open bonnet RENAULT TWINGO RS 2009 2.G Mechanism And Accessories Workshop Manual

TWINGO - Section 5
Contents
Pages
TWINGO - Section 5 ContentsPages
51A SIDE OPENING ELEMENT MECHANISMS
Front side door lock:
Removal - Refitting 51A-1
Front side door lock barrel:
Removal - Refitting 51A-3
Exter ior door handle:
Removal - Refitting 51A-5
Front side door electric
window mechanism:
Removal - Refitting 51A-6
Front side door manual
window winder mechanism:
Removal - Refitting 51A-8
Front side door check strap:
Removal - Refitting 51A-10
52ANON-SIDE OPENING ELEMENT
MECHANISMS
Bonnet lock: Removal -
Refitting 52A-1
Bonnet release cable:
Removal - Refitting 52A-2
Tailgate lock: Removal -
Refitting 52A-3
Tailgate strut: Removal -
Refitting 52A-4
Tailgate exterior opening
control: Removal - Refitting 52A-5
Sunroof operating
mechanism: Removal -
Refitting 52A-6
Sunroof mobile panel:
Removal - Refitting 52A-9
Sunroof mobile panel guide:
Removal - Refitting 52A-12
Sunroof deflector: Removal -
Refitting 52A-14
Sunroof sun visors: Removal
- Refitting 52A-15
54A WINDOWS
Windscreen: Removal -
Refitting 54A-1
Front side door sliding
window: Removal - Refitting 54A-3
Rear quar ter panel window:
Removal - Refitting 54A-4
Rear screen: Removal -
Refitting 54A-5
Sunroof fixed window:
Removal - Refitting 54A-7 52ANON-SIDE OPENING ELEMENT
MECHANISMS

52A-1
NON-SIDE OPENING ELEMENT MECHANISMS
Bonnet lock: Removal - Refitting
52A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the front bumper (see 55A, Exterior pro-
tection, Front bumper: Removal - Refitting, page
55A-1) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the bonnet catch nuts (1) through the openings (2)
in the front upper cross member,
-partially the bonnet catch.aUnclip:
-the clip (3) using a flat screwdriver,
-the bonnet opening cable sleeve stop (4) .
aRemove the bonnet catch.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aClip on:
-the clip (3) ,
-the bonnet opening cable sleeve stop (4) .
aRefit:
-the bonnet catch,
-the bonnet catch nuts (1) .
aPretighten the bonnet catch nuts.
aAdjust the play and flush fitting of the bonnet ( (see
Bonnet: Adjustment) ).
aTorque tighten the bonnet catch nuts (21 Nm).
II - FINAL OPERATION.
aRefit the front bumper (see 55A, Exterior protec-
tion, Front bumper: Removal - Refitting, page
55A-1) . Tightening torquesm
bonnet catch nuts21 Nm
121039
121038

52A-2
NON-SIDE OPENING ELEMENT MECHANISMS
Bonnet release cable: Removal - Refitting
52A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the battery ( (see Battery: Removal - Refitting) ),
-the battery tray ( (see Battery tray: Removal - Re-
fitting) ),
-the front wheel arch liner (see 55A, Exterior pro-
tection, Front wheel arch liner: Removal - Refit-
ting, page 55A-18) ,
-the front bumper (see 55A, Exterior protection,
Front bumper: Removal - Refitting, page 55A-1)
,
-the bonnet catch (see 52A, Non-side opening ele-
ment mechanisms, Bonnet lock: Removal - Re-
fitting, page 52A-1) ,
-the front door sill lining ( (see Front door sill
lining: Removal - Refitting) ).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolt (1) .
aUnclip the bonnet release catch.
aNote the route of the bonnet release cable.
aRemove the bulkhead cable routing blanking piece.
aRemove the bonnet release cable.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the bonnet opening cable,
-the bulkhead cable routing blanking piece.
aClip on the bonnet release catch.
aRefit the bolt (1) .
II - FINAL OPERATION.
aRefit:
-the front door sill lining ( (see Front door sill
lining: Removal - Refitting) ),
-the bonnet catch (see 52A, Non-side opening ele-
ment mechanisms, Bonnet lock: Removal - Re-
fitting, page 52A-1) ,
-the front bumper (see 55A, Exterior protection,
Front bumper: Removal - Refitting, page 55A-1)
,
-the front wheel arch liner (see 55A, Exterior pro-
tection, Front wheel arch liner: Removal - Refit-
ting, page 55A-18) ,
-the battery tray ( (see Battery tray: Removal - Re-
fitting) ),
-the battery ( (see Battery: Removal - Refitting) ).
121145