belt RENAULT TWINGO RS 2009 2.G Trim And Upholstery Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: TWINGO RS, Model: RENAULT TWINGO RS 2009 2.GPages: 60
Page 10 of 60
71A-7
BODY INTERNAL TRIM
Front door sill lining: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aUnclip the bonnet release catch.
aPartially remove the front side door seal.
aRemove:
-the front seat belt lower mounting (see Front seat
belt: Removal - Refitting) (MR 412, 59A, Safety
equipment),
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip the front door sill lining.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aClip on the front door sill lining.
II - FINAL OPERATION.
aRefit:
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the front seat belt lower mounting (see Front seat
belt: Removal - Refitting) (MR 412, 59A, Safety
equipment),
-the front side door seal.
aFit the bonnet release catch.
121144
121143
Note:
The front seat does not need to be removed to
remove the front door sill lining.
Page 13 of 60
71A-10
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPartially remove the door seal.
aRemove:
-the seat belt return reel (1) (see Front seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment),
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUnclip:
-the covers (2) ,
-the B-pillar upper trim at (2) .
aRemove the B-pillar upper trim.
121071
121076
121077
Page 14 of 60
71A-11
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting
71A
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the B-pillar upper trim.
aFit the B-pillar upper trim at (2) .
II - FINAL OPERATION.
aRefit:
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the seat belt return reel (1) (see Front seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment),
-the door seal.
Page 15 of 60
71A-12
BODY INTERNAL TRIM
Quarter panel trim: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPull the rear seats down or remove the rear bench
seatback (depending on equipment level) (see 76A,
Rear seat frames and mechanisms, Rear bench
seatback: Removal - Refitting, page 76A-5) .
aRemove:
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) .
aRemove the rear seat belt return reel (see Rear seat
belt: Removal - Refitting) (MR 412, 59A, Safety
equipment).aPartially remove the luggage compartment seal. (1)
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolt (2) .
aUnclip the rear quarter panel trim.
aRemove the rear quarter panel trim.
121065
121068
121067
Page 16 of 60
71A-13
BODY INTERNAL TRIM
Quarter panel trim: Removal - Refitting
71A
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the rear quarter panel lining.
aClip the rear quarter panel trim.
aRefit the bolt (2) .
II - FINAL OPERATION.
aRefit:
-the luggage compartment seal, (1)
-the rear seat belt return reel (see Rear seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment),
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) .
aPull the rear seats down or refit the rear bench seat-
back (depending on equipment level) (see 76A,
Rear seat frames and mechanisms, Rear bench
seatback: Removal - Refitting, page 76A-5) .
Page 24 of 60
75A-1
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners),
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners).II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the front seatback frame (see 75A, Front seat fra-
mes and mechanisms, Front seatback frame:
Removal - Refitting, page 75A-2) ,
-the front seat runners (see 75A, Front seat frames
and mechanisms, Front seat runner: Removal -
Refitting, page 75A-6) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front seatback frame (see 75A, Front seat fra-
mes and mechanisms, Front seatback frame:
Removal - Refitting, page 75A-2) ,
-the front seat runners (see 75A, Front seat frames
and mechanisms, Front seat runner: Removal -
Refitting, page 75A-6) .
II - FINAL OPERATION.
aRefit:
-the front buckle pretensioner (see Front buckle
pretensioner: Removal - Refitting) (MR 411,
88C, Airbags and seat belt pretensioners),
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners),
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the entire front seat (see 75A, Front seat frames
and mechanisms, Complete front seat: Remo-
val - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners). Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
Page 25 of 60
75A-2
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).
aRemove:
-the compete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners).aRemove:
-the bolts (1) ,
-the lumbar support. Equipment required
Diagnostic tool
Tightening torquesm
front seatback frame
bolts46 Nm
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121033
Page 28 of 60
75A-5
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting
75A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the front seatback frame bolts (5) ,
-the front seatback frame.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace the front seatback frame bolts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front seatback frame,
-the front seatback frame bolts (5) .
aTorque tighten the front seatback frame bolts (46
Nm).III - FINAL OPERATION.
aRefit:
-the unlocking cables to the front seat runners,
-the casing (4) .
-the rivets (3) ,
-the mounting for the control accessing the rear
seats (depending on the equipment level).
-the rivets (2) ,
-the seat back inclination control cable(s) (depen-
ding on the equipment level).
-the seat back inclination control cable upper
stop(s) (depending on the equipment level),
aClip on the various seat back inclination control ca-
ble lower stops (depending on the equipment level).
aRefit:
-the lumbar support,
-the bolts (1) ,
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners),
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the complete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners).
120849
Page 31 of 60
75A-8
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting
75A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and seat belt pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) (MR 411, 80A, Battery).aUnclip the cover (1) located under the front seat.
aDisconnect the connector (2) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the blanking covers (3) ,
-the front seat nuts (3) . Equipment required
Diagnostic tool
Tightening torquesm
front seat nuts35 Nm
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
120814
121326
Page 32 of 60
75A-9
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting
75A
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace the front seat nuts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the front seat nuts (3) .
aTorque tighten the front seat nuts (35 Nm).
aRefit the blanking covers (3) .
III - FINAL OPERATION.
aConnect the connector (2) .
aClip on the cover (1) located under the front seat.
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners).