seats RENAULT TWINGO RS 2009 2.G Trim And Upholstery Workshop Manual

71A-1
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aLock the airbag computer using the Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
aDisconnect the battery (see Battery: Removal - Re-
fitting) .
aRemove:
-the front seats completely (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) ,
-the rear seats completely (depending on equip-
ment level) (see 76A, Rear seat frames and me-
chanisms, Complete rear seat: Removal -
Refitting, page 76A-1) ,
-the rear bench seat base (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seat base: Removal - Refit-
ting, page 76A-6) ,
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) ,
-the centre front panel (see Centre front panel: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment),-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the front door sill lining (see 71A, Body internal
trim, Front door sill lining: Removal - Refitting,
page 71A-7) .
aRemove:
-the bolt (1) ,
-the storage compartment under the front seat. Equipment required
Diagnostic tool
IMPORTANT
To avoid any risk of triggering when working on or
near a pyrotechnic component (airbags or preten-
sioners), lock the airbag computer using the dia-
gnostic tool.
When this function is activated, all the trigger lines
are inhibited and the airbag warning light on the ins-
trument panel lights up contin uously (ignition on).
IMPORTANT
Never handle the pyrotechnic systems (pretensio-
ners or airbags) near to a source of heat or naked
flame - they may be triggered.
121608

71A-2
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting
71A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the centring pin (2) from the centre console,
-the clip (3) ,
-the floor carpet.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit the seat wiring.
aRefit:
-the floor carpet,
-the clip (3) ,
-the centre console centring pin (2) .II - FINAL OPERATION.
aRefit:
-the storage compartment under the front seat,
-the bolt (1) ,
-the front door sill lining (see 71A, Body internal
trim, Front door sill lining: Removal - Refitting,
page 71A-7) ,
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the centre front panel (see Centre front panel: Re-
moval - Refitting) (MR 412, 57A, Interior equip-
ment),
-the centre console (see Centre console: Removal
- Refitting) (MR 412, 57A, Interior equipment),
-the rear bench seatback (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seatback: Removal - Refit-
ting, page 76A-5) ,
-the rear bench seat base (depending on equipment
level) (see 76A, Rear seat frames and mecha-
nisms, Rear bench seat base: Removal - Refit-
ting, page 76A-6) ,
-the rear seats completely (depending on equip-
ment level) (see 76A, Rear seat frames and me-
chanisms, Complete rear seat: Removal -
Refitting, page 76A-1) ,
-the front seats completely (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) .
aUnlock the airbag computer using Diagnostic tool
(see Fault finding - Replacement of components)
(MR 413, 88C, Airbags and pretensioners).
121162

71A-12
BODY INTERNAL TRIM
Quarter panel trim: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPull the rear seats down or remove the rear bench
seatback (depending on equipment level) (see 76A,
Rear seat frames and mechanisms, Rear bench
seatback: Removal - Refitting, page 76A-5) .
aRemove:
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) ,
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) .
aRemove the rear seat belt return reel (see Rear seat
belt: Removal - Refitting) (MR 412, 59A, Safety
equipment).aPartially remove the luggage compartment seal. (1)
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolt (2) .
aUnclip the rear quarter panel trim.
aRemove the rear quarter panel trim.
121065
121068
121067

71A-13
BODY INTERNAL TRIM
Quarter panel trim: Removal - Refitting
71A
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the rear quarter panel lining.
aClip the rear quarter panel trim.
aRefit the bolt (2) .
II - FINAL OPERATION.
aRefit:
-the luggage compartment seal, (1)
-the rear seat belt return reel (see Rear seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment),
-the rear panel trim (see 71A, Body internal trim,
Rear panel lining: Removal - Refitting, page
71A-14) ,
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) .
aPull the rear seats down or refit the rear bench seat-
back (depending on equipment level) (see 76A,
Rear seat frames and mechanisms, Rear bench
seatback: Removal - Refitting, page 76A-5) .

71A-14
BODY INTERNAL TRIM
Rear panel lining: Removal - Refitting
71A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPull the rear seats down or remove the rear bench
seatback (depending on equipment level) (see 76A,
Rear seat frames and mechanisms, Rear bench
seatback: Removal - Refitting, page 76A-5) .
aRemove the rear parcel shelf side trim (see 71A,
Body internal trim, Rear parcel shelf side trim:
Removal - Refitting, page 71A-15) .
aPartially remove the front side door seal.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the clip (1) .aRemove the bolt (2) .
aUnclip the rear panel trim.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aFit the rear panel trim.
aRefit:
-the bolt (2) ,
-the clip (1) .
II - FINAL OPERATION.
aRefit:
-the front side door seal,
-the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-15) .
aPull the rear seats down or refit the rear bench seat-
back (depending on equipment level) (see 76A,
Rear seat frames and mechanisms, Rear bench
seatback: Removal - Refitting, page 76A-5) .
121069
121075

75A-3
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting
75A
aUnclip the various seat back inclination control cable
lower stops (depending on the equipment level).aRemove:
-the seat back inclination control cable upper
stop(s) (depending on the equipment level),
-the seat back inclination control cable(s) (depen-
ding on the equipment level).
aRemove:
-the rivets (2) ,
-the mounting from the control accessing the rear
seats.
120841
121196121192
121035

75A-5
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting
75A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the front seatback frame bolts (5) ,
-the front seatback frame.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aAlways replace the front seatback frame bolts.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the front seatback frame,
-the front seatback frame bolts (5) .
aTorque tighten the front seatback frame bolts (46
Nm).III - FINAL OPERATION.
aRefit:
-the unlocking cables to the front seat runners,
-the casing (4) .
-the rivets (3) ,
-the mounting for the control accessing the rear
seats (depending on the equipment level).
-the rivets (2) ,
-the seat back inclination control cable(s) (depen-
ding on the equipment level).
-the seat back inclination control cable upper
stop(s) (depending on the equipment level),
aClip on the various seat back inclination control ca-
ble lower stops (depending on the equipment level).
aRefit:
-the lumbar support,
-the bolts (1) ,
-the front side (chest-level) airbag (depending on
the equipment level) (see Front (chest-level) side
airbag: Removal - Refitting) (MR 411, 88C, Air-
bags and seat belt pretensioners),
-the front seat cushion trim (see 77A, Front seat
trim, Front seat base trim: Removal - Refitting,
page 77A-1) ,
-the front seatback trim (see 77A, Front seat trim,
Front seatback trim: Removal - Refitting, page
77A-4) ,
-the complete front seat (see 75A, Front seat fra-
mes and mechanisms, Complete front seat: Re-
moval - Refitting, page 75A-8) .
aConnect the battery (see Battery: Removal - Refit-
ting) (MR 411, 80A, Battery).
aUnlock the airbag computer using the Diagnostic
tool (see Fault finding - Replacement of compo-
nents) (MR 413, 88C, Airbags and seat belt preten-
sioners).
120849

77A-5
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
77A
aUnclip the control accessing the rear seats.
aRemove the elastic securing straps (3) from the
seatback trim.aRemove the retaining sections (4) .
aPartially remove the seatback cover.
aCut the clips (5) using a cutting tool.
120836
120811120943
120837

77A-6
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
77A
aUnclip the headrest guides (6) .
aRemove:
-the seatback cover,
-the seatback foam.
2 - 2nd type
aUnlock the headrest at (7) .
aRemove the headrest.aRemove:
-the bolt (8) ,
-the lever from the control accessing the rear seats.
aRemove:
-the bolts (9) ,
-the plate from the control accessing the rear seats.
120838
120834112944
112945

77A-9
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting
77A
aRemove:
-the bolt (20) ,
-the lever from the control accessing the rear seats.
aRemove:
-the bolts (21) ,
-the plate from the control accessing the rear seats.aRemove the elastic securing straps (22) from the
seatback trim.
aRemove the elastic securing strap (23) from the
seatback trim.
112944
112945120811
121460