light RENAULT TWINGO RS 2009 2.G Engine Diesel Injection Owner's Guide

13B-97
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50
DF099
PRESENT
OR
STOREDAUTOMATIC TRANSMISSION OR SEQUENTIAL GEARBOX
CONNECTION VIA THE MULTIPLEX NETWORK
1.DEF: No signal
NOTESSpecial notes:
–Gearbox does not change gear in automatic mode.
–OBD warning light illuminated.
See Technical Note Wiring Diagrams of the vehicle concerned.
Run a multiplex network test (see 88B, Multiplex).
Check the connection and condition of connector A (black 52-track) of the sequential gearbox computer,
component code 119.
Check the connection and condition of connector C (brown 48-track) of the injection computer, component
code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, the continuity and the absence of interference resistance on the following connections:
–3MT between components 119 and 120,
–3MS between components 119 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
DCM1.2_V48_DF099/DCM1.2_V4C_DF099/DCM1.2_V50_DF099

13B-98
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
* C2I: Individual injector correction
DF107
PRESENT
OR
STOREDCOMPUTER MEMORY
NOTESConditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
Special notes:
If fault DF107 is present: the engine stops and cannot be restarted and the level 2
warning light illuminates, with the message Faulty injection displayed on
the instrument panel.
Enter the individual injector corrections (C2I*) using the diagnostic tool (command SC002 Enter injector
codes).
If the fault is still present, contact the Techline.
DCM1.2_V48_DF107/DCM1.2_V4C_DF107/DCM1.2_V50_DF107/DCM1.2_V54_DF107/DCM1.2_V58_DF107/DCM1.2_V5C_DF107

13B-100
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF113
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE
1.DEF: At minimum limit
2.DEF: At maximum limit
NOTESSpecial notes:
If fault DF113 is present: the engine stops immediately and cannot be restarted.
The level 2 warning light illuminates with the message Faulty injection displayed on
the instrument panel.
See Technical Note Wiring Diagrams of the vehicle concerned.
Check the condition and connection of the connectors on all sensors with a + 5 V supply.
–Refrigerant pressure sensor.
–Cylinder reference sensor.
–Turbocharger inlet pressure sensor.
–Rail pressure sensor.
–Pedal sensor, gangs 1 and 2.
–EGR valve position sensor.
–Flow sensor.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s), otherwise replace the wiring.
Check the condition and connection of the injection computer connectors, component code 120.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s), otherwise replace the wiring.
To locate a possible internal fault on one of the sensors with a + 5 V supply (short circuit), disconnect each of
the sensors on the above list in turn, checking after each disconnection whether the fault changes status from
present to stored.
If the faulty sensor is located, check its connections and that it is in order.
If necessary replace the sensor.
DCM1.2_V48_DF113/DCM1.2_V4C_DF113/DCM1.2_V50_DF113/DCM1.2_V54_DF113/DCM1.2_V58_DF113/DCM1.2_V5C_DF113

13B-102
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$110.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF114
PRESENT
OR
STOREDEGR SOLENOID VALVE CIRCUIT1.DEF: At minimum limit
2.DEF: At maximum limit
3.DEF: Inconsistency
4.DEF: Valve jammed
5.DEF: Valve clogged
NOTESPriority when dealing with a number of faults:
–DF113 Sensor supply voltage.
Special notes:
If fault DF114 is present: unstable engine speed and even stalling. Starting difficult
or even impossible when cold, smoke emissions and loss of performance possible. On
status 4.DEF, the level 1 warning light illuminates with the message Faulty injection
displayed on the instrument panel.
Conditions for applying fault finding procedures to stored faults:
The fault is present with the engine running.
See Technical Note Wiring Diagrams of the vehicle concerned.
K9K 766, 768, 724, 740, 800, 802, and 812 ENGINES (Euro 4):
Check the connection and condition of the EGR valve connector, component code 1460.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connections:
–3VP between components 1460 and 120,
–3VQ between components 1460 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for +5 V on connection 3GC of component 1460.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
DCM1.2_V48_DF114/DCM1.2_V4C_DF114/DCM1.2_V50_DF114/DCM1.2_V54_DF114/DCM1.2_V58_DF114/DCM1.2_V5C_DF114

13B-108
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$120.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF122
PRESENT OR
STOREDPEDAL POTENTIOMETER GANG 2 SUPPLY VOLTAGECO.1: open circuit or short circuit to +12 V.
CC.0: short circuit to earth.
NOTESSpecial notes:
If fault DF122 is present: the idle speed is locked at 1000 rpm, the engine performance
is reduced to 75%, and the level 1 warning light illuminates with the message
Check injection displayed on the instrument panel.
See Technical Note Wiring Diagrams of the vehicle concerned
CC.0
NOTESNone.
Check the connection and condition of the pedal potentiometer connector, component code 921.
Check the connection and condition of connector A (black 32-track) of the injection computer, component
code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run test 14 Accelerator pedal check.
Check for earth on connection 3LV of component 921.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation and continuity of the following connection:
–3LU between components 921 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Disconnect connector A of the injection computer and the connector of the pedal potentiometer, component
code 921.
Check the insulation against earth of connection 3LU of component 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
DCM1.2_V48_DF122/DCM1.2_V4C_DF122/DCM1.2_V50_DF122/DCM1.2_V54_DF122/DCM1.2_V58_DF122/DCM1.2_V5C_DF122

13B-110
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$120.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF130
PRESENT OR
STOREDFLOW CAPACITY FUNCTION1.DEF: High flow current < minimum
2.DEF: High flow current > maximum
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine running.
Special notes:
If fault DF130 is present: the engine may stop with the level 2 warning light illuminated
and the message Faulty injection displayed on the instrument panel.
See Technical Note Wiring Diagrams of the vehicle concerned
Check the connection and condition of the flow actuator (IMV) connector, component code 1105.
Check the connection and condition of connector B (brown 48-track) of the injection computer, component
code 120.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s), otherwise replace the wiring.
Check the insulation and continuity of the following connection:
–3HI between components 1105 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance between connections 3HI and 3FB1 or 3FB2 (for New Twingo) or 3FB3 (for Kangoo 2) of
component 1105.
If the resistance of the flow actuator is not between 4.8 Ω and 5.8 Ω at 20
°C, replace the flow actuator, component
code 1105 (see MR 364 (Mégane II), MR 370 (Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New
Twingo), MR 417 (Kangoo 2), Mechanical, 13B, Diesel injection, Flow actuator: Removal - Refitting).
Check the presence and conformity of the fuel in the tank. Run Test 13: Diesel fuel conformity check.
Run Test 1 Low pressure circuit check and repair if necessary.
Run Test 6: High pressure system check.
If the fault is still present, contact the Techline.
DCM1.2_V48_DF130/DCM1.2_V4C_DF130/DCM1.2_V50_DF130/DCM1.2_V54_DF130/DCM1.2_V58_DF130/DCM1.2_V5C_DF130

13B-115
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$120.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF261
PRESENT OR
STOREDTURBOCHARGER ACTUATOR CIRCUITCO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 volts
NOTESSpecial note:
If fault DF261 is present, the air flow regulation is switched off, the EGR valve is
closed, and the turbocharging regulation is switched off. The level 1 warning light
illuminates with the message Faulty injection displayed on the instrument panel, and
the performance is reduced.
See Technical Note Wiring Diagrams of the vehicle concerned
Run TEST 11 Air line at the turbocharger.
Run TEST 5 Inlet circuit check.
Run TEST 10 Turbocharger control solenoid valve check.
Run TEST 12 Turbocharger.
Check the inlet pressure signal, check the gear number when changing gear.
If the fault is still present, contact the Techline.
DCM1.2_V48_DF261/DCM1.2_V4C_DF261/DCM1.2_V50_DF261/DCM1.2_V54_DF261/DCM1.2_V58_DF261/DCM1.2_V5C_DF261

13B-116
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$120.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF427
PRESENT OR
STOREDTURBO ACTUATOR CONTROL1.DEF: At minimum limit
2.DEF: At maximum limit
NOTESSpecial note:
If fault DF427 is present, the air flow regulation is switched off, the EGR valve is closed,
and the turbocharging regulation is switched off. On status 2.DEF, the level 1 warning
light illuminates and the performance is reduced.
Priority when dealing with a number of faults:
–DF261 Turbocharger actuator circuit.
See Technical Note Wiring Diagrams of the vehicle concerned
Run TEST 11 Air line at the turbocharger.
Run TEST 5 Inlet circuit check.
Run TEST 10 Turbocharger control solenoid valve check.
Run TEST 12 Turbocharger.
Check the turbocharging pressure signal, check the gear number when changing gear.
If the fault is still present, contact the Techline.
DCM1.2_V48_DF427/DCM1.2_V4C_DF427/DCM1.2_V50_DF427/DCM1.2_V54_DF427/DCM1.2_V58_DF427/DCM1.2_V5C_DF427

13B-118
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$120.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF631
PRESENT OR
STOREDBRAKE LIGHT SWITCH SIGNAL1.DEF: No signal
2.DEF: Inconsistency
NOTESConditions for applying the fault finding procedure to stored faults
Apply the fault finding procedure below if the fault is present or stored.
Special notes:
The fault is declared present when decelerating, when the brake pedal is depressed.
The cruise control function is inhibited.
See Technical Note Wiring Diagrams of the vehicle concerned
Check the connection and condition of the brake light switch connector, component code 160.
Check the connection and condition of the injection computer connector, component code 120.
If the connector(s) is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for +12 V on connection AP10 (for New Twingo) or BPT (for Mégane II, Scénic II, Modus, and Clio III) or
BPT2 (for Kangoo 2) and SP17 (for Mégane II, Scénic II, Modus, Kangoo 2, and Clio III) of component 160.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the operation of the brake light switch, component code 160.
Repair if necessary.
DCM1.2_V48_DF631/DCM1.2_V4C_DF631/DCM1.2_V50_DF631/DCM1.2_V54_DF631/DCM1.2_V58_DF631/DCM1.2_V5C_DF631

13B-119
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V6 MR-413-X44-13B000$120.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
DF631
CONTINUED
Check the insulation and continuity of the following connections:
–5A between components 160 and 120,
–BPT between components 160 and 645 (for Mégane II, Scénic II, Modus and Clio III),
–AP10 between components 160 and 1016 (for New Twingo),
–BPT2 between components 160 and 645 (for Kangoo 2),
–SP17 between components 160 and 260 (for Kangoo 2),
–65A between components 160 and 645 (vehicle without ESP),
–65G between components 160 and 645 (vehicle with ESP).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, replace the brake light switch, component code 160 (see MR 364 (Mégane II), MR 370
(Scénic II), MR 385 (Modus), MR 392 (Clio III), MR 411 (New Twingo), MR 417 (Kangoo 2), Mechanical, 37A,
Mechanical component controls, Brake light switch: Removal - Refitting).
If the fault is still present, contact the Techline.