battery RENAULT TWINGO RS 2009 2.G Panelwork Owner's Manual

43A-11
SIDE UPPER STRUCTURE
B-pillar reinforcement: Description
43A
III - POSITIONING OF LOCAL ELECTRICAL
EARTHSIMPORTANT
For welded connections in three thicknesses, the
spot welds on the part replaced should be made in
the same place as for the original joint to retain its
mechanical proper ties.
121249
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

44A-23
REAR UPPER STRUCTURE
Rear end panel assembly: Description
44A
II - PART FITTED III - POSITIONING OF LOCAL ELECTRICAL
EARTHS
Right-hand side
Left side
121231
WARNING
If the spot welds cannot be made as they were ori-
ginally using an electrical spot welding machine,
they should be replaced with plug welds after holes
have been drilled in the first panel.
IMPORTANT
For welded connections in three thicknesses, the
spot welds on the part replaced should be made in
the same place as for the original joint to retain its
mechanical proper ties.121249
121250
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

44A-26
REAR UPPER STRUCTURE
Rear end panel: Description
44A
Left side
121250
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

45A-6
TOP OF BODY
Roof front section: Description
45A
There is only one way of replacing this part:
-complete replacement.
This operation only affects versions equipped with a
sunroof.
I - COMPOSITION OF THE SPARE PART
II - PART IN POSITION
Complete replacementIII - POSITIONING OF LOCAL ELECTRICAL
EARTHS
121045
No. Description Type Thic-
kness
(mm)
(1) Front section of
roofMild
steel0.65
103642
IMPORTANT
For welded connections in three thicknesses, the
spot welds on the par t replaced should be made in
the same place as for the original joint to retain its
mechanical proper ties.
121246
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.

45A-7
TOP OF BODY
Roof rear section: Description
45A
There is only one way of replacing this part:
-complete replacement.
I - COMPOSITION OF THE SPARE PART
II - PART IN POSITION
Complete replacementIII - POSITIONING OF LOCAL ELECTRICAL
EARTHS
121046
No. Description Type Thic-
kness
(mm)
(1) Rear section of
roofMild
steel0.65
121908
IMPORTANT
For welded connections in three thicknesses, the
spot welds on the part replaced should be made in
the same place as for the original joint to retain its
mechanical proper ties.
WARNING
If the spot welds cannot be made as they were ori-
ginally using an electrical spot welding machine,
they should be replaced with plug welds after holes
have been drilled in the first panel.
121250
IMPORTANT
To avoid damaging the vehicle's electric and elec-
tronic components, the battery and the earths of
any wiring harness near the weld area must be dis-
connected.
The earth of the welding machine must be placed
as close as possible to the weld area.