RENAULT TWIZY 2012 1.G Manual Online

5.7
FRONT HEADLIGHTS: replacing bulbs (2/2)
Any operation on (or modi-
fication to) the electrical
system must be performed
by an authorised dealer
since incorrect connections could
damage the electrical equipment
(wiring, components). In addition,
your dealer has available all the
parts necessary for fitting electrical
components.
Cleaning the headlights
Use a soft cloth. If this does not clean
it properly, moisten the cloth with soapy
water then rinse off.
Finally, carefully dry off with a soft dry
cloth.
Cleaning products containing alco-
hol must not be used under any cir-
cumstances.
To comply with local legislation, or
as a precaution, you can obtain an
emergency kit containing a set of
spare bulbs and fuses from an ap-
proved dealer.
Direction indicator lights 6
Please contact an authorised dealer.
6

5.8
Side light and brake light 2
Bulb type: P21/5W.
Reversing indicator light 3
Bulb type: PY21W.Reversing/side and brake
lights
From inside the vehicle:
– unclip covers 1 using a flat-blade
screwdriver or similar;
– unscrew using a Torx tool.
From outside the vehicle:
– release the light unit by pulling it backwards;
– unscrew bulb holder 2 or 3 and re-
place the bulb.
Note: ensure that the cable is in place
before inserting the light unit.
REAR LIGHTS: changing bulbs (1/2)
Refitting
To refit, proceed in the reverse order,
taking care not to damage the wiring.
The bulbs are under pres-
sure and can break when
replaced.
Risk of injury.
1
2
3

5.9
REAR LIGHTS: changing bulbs (2/2)
Direction indicators 6
Please see an authorised dealer.
Number plate lights 5
– Unclip light 5 by pressing tab 4;
– remove the light cover to gain access to the bulb.
Bulb type: W5W.
The bulbs are under pres-
sure and can break when
replaced.
Risk of injury.
4
56

5.10
Fuse box
If any electrical component does not
work, check the condition of the fuses.
Apply the handbrake and unclip flap A.
Tweezers 1
Disconnect the fuse using pliers 1.
To remove the fuse from the tweezers,
slide the fuse to the side.
It is not advisable to use the free fuse
locations.
To repair fuses, use the fuse location
marking on the back of the flap A.
Check the fuse in question
and replace it, if neces-
sary, by a fuse of the same
rating.
If a fuse is fitted where the rating is
too high, it may cause the electrical
circuit to overheat (risk of fire) in the
event of an item of equipment using
an excessive amount of current.
FUSES (1/2)
1
A
In accordance with local legislation
or as a precautionary measure:
Obtain an emergency kit containing
a set of spare bulbs and fuses from
an approved Dealer.

5.11
FUSES (2/2)
SymbolAllocation SymbolAllocation
Traction batteryaInstrument panel
InverterU
STOPBrake lightsLLeft-hand dipped beam headlight
ChargerYSide light, left rear light
Á
KLight stalkQFront left headlight
ÆAccessories socketÅAirbag
ELEC
d
Windscreen de-icingôPassenger compartment ECU
Power and supply connectionîDiagnostics/Radio socket
TRight-hand dipped beam headlightHorn
ÌHornVSide light, right rear light
HScreen washer/wiperPFront right headlight
Braking system
Allocation of fuses (the presence of fuses DEPENDS ON THE EQUIPMENT LEV\
EL OF THE VEHICLE)

5.12
ACCESSORIES
Electrical and electronic accessoriesBefore installing this type of accessory (particularly for transmitters\
/receivers: frequency bandwidth, power level, po-
sition of the aerial, etc.), make sure it is compatible with your vehic\
le. You can get advice from an authorised dealer.
Only connect accessories with a maximum power of 65 watts. Fire hazard.
No work may be carried out on the vehicle’s 12 V electrical or radio circuits, except by Authorised Dealers: an incorrectly con -
nected system may result in damage being caused to the electrical equipm\
ent and/or the components connected to it.
If the vehicle is fitted with any aftermarket electrical equipment, make\
sure that the installation is correctly protected by a fuse.
Establish the rating and position of this fuse.
Use of transmission/receiving devices (telephones, CB equipment etc.).\
Telephones and CB equipment with integrated aerials may cause interferenc\
e to the electronic systems originally fitted to the
vehicle: it is advisable only to use equipment with an external aerial. \
Furthermore, we remind you of the need to conform
to the legislation in force concerning the use of such equipment.
Fitting after-market accessoriesIf you wish to install accessories on the vehicle: please contact an aut\
horised dealer. Also, to ensure the correct operation o f
your vehicle, and to avoid any risk to your safety, we recommend that you use only accessories specifically designed for y\
our
vehicle, which are the only accessories for which the manufacturer will \
provide a warranty.
If you are using an anti-theft device, only attach it to the brake pedal\
.
Obstructions to the driver
Only use mats suitable for the vehicle, attached with the pre-fitted com\
ponents, and check the fitting regularly. Do not lay on e
mat on top of another. There is a risk of wedging the pedals.

5.13
WIPER BLADE
Check the condition of the wiper
blades. How long they last depends
on you:
– clean the blades and the wind-screen regularly with soapy
water;
– do not use them when the wind- screen is dry;
– free them from the windscreen when they have not been used
for a long time.
– In freezing weather, make
sure that the wiper blades
are not stuck by ice (to
avoid the risk of the wiper
motor overheating).
– Keep an eye on the condition of
the blade.
Replace the wiper blades as soon
as they begin to lose efficiency:
approximately once a year.
When changing the blade, when it
has been removed, do not let the
wiper arm fall against the window:
risk of breaking the window.Replacement
With the ignition on and the engine
stopped:
– lift windscreen wiper arm 2 as far as
it will go;
– pivot blade 1 until it is removed from
its hinge.
Refitting
To refit the wiper blade, clip the blade
onto its hinge. Make sure that the blade
is correctly locked in position.
1
2

5.14
Choice of breakdown service
In the event of an energy fault
In the event of a fully discharged trac-
tion battery, any type of towing is per-
mitted: towing on a flatbed truck or
towing on the road using the tow eye
(please see following pages).
All other cases
Only towing on a flatbed truck is per-
mitted.
TOWING, BREAKDOWN (1/3)
Towing on a flatbed truck
Breakdown recovery must be perfor-
med on a flat surface under all circums-
tances except where the vehicle is im-
mobilised following a full discharge of
the traction battery. In the event of a
total energy loss, please see the fol-
lowing pages.
Before repairs, insert the key in the igni-
tion to unlock the steering column. Turn
the key to position M.
The regulations in force for breakdown
recovery must always be observed.

5.15
TOWING, BREAKDOWN (2/3)
In the event of an energy
fault: towing
In the event of a fully discharged trac-
tion battery:
– warning light
\b flashes on the ins-
trument panel;
– battery warning light 1 on the instru-
ment panel is empty.
It is possible to recover on a flatbed
truck or tow the vehicle using the tow
eye, following the instructions below.
1
Before towing, insert the key in the
switch to unlock the steering column.
Turn key to position M.
The column is unlocked, the accessory
functions are supplied: the vehicle lights
can be used (hazard warning lights,
brake lights etc.). The towed vehicle’s
lights must be switched on at night.
The speed specified by current legisla-
tion for towing must always be obser-
ved.

5.16
TOWING, BREAKDOWN (3/3)
Access to the towing point
Remove screws 2 under the front
bonnet and clips 1. Lift up the bonnet.
Only use the front and rear towing
points 3.
This towing point may only be used for
towing: never use it for lifting the vehi-
cle directly or indirectly.
Do not remove the key from
the ignition when the vehi-
cle is being towed.
3
Take care not to allow anything to
hit the 12 volt battery during towing.
1
2