-
sure sensor connector.
aDisconnect the oil pressure sensor connector (1) .
aUnclip the oil pressure sensor wiring from the upper
timing cover.
aMove the oil pressure sensor connector to one side.aRemove:
-the bolts (1) from the upper timing cover,
-the upper timing cover.
aRemove:
-the intermediate timing cover bolts (2) ,
-the timing intermediate housing,
-the lower timing cover bolt (3) ,
-the lower timing cover. D4F, and 780 or 782
122664
109740
109739

11A-33
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
1 - Adjusting the timing
aTurn the crankshaft clockwise (timing end). Stop a
half-tooth before the crankshaft sprocket mark is
lined up with the fixed marking.a
aInsert the TDC setting pin (Mot. 1054).
aTurn the crankshaft clockwise until it is stopped.
109737
109735
Note:
Cer tain vehicles are fitted with a flywheel protec-
tor positioned on the setting opening.
In this case, it is necessar y to remove the starter
and protector to be able to insert the TDC setting
pin.

11A-34
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
aMake sure that the mark on the camshaft sprocket
and the mark on the crankshaft sprocket are aligned
with their fixed markings.
2 - Removing the timing belt
aRemove:
-the nut (4) from the tensioning roller,
-the tensioning roller,
-the timing belt (5) .
REFITTING
I - REFITTING PREPARATION OPERATION
aparts always to be replaced: Timing belt,
parts always to be replaced: Timing belt tension-
ing roller,
parts always to be replaced: Crankshaft acces-
sories pulley bolts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the new tensioning roller, making sure:
-that the cylinder head ribbing is between the two
tensioning roller lugs,
-that the tensioning roller pin is properly positioned,
-that the tensioning roller is positioned as in the dia-
gram.
aDo not remove the pin from the new tensioning roller
before refitting the timing belt.
aScrew on the tensioning roller nut without tightening
it.
109738
109738
109761

11A-35
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
aRefit the new timing belt:
-by lining up the crankshaft sprocket mark with the
mark on the inside of the timing belt,
-by lining up the camshaft sprocket mark with the
mark on the outside of the timing belt.
Procedure for tensioning timing belt
aRemove:
-the TDC setting pin,
-the tension wheel pin.aTurn the tensioning roller eccentric anti-clockwise,
using a 6 mm Allen key, to bring the adjustable in-
dex level with the fixed index.
aTorque tighten the tensioning roller nut (24 N.m).
aRotate the crankshaft through six revolutions in a
clockwise direction (timing end).
aSet the timing using the TDC setting pin (Mot. 1054).
109762109763

11A-36
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
aMake sure that the mark on the camshaft sprocket
and the mark on the crankshaft sprocket are aligned
with their fixed markings.
aRemove the TDC setting rod (Mot. 1054).aLoosen the tensioning roller nut up to one turn,
maintaining the position of the tensioning roller ec-
centric using a 6 mm Allen key.
aTurn the tensioning roller eccentric clockwise, using
a 6 mm Allen key, to bring the adjustable index to
the centre of the two fixed indexes.
aTorque tighten the tensioning roller nut (24 N.m),
maintaining the position of the eccentric using a 6
mm Allen key.
109737
109738109764

11A-37
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
D4F
11A
aCheck that the tensioning roller does not come into
contact with the cylinder head.
aIf the tensioning roller is in contact with the cylinder
head:
-set the engine to Top Dead Centre,
-remove the tensioning roller and the timing belt,
-insert the tensioning roller pin,
-repeat the timing belt refitting method from the be-
ginning, step by step.
III - FINAL OPERATION
aRefit:
-the lower timing cover,
-the lower timing cover bolt,
-the timing intermediate housing,
-the intermediate timing cover bolts,
-the upper timing cover,
-the upper timing cover.
aTorque tighten:
-the lower timing cover bolt (10 N.m),
-the intermediate timing cover bolts (10 N.m),
-the upper timing cover bolts (37 N.m)aFit the oil pressure sensor connector.
aClip the oil pressure sensor wiring on the upper tim-
ing cover.
aConnect the oil pressure sensor connector.
aFit the flexible heat shield on the oil pressure sensor
connector.
aClip the fuel pipe on to the upper timing cover.
aRefit:
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the rear suspended engine mounting (see 19D,
Engine mounting, Lower engine tie-bar: Re-
moval - Refitting, page 19D-18) .
aRemove the tool (Mot. 1379).
aRefit:
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the front right-hand wheel arch liner (see Front
wheel arch liner: Removal - Refitting) (55A, Ex-
terior protection),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres).
aConnect the battery (see ) (80A, Battery).
109765
D4F, and 780 or 782

11A-38
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).aRemove:
-the engine cover,
-the windscreen wiper arms (see Windscreen wip-
er arm: Removal - Refitting) (85A, Wiping -
Washing),
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (56A, Exterior equipment),
-the scoop under the scuttle panel grille (see Scoop
under the scuttle panel grille: Removal - Refit-
ting) (56A, Exterior equipment),
-the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
-the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
-the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
-the halogen headlights (see Halogen headlight:
Removal - Refitting) (80B, Headlights),
-the front upper cross member (see Front upper
cross member: Removal - Refitting) (42A, Upper
front structure),
-the lower engine tie-bar (see 19D, Engine mount-
ing, Lower engine tie-bar: Removal - Refitting,
page 19D-18) ,
-the right-hand suspended engine mounting (see
19D, Engine mounting, Right-hand suspended
engine mounting: Removal - Refitting, page
19D-13) ,
-the camshaft position sensor (see 13B, Diesel in-
jection, Camshaft position sensor: Removal -
Refitting, page 13B-14) ,
-the accessories belt (see 11A, Top and front of
engine, Accessories belt: Removal - Refitting,
page 11A-3) ,
-the crankshaft accessories pulley (see 11A, Top
and front of engine, Crankshaft accessories
pulley: Removal - Refitting, page 11A-20) . Special tooling required
Mot. 1672Low er engine support.
Mot. 1489TDC locating pin.
Mot. 1430Set of 5 crankshaft and cam-
shaft pulley timing pins.
Tightening torquesm
tensioning roller bolt27 N.m
camshaft pulley wheel
bolts14 N.m
TDC setting pin plug25 N.m
cylinder head sus-
pended mounting bolts25 Nm
IMPORTANT
Wear protective gloves during the operation.
WARNING
The belt must be replaced with a new one if it has
been removed.
WARNING
When replacing the belt, always replace the tension
wheels and idler pulleys.
WARNING
Do not r un the engine without the accessories belt
to avoid damaging the crankshaft accessories pul-
ley.

11A-39
TOP AND FRONT OF ENGINE
Timing belt: Removal - Refitting
K9K
11A
aRefit the old crankshaft accessories pulley bolt (1)
fitted with a spacer (2) (which does not cover the tim-
ing sprocket mark).
aUnclip the upper timing cover at (3) .
aRemove the upper timing cover (4) .
aRaise the engine using the lower tool (Mot. 1672).
aUnclip the lower timing cover at (5) .
aLower the engine using the lower tool (Mot. 1672).
aRemove:
-the plastic clip (6) from the lower timing cover,
107272
K9K, and 740
19654
19654-1